PDQ 5300 Manuals

5300/5500 DOOR CLOSER MODELS TOP JAMB INSTALLATION - PUSH SIDE - PIVOT STOP (PS) ARM APPLICATIONS INSTRUCTION: 539356 REV.0 10-01-19 MACHINE SCREWS: USE #7 OR 13/64" [5.1] DRILL AND 1/4-20 TAP WOOD DOOR/FRAME SCREWS: USE 5/32" [4] DRILL SEX NUTS: USE 3/8" [9.5] DRILL (CLOSER TO DOOR) PDQ Manufacturing 2230 Embassy Dr. Lancaster, PA 17603 833-273-7832 833-2 PDQTECH www.pdqlocks.com CL HINGE OR PIVOT 1 3/4" [44.5] 1 7/8" [47.6] 12" [304.8] 3/4" [19.1] 1/2" [12.7] A BOTTOM OF FRAME FACE Opening Dim. A Dim. B 85° 10-3/8" [263.5] 15-7/8" [403.2] 90° 9-3/4" [247.7] 15-1/4" [387.4] 95° 9-3/16" [233.4] 14-11/16" [373.1] 100° 8-11/16" [220.7] 14-3/16" [360.4] 105° 8-5/16" [211.1] 13-13/16" [350.8] 110° 7-15/16" [201.6] 13-7/16" [341.3] NOTES: 1. DO NOT SCALE DRAWING. LEFT HAND DOOR SHOWN. 2. DIMENSIONS ARE GIVEN IN INCHES [MM]. 3. FOR DOORS WITH REVEAL OF 4 INCHES. CONSULT FACTORY FOR OTHER REVEAL DEPTHS. 4. MINIMUM CEILING CLEARANCE FROM BOTTOM OF FRAME FACE FOR CLOSER : 2-11/16". 5. SEX NUTS REQUIRED FOR UNREINFORCED OR COMPOSITE FIRE DOORS. 6. DOOR AND FRAME MUST BE REINFORCED PER ANSI/SDI A250.8 REQUIREMENTS - MINIMUM THICKNESS RECOMMENDED FOR REINFORCEMENTS IN HOLLOW-METAL DOORS AND FRAMES: 0.067" UNLESS OTHERWISE NOTED. 7. HOLLOW-METAL DOORS REQUIRE CHANNEL OR BOX-TYPE REINFORCEMENT WHEN SEX NUT MOUNT IS SPECIFIED. B

REGULAR ARM INSTALLATION - PULL SIDE - NON-HOLD OPEN AND HOLD OPEN APPLICATIONS 5300/5500 DOOR CLOSER INSTRUCTION SHEET CLOSER BODY (RIGHT HAND DOOR) CLOSER BODY (LEFT HAND DOOR) SWEEP/ LATCH VALVES THIS END OF BODY FOOT (RH DOOR) FOLD AT HINGE/PIVOT CENTERLINE FOR THE REQUIRED OPENING ANGLE. FOLD BACK FOLD BACK FOLD BACK TO 100° MAX TO 130° MAX TO 180° MAX FOLD HERE (LH) FOLD HERE (RH) MACHINE SCREWS: USE #7 OR 13/64" [5.1] DRILL AND 1/4-20 TAP WOOD DOOR/FRAME SCREWS: USE 5/32" [4.0] DRILL SEX NUTS: USE 3/8" [9.5] DRILL THIS SIDE UP FOR RH DOOR THIS SIDE UP FOR LH DOOR FOOT (LH DOOR) INSTRUCTION: 539351 REV. 3 09-05-19 ALIGN WITH BOTTOM OF FRAME (RH) ALIGN WITH BOTTOM OF FRAME (LH) /PIVOT CENTERLINE ALIGN WITH HINGE BOTTOM OF FRAME HINGE CL A B 1 3/4" [44.5] 1 1/4" [31.8] 1 1/8" [28.6] OPENING TO 100° TO 130° TO 180° DIM A 7-1/2"[190.5] DIM B 13"[330.2] 11-1/2"[292.1] 6"[152.4] 10"[254] 4-1/2"[114.3] 3/4" [19.1] RH ALIGN WITH HINGE /PIVOT CENTERLINE PULL SIDE FACE OF DOOR 12" [304.8] PDQ Manufacturing 2230 Embassy Dr. Lancaster, PA 17603 833-273-7832 833-2 PDQTECH www.pdqlocks.com

