ADLINK Technology NuPRO-A331 Operation & User’s Manual

When enabled, Intel® Virtualization Technology (Intel® VT) makes a single system appear as multiple independent sys- tems to software. This allows for multiple, independent operat- ing systems to be running simultaneously on a single system. Intel® C-STATE Tech C-states are proc ...

ADLINK Technology NuPRO-A331 Remote access configuration provides the settings to allow remote access by another computer to get POST messages and send commands through serial port access. Remote Access Select this option to enable or disable the BIOS remote access feature. Enabling Remote Access requires a dedicated serial por ...

ADLINK Technology NuPRO-A331 IRQ# Typical Interrupt Resource Connected to Pin Available 0 Counter 0 N/A No 1 Keyboard controller N/A No 2 Cascade interrupt from slave PIC N/A No 3 Serial Port 5 (COM5) IRQ3 via SERIRQ, IRQ3 at ISA bus Note (1) 4 Serial Port 1-4 (COM1.2.3.4) IRQ4 via SERIRQ, IRQ4 at ISA bus Note (1) 5 Serial Port 6 (COM6) IRQ5 via ...

Bus # Device # Function # Routing Description 00h 00h 00h N/A Intel PCH 5 Series Bridge 00h 01h 00h Internal PEG #1 Root Port 01h 00h 0FFh N/A PEG #1 Portt 00h 02h 00h Internal PEG #2 Root Port 02 00h 0FFh N/A PEG #2 Portt 00h 03h 00h Internal PEG #3 Root Port 03 00h 0FFh N/A PEG #3 Portt 00h 03h 00h Internal ...

ADLINK Technology NuPRO-A331 plate is under the screw as indicated. 8. Lower the locking arm and fasten it to the retention tab (A). The load plate should be locked underneath the screw as shown (B). A B . ...

ADLINK Technology NuPRO-A331 routine to skip some of its tests during bootup for faster system boot. Quiet Boot When this feature is enabled, the BIOS will display the full- screen logo during the boot-up sequence, hiding normal POST messages. When it is disabled, the BIOS will display the normal POST ...

ADLINK Technology NuPRO-A331 { outportb(IT8783_ioPort, 0x20); ID1 = inportb(IT8783_ioPort+1); outportb(IT8783_ioPort, 0x21); ID2 = inportb(IT8783_ioPort+1); } void IT8783_WDTRun(unsigned int count_value, unsigned int PLEDflag) //for NuPRO-A331 { unsigned long tempCount; unsigned int registerValue; outportb(I ...

GP37 outportb(IT8783_ioPort, 0xf9); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x02; registerValue &= 0xfb; outportb(IT8783_ioPort+1, registerValue); } outportb(IT8783_ioPort, 0x71); registerValue = inportb(IT8783_ioPort + 1); reg ...

ADLINK Technology NuPRO-A331 The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system. First press to enter the sub-menu. Then you may use the arrow keys to select the desired device, then press <+>, <-> or , key to move it up/down in the priority list. 5. ...

ADLINK Technology NuPRO-A331 that the notch matches the break on the socket. Break Notch  4. Insert the module firmly into the slot until the retaining clips snap back inwards and the module is securely seated. ...

ADLINK Technology NuPRO-A331 ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ��������� 166 � 9 � Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: [email protected] Ampro ADLINK Technology, Inc. Addres ...

ADLINK Technology NuPRO-A331 Setup screen. You can display an Exit BIOS Setup option by high- lighting it using the < Arrow > keys. The Exit BIOS Setup screen is shown below. Save Changes and Exit When you have completed the system configuration changes, select this option to leave S ...