RHINO 2409 Manuals

© 2011 Alamo Group Inc. $0.00 2409 Published 01/11 Part No. F-3644C OPERATOR’S MANUAL RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: [email protected] LOADER This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01- Cover

F-3978 1 of 4 7-2-2004 2-7414 MOUNT KIT 2409 LOADER MASSEY FERGUSON TRACTORS ASSEMBLY MANUAL Keep With Operator's Manual Mounting brackets can be installed using tools ordinarily available. Shut off tractor engine and engage tractor brakes during installation. After loader is installed, check to be sure front tires clear loader and mounting brackets in all possible positions. NOTE: Leave all attaching hardware loose until mount- ing brackets are completely assembled to facilitate as- sembly and proper alignment. Tighten all hardware to torque specifications in loader operators manual. INSTALLING MOUNTING BRACKETS (Figure 1) 1. Remove bolts securing tractor front weight bracket to tractor front casting. Refasten weight bracket with front mounting bracket (1) mounted over front weight bracket using 5/8 x 2” cap screws (15) and 5/8” lock washers (18). 2. Install left midmounting bracket (4) to tractor trans- mission casting using 3/4” spacer (5), 5/8” flat washer (19), 5/8” lock washer (18) and 5/8 x 2-1/2” cap screw (8) in upper rear hole and 5/8” flat washer (19), 5/8” lock washer (18) and 5/8 x 1-1/2” cap screw (9) in upper front hole. Fasten lower holes in left midmounting bracket using .69” spacers (6), 5/8 lock washers (18) and 5/8 x 2-1/4” cap screws (16). 3. Install right midmounting bracket (3) to tractor cast- ing using 3/4” spacer (5), 5/8” flat washer (19), 5/8” lock washer (18) and 5/8 x 2-3/4” cap screw (14) in upper rear hole and 5/8” flat washer (19), 5/8” lock washer (18) and 5/8 x 1-3/4” cap screw (17) in upper front hole. Fasten lower holes in right midmounting bracket using 2.69” spacers (7), 5/8” lock washers (18) and 5/8 x 4-1/4” cap screws (21). 4. Remove inspection cover plate on underside of clutch housing. 5. Fasten cross tie (2) to right and left mid mounting brackets (3 & 4) using 5/8 x 2” cap screws (15) and 5/8” lock nuts (20). 6. Fasten cross tie to bottom of tractor using 5/8” flat washers (19), 5/8” lock washers (18) and 5/8 x 1-3/4” cap screws (17). MODEL 2WD 4WD LESS CAB WITH CAB MF431 X X

