Sekonic SR-3500 Operating Manual

Please read the operating manual before using this product, and be sure to use it properly. After reading this operating manual, be sure to keep it in a place that you can access at any time. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Introduction

Safety precautions .............................................................................................. 5 Before using .......................................................................................................... 8 Power cord list for Europe .................................................................................. 11 Warranty .................................................................................................................. 12 Precautions for use ............................................................................................ 13 Names of parts ..................................................................................................... 16 ■Operating panel functions and operating instructions ................................ 18 Product specifications ...................................................................................... 19 Operation ■Preparation ....................................................................................................... 21 ■Turning power on ............................................................................................. 25 ■Loading paper .................................................................................................. 26 ■Setting paper weight ....................................................................................... 28 Marking instructions .......................................................................................... 29 Connecting to a computer .............................................................................. 30 ■USB 1. Operating mode............................................................................................. 31 2. Interface settings........................................................................................... 32 ■RS-232C 1. Operating mode............................................................................................. 33 2. Interface settings 2-1. Setting baud rate................................................................................... 34 2-2. Setting character bit length................................................................... 34 2-3. Setting parity......................................................................................... 35 2-4. Setting stop bit...................................................................................... 36 2-5. Setting flow control............................................................................... 36 2-6. Setting character code.......................................................................... 37 Data reading settings ■Setting column ................................................................................................. 38 ■Setting reading method .................................................................................. 39 ■Setting min. density level ................................................................................ 41 ■Setting density balance ................................................................................... 42 ■Setting reading side ........................................................................................ 43 ■Setting paper weight ....................................................................................... 44 ■Setting paper hold(SR-3500)............................................................................ 45 Error detection settings .................................................................................... 46 Buzzer settings ■Buzzer control .................................................................................................. 48 ■Buzzer sound adjustment ............................................................................... 49 Table of contents

Printer settings ■Printer control .................................................................................................. 51 ■SR-2300 SR-6500 mode 1. Character size setting.................................................................................... 52 2. Character interval setting............................................................................... 53 ■SR-600 SR-9000 mode 1. Character size setting.................................................................................... 55 2. Character magnification setting..................................................................... 56 3. Character interval setting............................................................................... 57 Barcode settings ■Barcode control ............................................................................................... 59 Low power consumption settings ■Sleep duration................................................................................................... 60 ■Stanby duration................................................................................................. 61 Displaying various information ■Displaying the version ..................................................................................... 62 ■Displaying front side reading sensor settings .............................................. 63 ■Displaying back side reading sensor settings .............................................. 64 ■Displaying optional unit settings .................................................................... 65 ■Displaying total count...................................................................................... 66 ■Displaying serial number................................................................................. 67 Operating tests ■Feed test 1 ........................................................................................................ 68 ■Feed test 2 ........................................................................................................ 69 ■Printer test ........................................................................................................ 70 ■Printer jet test .................................................................................................. 71 Options Stacker unit ■Stacker unit specifications ............................................................................. 72 ■Stacker unit (printer) preparation ................................................................... 73 ■Printing position adjustment .......................................................................... 76 ■Clearing paper jams ........................................................................................ 79 ■Stacker unit precautions for use .................................................................... 80 Back side reading unit ...................................................................................... 81 Printer unit ■Printer unit specifications ............................................................................... 82 ■Printer uniut preparation ................................................................................. 84 ■Printable area ................................................................................................... 84 ■Printing position adjustment .......................................................................... 85 ■Printer unit precautions for use ..................................................................... 87 Barcode unit / V • Barcode unit / H ■Barcode unit specifications ............................................................................ 88 Table of contents

■Barcode reading position adjustment ........................................................... 92 ■Barcode unit precautions for use ................................................................... 94 Cleaning .................................................................................................................. 95 ■Cleaning procedures ....................................................................................... 95 ■Cleaning point .................................................................................................. 96 Service schedule ............................................................................................... 100 External diagram ............................................................................................... 102 List of menu modes .......................................................................................... 104 Error displays and countermeasures 1. Errors............................................................................................................ 107 2. Warnings...................................................................................................... 111 OMR glossary ..................................................................................................... 114 Appendix ■Sheet creation reference Table of contents

product so as to prevent users or other people from being injured, or property from being damaged. Read these precautions thoroughly and understand the meanings of the symbols before proceeding to the main text of this manual. Safety Precautions Warning Improper operation by neglecting these instructions may result in death or serious injury. Caution Improper operation by neglecting these instructions may result in personal injury or property damage. Neglecting these instructions may generate smoke or fire. Neglecting these instructions may cause electric shock. Indicates a prohibited action. Indicates that disassembly or modification is prohibited. Indicates that the power plug must be removed from the outlet for safe operation. Instructs that do not spray the materials containing an inflammble gas or liquid to the device.

