Oce TDS100 Quick Reference Manual

Replace media rolls How to replace a media roll Step Action 1 Open the drawer with roll 1 or the door in front of roll 2. 2 Replace the media roll and follow the instructions on the sticker. 3 Use the 'Feed' key to select the roll number of the new roll. 3 Use the 'Media' key to select the media type of the new roll. 4 Use the adjust ...

Oce TDS100 The components 6 The operator panel 8 Make copies 11 Replace media rolls 12 Add toner 13 Clear jams 15 ...

Oce TDS100 5 Lift the green handle and close the fuser cover. 6 Close the left cover. Tighten the nut at the left back side. 7 Turn on the Océ TDS100. Step Action ...

15 Clear jams How to remove a jammed original Step Action 1 Open the top cover in case of a fragile original. Pull the top cover towards you and lift the top cover to open it. 2 Pull the original carefully with two hands towards you 3 Check on a media jam also and clear the media jam if necessary ...

Oce TDS100 The operator panel 4 2 0 -2 -4 media paper roll 1 trailing synchro film roll 2 leading standard feed manual strip cut toner media jam 6 8 1 2 3 4 5 14 13 10 12 7 9 11 ...

17 How to remove the media from the fuser unit Caution: The fuser section can be hot. Attention: The jammed media can contain loose toner. Step Action 1 Turn off the Océ TDS100. 2 Loosen the nut at the left back side. Open the left cover. 3 Lift the green handle and open the fuser cover. 4 Remove the jammed media carefully. Note: Make ...

Oce TDS100 The keys Note: Some functions may not be available on your Océ TDS100 due to the differences in the configurations. Nr. Key Function 6 'Media' Select the media type. 7 'Feed' Select the media feed method. 8 Exposure Adjust the exposure. Use the exposure setting to correct the background of the copy. 9 'Strip' Select the edge for the ...

Oce TDS100 3 Turn the bottle in the vertical position. 4 Wait until the bottle is empty. Return the bottle into the original position. 5 Turn the bottle anticlockwise to loosen the bottle from the bottle holder. 6 Pull the waste toner bag from its holder. Close the waste toner bag. 7 Slide the new waste toner bag over the holder. 8 Close the le ...

Oce TDS100 9 The indicators Nr. Indicator Function 1 'Toner' Indicate that the Océ TDS100 has run out of toner. 2 Green light Indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 Red light Indicate that an error has occurred. 4 'Media jam' ■ Indicate that the original or copy media has jammed. � ...

Oce TDS100 13 Add toner How to add toner Step Action 1 Loosen the nut at the left back side. Open the left cover. 2 Before you open the bottle, shake the toner bottle thoroughly. Put the toner bottle in the bottle holder. Turn the bottle clockwise to fasten the bottle. ...

Oce TDS100 7 Note: Some components may not be available on your Océ TDS100 due to the differences between the configurations. 7 Integrated receiving tray Receive the copies. 8 Top cover Give access to the transparent plate. 9 Fuser cover Give access to the fuser. Note: The fuser is not visible in the illustration. 10 Left cover Give access to the ...

Oce TDS100 How to remove the media from the manual feed table Attention: Make sure you lower the sheet feeder before you remove the media. Step Action 1 Open the middle cover. 2 Press the two handles at the underside of the manual feed table to lower the manual feed table. 3 Remove the jammed media carefully 4 Lift the manual feed table until ...