IgniteNet Spark AC Wave2 Manuals

– 1 – Quick Start Guide 1. Unpack the AP ◆Spark SP-W2-AC1200 ◆Wall/Ceiling mounting bracket and securing screw ◆Wall-mount kit — 4 screws, 4 wall plugs ◆Universal AC/DC power adapter 2. Mount the AP a. Mounting the AP on a Wall At the installation location on the wall, use the wall/ceiling- mount bracket to mark four holes for the wall plugs and screws (included in wall-mount kit). Drill four holes for the wall plugs, and then insert the plugs and tap them flush with the wall surface. Use the four screws to secure the bracket to the wall. With its ports facing down, slide the AP down onto the bracket until it snaps into its secured position. Do not let go of the AP until you confirm that it is secure. b. Mounting the AP on a Ceiling Slide the wall/ceiling-mount bracket onto the rails on the back of the AP until it snaps into its secured position. Use the included screw to secure the bracket to the AP. Press the retention clips of the wall/ceiling-mount bracket against the ceiling T-bar. Rotate the AP until the T-bar snaps into place. Note: The wall/ceiling-mount bracket supports two different sizes of suspended ceiling T-bars. The position illustrated above is for 15 mm bars. Use the position at a 90 degrees angle for 24.5 mm bars. 1 1 2 1 2 3 3 4 4 2 1 1 2 3 4 c. Mounting the AP on a Pole (requires optional pole-mount kit) Attach the pole-mount bracket to the back of the AP. Use the included screw to secure the bracket to the AP. Feed the two steel-band clamps through the pole-mount bracket mounting points. Fasten the steel-band clamps around the pole to secure the AP to the pole. 3. Connect Cables a. Using the AC/DC Power Adapter Connect the cable from the AC/DC power adapter to the DC power jack on the AP. Connect the power adapter to a nearby AC power source (100-240 VAC, 50/60 Hz). Connect Category 5e or better cable to the Eth0 RJ-45 port. Connect the other end of this cable to a LAN switch. (Optional) Connect local LAN devices to the other RJ-45 port on the AP using Category 5e or better cable. This 1000BASE-T port is labeled Eth1. 1 3 2 4 4 1 2 3 4 2 3 1 1 2 3 Spark SP-W2-AC1200 E092017-CS 150200001744X R01 Cloud-Enabled Indoor/Outdoor Access Point Spark™ AC Wave2, SP-W2-AC1200 ignitenet.com

– 1 – Quick Start Guide 1. Unpack the AP ◆ SunSpot™ Wave2 AC2600 ◆ Wall/Ceiling mounting bracket and securing screw ◆ Wall-mount kit — 4 screws, 4 wall plugs ◆ Universal AC/DC power adapter 2. Mount the AP a. Mounting the AP on a Wall At the installation location on the wall, use the wall/ceiling- mount bracket to mark four holes for the wall plugs and screws (included in wall-mount kit). Drill four holes for the wall plugs, and then insert the plugs and tap them flush with the wall surface. Use the four screws to secure the bracket to the wall. With its ports facing down, place the AP over the bracket flanges and then slide it down until it snaps into its secured position. Do not let go of the AP until you confirm that it is secure. b. Mounting the AP on a Ceiling Place the wall/ceiling-mount bracket over the mounting flanges on the back of the AP, and then slide it up until it snaps into its secured position. Use the included screw to secure the bracket to the AP. Press the retention clips of the wall/ceiling-mount bracket against the ceiling T-bar. Rotate the AP until the T-bar snaps into place. Note: The wall/ceiling-mount bracket supports two different sizes of suspended ceiling T-bars. The position illustrated above is for 15 mm bars. Use the position at a 90 degrees angle for 24.5 mm bars. 1 1 2 1 2 3 3 4 4 2 1 1 2 3 4 c. Mounting the AP on a Pole (requires optional pole-mount kit) Attach the pole-mount bracket to the back of the AP. Use the included screw to secure the bracket to the AP. Feed the two steel-band clamps through the pole-mount bracket mounting points. Fasten the steel-band clamps around the pole to secure the AP to the pole. 3. Ground the AP Ensure the structure on which the unit is to be mounted is properly grounded and in compliance with local and national electrical codes. Verify that there is a good electrical connection to a grounding point (no paint or isolating surface treatment). Use the included (M4) screw to attach a grounding wire (not included) to the grounding point on the unit, and then to ground. Caution: The earth connection must not be removed unless all supply connections have been disconnected. 1 3 2 4 4 1 2 3 4 2 1 1 2 E032018-CS-R02 Cloud-Enabled Indoor/Outdoor Access Point SunSpot™ Wave2 AC2600 ignitenet.com