5300/5500 DOOR CLOSER INSTRUCTION SHEET INSTRUCTION: 539354 REV. 4 09-05-19 SWEEP/ LATCH VALVES THIS END OF BODY CLOSER BODY (LEFT HAND DOOR) CLOSER BODY (RIGHT HAND DOOR) TO 90° MAX TO 95° MAX TO 100° MAX TO 105° MAX THIS SIDE UP FOR RH DOOR FOLD BACK TO 85° MAX FOLD AT HINGE/PIVOT CENTER -LINE THAT MATCHES REQUIRED STOP/HOLD OPEN ANGLE . STOP MACHINE ONE ADDITIONAL HOLE AFTER INSTALLATION OF BRACKET BRACKET (LH DOOR) MACHINE ONE ADDITIONAL HOLE AFTER INSTALLATION OF BRACKET BRACKET (RH DOOR) MACHINE SCREWS: USE #7 OR 13/64" [5.1] DRILL AND 1/4-20 TAP WOOD DOOR/FRAME SCREWS: USE 5/32" [4.0] DRILL SEX NUTS: USE 3/8" [9.5] DRILL THIS SIDE UP FOR LH DOOR UNDERSIDE OF SOFFIT / STOP FOLD HERE (RH) FOLD HERE (LH) UNDERSIDE OF SOFFIT / STOP FOLD BACK FOLD BACK FOLD BACK FOLD BACK FOLD HERE, POSITION ON DOOR AND ALIGN WITH BOTTOM OF STOP (LH) PARALLEL ARM INSTALLATION - PUSH SIDE - DS (NHO) AND DSHO (HO) APPLICATIONS - 105° MAX /PIVOT CENTERLINE ALIGN WITH HINGE /PIVOT CENTERLINE ALIGN WITH HINGE /PIVOT CENTERLINE ALIGN WITH HINGE /PIVOT CENTERLINE ALIGN WITH HINGE /PIVOT CENTERLINE ALIGN WITH HINGE STOP MAY OCCUR APPROX. 3°- 5° BEYOND POSITION NOTED (DUE TO COMPRESSION OF BUMPER) BOTTOM OF STOP HINGE CL B A 2 1/8" [54.0] 5/8" [15.9] 12" [304.8] 2 15/16" [74.6] 3/4" [19.1] OPENING TO 85° TO 90° TO 100° DIM A 3-7/8"[98.4] DIM B TO 105° 8-7/8"[225.4] 8-1/4"[209.6] 3-1/4"[82.6] 7-1/16"[179.4] 2-1/16"[52.4] 6-1/2"[165.1] 1-1/2"[38.1] TO 95° 7-11/16"[195.3] 2-11/16"[68.3] STOP FOLD HERE, POSITION ON DOOR AND ALIGN WITH BOTTOM OF STOP (RH) FOLD HERE (LH) FOLD HERE (RH) PDQ Manufacturing 2230 Embassy Dr. Lancaster, PA 17603 833-273-7832 833-2 PDQTECH www.pdqlocks.com

CL HINGE OR PIVOT 1 3/4" [44.5] 3/4" [19.1] 12" [304.8] A B 1 1/8" [28.6] BOTTOM OF FRAME FACE 5300/5500 DOOR CLOSER MODELS REGULAR ARM INSTALLATION - PULL SIDE - PIVOT STOP (PS) ARM APPLICATIONS INSTRUCTION: 539355 REV.0 10-01-19 NOTES: 1. DO NOT SCALE DRAWING. LEFT HAND DOOR SHOWN. 2. DIMENSIONS ARE GIVEN IN INCHES [MM]. 3. MINIMUM CEILING CLEARANCE FROM BOTTOM OF FRAME FACE FOR CLOSER ARM : 1-5/8". 4. SEX NUTS REQUIRED FOR UNREINFORCED OR COMPOSITE FIRE DOORS. 5. DOOR AND FRAME MUST BE REINFORCED PER ANSI/SDI A250.8 REQUIREMENTS - MINIMUM THICKNESS RECOMMENDED FOR REINFORCEMENTS IN HOLLOW-METAL DOORS AND FRAMES: 0.067" UNLESS OTHERWISE NOTED. 6. HOLLOW-METAL DOORS REQUIRE CHANNEL OR BOX-TYPE REINFORCEMENT WHEN SEX NUT MOUNTING IS SPECIFIED. MACHINE SCREWS: USE #7 OR 13/64" [5.1] DRILL AND 1/4-20 TAP WOOD DOOR/FRAME SCREWS: USE 5/32" [4] DRILL SEX NUTS: USE 3/8" [9.5] DRILL (CLOSER TO DOOR) Opening Dim. A Dim. B 85° 10-13/16" [274.6] 16-5/16" [414.3] 90° 10-1/8" [257.2] 15-5/8" [396.9] 95° 9-1/2" [241.3] 15" [381] 100° 8-15/16" [227] 14-7/16" [366.7] 105° 8-1/2" [215.9] 14" [355.6] 110° 8-1/8" [206.4] 13-5/8" [346.1] PDQ Manufacturing 2230 Embassy Dr. Lancaster, PA 17603 833-273-7832 833-2 PDQTECH www.pdqlocks.com