Cisco ASA 5508-X Manuals

Cisco ASA with FirePOWER Services Easy Setup Guide 1 Connecting PC to ASA 2 Installing ASDM 3 Configuring ASA You can easily set up your ASA in this step-by-step guide.

Cisco ASA 5508-X and ASA 5516-X Hardware Installation Guide First Published: 2015-04-07 Last Modified: 2017-06-16 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: Online Only

Cisco Systems, Inc. www.cisco.com 1 Cisco ASA 5508-X and ASA 5516-X Quick Start Guide First Published: April 7, 2015 Last Updated: April 27, 2017 1. Package Contents This section lists the package contents of the chassis. Note that contents are subject to change, and your exact contents might contain additional or fewer items. 1 ASA 5508-X or ASA 5516-X chassis 2 USB Console Cable (Type A to Type B) 3 Power cable 4 4 10-32 Phillips Screws for rack mounting 5 4 12-24 Phillips Screws for rack mounting 6 4 M6 Phillips Screws for rack mounting 7 4 M4 Phillips Screws for rack mounting 1 3 2 353664 6 7 5 4

Cisco Systems, Inc. www.cisco.com 1 Cisco Firepower Threat Defense for the ASA 5508-X and ASA 5516-X Using Firepower Management Center Quick Start Guide First Published: August 10, 2016 Last Updated: December 3, 2018 Warning: You cannot install Firepower Threat Defense 6.3 or subsequent releases on the ASA 5508-X and 5516-X. The final supported Firepower Threat Defense release for these platforms is 6.2.3. 1. Is This Guide for You? This guide explains how to complete the initial configuration of your Firepower Threat Defense device and how to register the device to a Firepower Management Center. In a typical deployment on a large network, multiple managed devices are installed on network segments, monitor traffic for analysis, and report to a managing Firepower Management Center. The Firepower Management Center provides a centralized management console with web interface that you can use to perform administrative, management, analysis, and reporting tasks. For networks that include only a single device or just a few, where you do not need to use a high-powered multiple-device manager like the Firepower Management Center, you can use the integrated Firepower Device Manager. Use the Firepower Device Manager web-based device setup wizard to configure the basic features of the software that are most commonly used for small network deployments as described in http://www.cisco.com/go/fdm-quick. 2. Package Contents This section lists the package contents of the chassis. Note that contents are subject to change, and your exact contents might contain additional or fewer items.

Cisco ASA and Firepower Threat Defense Reimage Guide Cisco ASA and Firepower Threat Defense Reimage Guide This guide describes how to reimage between ASA and Firepower Threat Defense (FTD), and also how to perform a reimage for FTD using a new image version; this method is distinct from an upgrade, and sets the FTD to a factory default state. For ASA reimaging, see the ASA general operations configuration guide, where you can use multiple methods to reimage the ASA. Supported Models The following models support either ASA software or Firepower Threat Defense Software. For ASA and Firepower Threat Defense version support, see the ASA compatibility guide or Firepower compatibility guide. • ASA 5506-X • ASA 5506W-X • ASA 5506H-X • ASA 5508-X • ASA 5512-X • ASA 5515-X • ASA 5516-X • ASA 5525-X • ASA 5545-X • ASA 5555-X • ISA 3000 • Firepower 2100 The Firepower 4100 and 9300 also support either the ASA or Firepower Threat Defense, but they are installed as logical devices; see the FXOS configuration guides for more information. Note Cisco ASA and Firepower Threat Defense Reimage Guide 1

Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices. Cisco ASA Series Firewall CLI Configuration Guide Software Version 9.4 For the ASA 5506-X, ASA 5506H-X, ASA 5506W-X, ASA 5508-X, ASA 5512-X, ASA 5515-X, ASA 5516-X, ASA 5525-X, ASA 5545-X, ASA 5555-X, ASA 5585-X, ASA Services Module, and the Adaptive Security Virtual Appliance First Published: March 23, 2015 Last Updated: April 7, 2015 Text Part Number: N/A, Online only

Mount and Connect Do not remove the rubber feet included with the ASA because they are needed for proper cooling for all mounting orientations. Note This chapter describes how to rack-mount the ASA, and how to connect the cords and cables. It contains the following sections: • Desktop Mount the ASA, on page 1 • Wall Mount the ASA, on page 2 • Rack Mount the ASA, on page 3 • Install the ASA 5506H-X in a DIN Rail, on page 4 • Connect Cables, Turn on Power, and Verify Connectivity, on page 6 • Connect to a Console Terminal or PC, on page 8 Desktop Mount the ASA You can mount the ASA on a desktop by placing it on a desk in a horizontal position. Make sure there are no blockages or obstructions within one inch of the top of the ASA or within .5 inch of the sides and back, so that nothing interferes with cooling. Do not remove the rubber feet included with the ASA. They are also needed for proper cooling. Do not stack the ASA chassis on top of another ASA chassis. If you stack the units, they will overheat, which causes the units to power cycle. Caution Mount and Connect 1

Mount and Connect This chapter describes how to rack-mount the ASA, and how to connect the cords and cables. It contains the following sections • Rack-mount the ASA , on page 1 • Connect Cables, Turn on Power, and Verify Connectivity, on page 2 • Connect to a Console Terminal or PC, on page 4 Rack-mount the ASA The ASA ships with rack-mount brackets or “ears,” which you can install on the front or the rear of the chassis. Follow these steps to install your ASA in a rack. Step 1 Attach both brackets to the sides of the ASA chassis, either to the front or rear. After the brackets are secured to the chassis, you can mount it in the rack. Step 2 Attach the chassis to the rack. We recommend that you install the chassis with the rear panel facing the cold aisle. (See the following illustration for an example of air flow from back to front.) Mount and Connect 1