when there is a strange smell or sound. In such a case, immediately turn the power switch off and then remove the power plug from the outlet. After making sure that it is no longer smoking, ask the sales shop for repair service. Never attempt to repair by yourself since that may be very dangerous. ● Do not modify or disassemble this device. That could cause fire or electric shock. ● Do not remove the cover from this device. That could cause electric shock. Ask the sales shop to conduct any internal checking, adjustment or repair. Pay thorough attention to the above instructions. Otherwise, fire or electric shock may occur. ● Power plug precautions • Do not pull on the cord when removing the power plug from the outlet. • Do not use any power plug other than the specified one. Make sure to use the adapter included in the package. ● Device precautions • Do not use it with a supply voltage other than the specified one. • Do not install it in a place that may be wet with water or oil, steam, moisture or dust. • Do not insert or drop any metal, foreign combustible matter, etc., into the port. • Do not place containers with chemicals or water, or small metal pieces near the device. ● Do not cover the vent hole. That could cause heat retention, resulting in fire. ● If the device is dropped or the cover is broken, immediately turn the power switch off and remove the power plug from the outlet. Then, contact the sales shop. ● If any foreign matter should enter inside, immediately turn the power switch off and remove the power plug from the outlet. Then, contact the sales shop or Sekonic. If the device continues to be used with foreign matter inside, fire or electric shock may occur. If water or other substances penetrate the unit, immediately turn the power switch off and remove the power plug from the outlet. Then, contact the sales shop or Sekonic. If the device continues to be used with water or other foreign matter inside, fire or electric shock may occur. ● Do not spray any materials containing an inflammable gas or liquid on the device and be sure to keep this kind of materials away from this device. Use a cleaning cloth with suitable amount of cleaning liquid to wipe off well, after removing the power plug from the outlet and the device becomes to cool off.

collapse, resulting in injury. ● Do not place the device in an unstable location. Otherwise, it may fall or collapse, resulting in injury. ● When opening or closing the upper part of the main body, do not place your hand on the paper-feeding surface. Otherwise, fingers may be caught, resulting in injury. ● If you must touch the paper-feeding surface of the main body, be careful not to allow your fingers to be caught or hit. ● When doing maintenance on the device, for your own safety, be sure to remove the power plug from the outlet. ● When the device is not in use for long periods, for safety, remove the power plug from the outlet. ● Before moving the device, be sure to remove the power plug from the outlet. If the cable is damaged, fire or electric shock may occur. ● Do not connect or disconnect the power plug if your hands are wet. Otherwise, an electric shock may occur. Caution

components are missing or damaged, contact the store where you purchased the device. Note) The package doesn’t include a RS-232C(9 pins) interface cable. You may need to get one depending on your computer port or connection method. 5. Power cord For U.S.A Mark entry sheet: use it as an example when designing entry sheets. 6. Operating manual (this booklet) 7. A4 check sheets (5 sheets) A4 mark entry sheets (5 sheets) 9. USB cable 1. Main body unit 2. Paper receiver 3. Paper discharge brackets ( x 2: Not used when the select ) stacker unit is installed. For Europe Note) Refer to the power cord list for Europe of next page. 8. CD-ROM 4. Paper feeding bracket ( Not used when the select ) stacker unit is installed. Check sheet: use it for checking OMR operations. Operating manual Before using

(Transparent plastic bag) Stacker unit (Option) * See the installation manual for components to be used for installation. 1. Stacker 2. Main tray 3. Selection tray Printer unit (Option) 1. Ink cartridge

components are missing or damaged, contact the store where you purchased the device. 5. Power cord For U.S.A 6. Operating manual (this booklet) 9. USB cable 1. Main body unit 2. Main tray 3. Selection tray 4. Paper feeding bracket For Europe Note) Refer to the power cord list for Europe of next page. 8. CD-ROM 10. Ink cartridge Mark entry sheet: use it as an example when designing entry sheets. 7. A4 check sheets (5 sheets) A4 mark entry sheets (5 sheets) Check sheet: use it for checking OMR operations. 11. Strage bag (Transparent plastic bag) Operating manual Note) The package doesn’t include a RS-232C(9 pins) interface cable. You may need to get one depending on your computer port or connection method. Before using

As stated on page 7 of this manual, the machine includes a representative variety of power adapters. If none of the included adapters match the power outlets in your location, please find and use an appropriate adapter. Before using Power cord list for Europe Country Plug type U.K. B, B3, BF, C Italy A, C, SE Austria B3, BF, C, O, SE Netherlands B, C, SE Greece B, B3, C, SE Sweden B, C, SE Spain A, C, SE Denmark C Germany A, C, SE Finland A, B, C, SE France A, C, O, SE Belgium A, B, C, SE Portugal B, B3, BF, C, SE Luxemburg A, C, SE Ireland A, B, B3, BF, C, SE A type (American Type) BF type (British Type) C type (CEE Type) B type (British Type) B3 type (British Type) SE type (CEE Type) O type (Ocean Type)

