ADLINK Technology com express Operation & User’s Manual

ADLINK Technology com express Pin Signal Pin Signal 1 LVDS_CLK_A 2 LVDS_DTA_A 3 PNL_PWR 4 PNL_PWR 5 GND 6 LVDS_A-N0 7 LVDS_A-P0 8 VDD_EN 9 LVDS_A-N1 10 LVDS_A-P1 11 BL_EN_2 12 LVDS_A-P2 13 LVDS_A-N2 14 N.C 15 LVDS_ACLK _ N 16 LVDS_ACLK _ P 17 PNL_PWR 18 LVDS_A-P3 19 LVDS_A-N3 20 GND 21 LVDS_B-N0 22 LVDS_B-P0 23 GND 24 LVDS_B-N1 ...

ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan 新北市中和區建一路 166 號 9 樓 Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: [email protected] Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, ...

ADLINK Technology com express Make the appropriate cable to connect the TTL Output Connector (CN5) and Backlight Control Connector (CN8) on the FPTB to the target TTL display panel. 3.4 FPTB Power Connector Connect the Floppy Drive power connector of your power supply to the FPTB Power Connector (CN1). 3.5 Power Up the System Assemble the rest of your syst ...

ADLINK Technology com express Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: [email protected] ADLINK Technology Japan Corporation Address: 〒101-0045 東京都千代田区 神田鍛冶町 3-7-4 神田 374 ビ ビ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku ...

ADLINK Technology com express Disclaimer The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential ...

and TTL flat panel displays with COM Express systems. The FPTB is equipped with an LVDS-to-TTL converter to allow users to implement TTL displays with COM Express systems that support LVDS only. Onboard PWM circuitry supports backlight contro ...

ADLINK Technology com express • nanoX/Express-BASE → FPTB → Customer’s cable to TTL display: This configuration provides LVDS-to-TTL conversion and backlight control when using an ADLINK reference carrier board with a TTL display. User must provide the cable connection from the FPTB's TTL output and backli ...

ADLINK Technology com express Pin Signal Pin Signal 1 GND 2 FCLK 3 GND 4 FR0 5 FR1 6 FR2 7 GND 8 FR3 9 FR4 10 FR5 11 GND 12 FR6 13 FR7 14 FG0 15 GND 16 FG1 17 FG2 18 FG3 19 GND 20 FG4 21 FG5 22 GND 23 FG6 24 FG7 25 FB0 26 GND 27 FB1 28 FB2 29 FB3 30 GND 31 FB4 32 FB5 33 FB6 34 GND 35 FB7 36 HS (HSYNC) 37 VS (VSYNC) 38 GND 39 DE ( ...

ADLINK Technology com express CN1: Power Connector (Floppy power connector) Pin Signal 1 +5V 2 GND 3 GND 4 +12V CN4: LVDS Input Connector (2x17 box header, 2.00 mm pitch) Pin Signal Pin Signal 1 LVDS_CLK_A 2 LVDS_DTA_A 3 PNL_PWR 4 PNL_PWR 5 GND 6 LVDS_A-N0 7 LVDS_A-P0 8 VDD_EN 9 LVDS_A-N1 10 LVDS_A-P1 11 BL_EN_2 12 LVDS_A-P2 13 LVDS_A-N2 14 N.C 15 LVDS_ACLK ...

ADLINK Technology com express JP1: Backlight Voltage Jumper Configuration 1 - 2 +12V 3 – 4 Reserved 5 – 6 +5V* JP2: Panel Voltage Jumper Configuration 1 - 2 +12V 3 – 4 Reserved 5 – 6 +5V 7 - 8 Reserved 9 - 10 +3.3V* JP4: LVDS/TTL Mode Jumper Configuration 1 - 2 TTL Output Active 3 - 4 Reserved 5 - 6 LVDS Output Active* JP5: Backlight Control Mode Jumper Config ...

ADLINK Technology com express Customer’s cable to TTL panel: This configuration provides LVDS-to-TTL conversion and backlight control when using a customer carrier board with a TTL display. User must provide the cable connections from the customer carrier board LVDS output to the FPTB's LVDS input conne ...