F-3676 Page 1 of 4 1-7-2005 ASSEMBLY MANUAL 2-7126 Keep with Operator’s Manual LOADER MOUNTING KIT 2409 LOADER NEW HOLLAND TRACTORS MODEL 2WD FWA ROPS SOFT CAB 2120 After S/N UV32236 X X X X 3415 X X X X TRACTOR AND MOUNTING KIT GENERAL INFORMATION Mounting kit can be installed on tractor using tools ordinarily available. IMPORTANT: This mounting kit is compatible with vertical exhaust only. Mounting kit is not compatible with front weights. If tractor is equipped with front weights, they must be removed before mounting loader. It is not necessary to remove front weight bracket. NOTE: If installing optional grille guard (2-6225), install grille guard and front mounting bracket (1, Figure 1) at same time. Check tire clearances when loader installation is complete and adjust tread width as necessary to provide adequate clearance. Shut off tractor engine and engage parking brakes during installation. INSTALLING LOADER MOUNTING BRACKETS (Figure 1) NOTE: Install all attaching hardware loosely (unless noted otherwise) until mounting kit is completely assembled to facilitate assembly and proper alignment. Tighten all hardware to torques specified in general torque specifications table. 1. Attach front mounting bracket (1) to sides of tractor front frame using 1/2 x 2" cap screws (10) and lock nuts (14). 2. Support tractor auxiliary valve and bracket and remove four 16mm cap screws which secure valve bracket (A) to mounting pad on right side of tractor clutch housing. Support right side of tractor engine and front frame and remove five 14mm cap screws from tractor frame and engine casting ahead of mounting pad. 3. With valve bracket sandwiched between, fasten right mid mounting bracket (3) to tractor clutch housing using four 16mm x 50 mm cap screws (8) and 5/8" lock washers (11), and with tractor front frame to engine block using five 14mm x 55mm cap screws (9) and 9/16" lock washers (12). 4. Support left side of tractor engine and front frame and remove five 14mm cap screws from tractor frame ahead of mounting pad. 5. Fasten left mid mounting bracket (2) and spacer plate (6) to tractor clutch housing using four 16mm x 50 cap screws (8) and 5/8" lock washers (11) and with tractor front frame to engine block using five 14mm x 55mm cap screws (9) and 9/16" lock washers (12). NOTE: Tighten 16mm cap screws (8) to 130-158 ft.·lbs. of torque. Tighten 14mm cap screws (9) to 85-103 ft.·lbs. of torque. MOUNTING LOADER ONTO TRACTOR AND MOUNTING BRACKETS WARNING: To avoid injury during installation of quick attach loader, do not permit bystanders within ten feet of loader or tractor. 1. Loop chain under each lift cylinder and hook on loader boom arm. Using overhead hoist to support loader, remove hardware securing loader to pallet. Lift loader and remove pallet. CAUTION: Do not damage grease fitting on end of cylinder. Be sure chain does not pinch lift cylinder. 2. Using overhead hoist, lower loader from vertical shipping position to horizontal position, leaving enough room to install yoke. (Scraps of cardboard may be used to protect paint.) Fasten yoke assembly (4) to loader side frames using 3/4 x 2- 1/2" cap screws (7) and lock nuts (13).

F-3926 1 of 6 3-23-04 2-7233 ASSEMBLY MANUAL Keep With Operators Manual LOADER MOUNT KIT 2409 LOADER AGCO ST45, ST55 and MASSEY FERGUSON 1165, 1445, 1455, 1455V TRACTORS Mount kit can be installed using tools ordinarily available. Shut off engine and engage brakes during installation. Check tire clearances once loader is installed and adjust tire tread width and/or turning radius if necessary. NOTE: Unless specified, leave all attaching hardware loose until loader is completely assembled to facilitate assembly and proper alignment. Torque hardware to specifications listed on page 5. TRACTOR PREPARATION 1. Shut off engine and engage brakes during installation of mount kit. 2. Remove front weight bracket. 3. Raise hood and remove hood side panels to prevent damage during loader mount installation. INSTALLING LOADER MOUNT BRACKETS (Figure 1) 1. Attach front mount bracket (3) using 14MM x 35MM cap screws (9) and 9/16 lock washers (15). 2. Remove and discard 14MM cap screws and lock washers where mid mount brackets are bolted to tractor frame. 3. Attach mid mounting brackets (1 & 2) to mounting pads below tractor platform using 16MM x 40MM cap screws (6) and 5/8 lock washers (10). Leave 16MM cap screws (6) and 5/8 lock washers (10) loose to ease installation. A) AGCO ST45, MF1165 and MF 1445 requires two 5/8 spacers (5) each side between mid mounting bracket and tractor frame. B) AGCO ST45, MF1165 and MF1445 - Install mid mounting bracket (1 & 2) to tractor frame using 14MM x 60MM cap screws (7), 9/16 flat washers (14) and 9/16 lock washers (15). C) AGCO ST55, MF1455 and MF1455V - Install mid mounting brackets (1 & 2) to tractor frame using 14MM x 40MM cap screws (8), 9/16 flat washers (14) and 9/16 lock washers (15). To access bottom hole on frame, 14MM bolt (7 or 8), 9/16 flat washer (14) and 9/16 lock washer (15) must pass through support tube of mid mounting assembly (1 & 2). 4. Reinstall hood side panels and lower hood to locked position. MODEL 2WD FWA CAB LESS CAB AGCO ST45 X X AGCO ST55 X X MF 1165 X X MF 1445 X X MF 1455 X X MF 1455V X X