The company will repair malfunctions arising during this period free of charge if they are determined to be the company’s responsibility. In the event repairs are necessary, as a general rule the company will keep the product temporarily to carry out such repair work. Malfunctions and other failures caused by customer misuse or by wastage of the parts due to mass processing will not be covered by the warranty. This warranty covers only this product and its accessories, and the company will not assume any responsibility for monetary damage, lost earnings, or any third-party claims as a result of using this equipment. Warranty

Handle the device with the following points in mind to enable full use of its functions. • Precautions regarding installation Do not place the device in the following places. Otherwise, failures could result such as paper jams, reading errors, or the unit could become inoperative. (1) In direct sunlight or near a heating device. (2) Outdoors where the main body may not perform satisfactorily due to rain or strong wind. (3) A place where the main body may not perform satisfactorily such as it is subject to vibration while operating, or it is placed in an unstable location. (4) Places subject to sudden temperature changes, excessive moisture and dust. Recommended temperature: 10-30°C Guaranteed operating temperature range: 5-35°C Humidity: 30-80% (no condensation) Avoid environments outside the above ranges as much as possible when placing the device. • Handling precautions (1) Do not connect or disconnect the power cord or connector when the device is operating or the power switch is on. (2) Do not move the device while it is operating. Also, do not touch, pull, or push paper. (3) Do not put objects on the device, or sit or lean on it. (4) This device is designed to deferred type.Do not give it a strong vibration and shock etc. (5) Allow an interval of at least 5 seconds between turning the power switch on and off. (6) Do not insert foreign objects other than paper. (7) Do not apply force that deforms paper while it is being loaded. (8) Since the paper reading part is equipped with an optical lens, never insert a screwdriver or other such objects. (Otherwise, reading may be disabled.) If paper feeding is disabled due to dust or the like in the paper feeder, open the top cover to remove it. ( See “Cleaning” P.95) (9) If the roller becomes soiled with powder from paper or pencil lead, the roller and the paper may slip. In order to prevent slippage, clean the roller at proper intervals. ( See “Cleaning” P.95) (10) If the exterior of the device is soiled, lightly wipe with a soft cloth wetted with water or a neutral detergent. Note that wiping with a cloth wetted with volatile chemicals like benzene or paint thinner may cause deformation or discoloring. Precautions For Use

(11) Do not apply strong loads to the tray, as it may bend or break. (12) Because the aligning roller section has used the magnet, do not bring close a floppy disk and a magnetic card etc.. It becomes cause of data damage. (13) When moving the device, always hold it under the spots indicated by thegreen labels. (Never place your hands in the areas indicated in the circles.) Green label Green label Precautions For Use

(14) Make sure to observe the following points when you handle the device and USB cables. Otherwise, mechanical failure or damage may be caused. * Do not forcibly pull or bend the USB cable. * Always hold the plug when you insert or pull out the USB cable. Never apply excessive force to the cable. * When installing/moving the device or a PC, do not apply excessive power to the cord or plug of the USB cable. (15) Please do not put any substances and one’s hand on the upper cover. It will be occurred paper jamming or reading error

Names of parts Paper weight setting dial Interlock Side guide Paper feeding table (hopper) Side guide knob Display panel (LCD) Operating buttons Power switch Lock lever Aligning roller Interface Power connector

※ SR-6500 is equipped with the stacker unit standardly Paper weight setting dial Interlock Side guide knob Side guide knob Side guide Stacker unit Paper feeding table (hopper) Aligning roller Lock lever Power switch Display panel (LCD) Operating buttons Selection tray Main tray Interface Power connector Names of parts

The operating panel has five kinds of switches. The switches don’t work while the machine is performing a function. There are two modes: normal mode and menu mode. In normal mode, the machine is connected to a computer and is controlled by commands from the host. In menu mode, various settings are controlled by using panel switches. 1. UP switch (1) Normal mode: Raises the paper-feeding table. (2) Menu mode: Use it to choose menu items and to select parameters. When you push for a long time, while having pushed, it keeps increasing menu items and parameters. 2. DOWN switch (1) Normal mode: Drops the paper-feeding table. (2) Menu mode: Use it to choose menu items and to select parameters. When you push for a long time, while having pushed, it keeps increasing menu items and parameters. 3. MENU switch (1) Normal mode: Enters menu mode. (2) Menu mode: Returns to normal mode. (If there is an error, it displays the error.) 4. CLEAR/EXIT switch (1) Normal mode: If an error is displayed, you can clear the error. Clears the feed count. (2) Menu mode: If an error is displayed, you can clear the error. Moves one level higher in the hierarchy from the current level. 5. FEED/ENTER switch (1) Normal mode: Feeds one sheet. If you keep the switch depressed, paper is fed as long as the switch is depressed. (2) Menu mode: Executes the selected menu item. UP DOWN MENU CLEAR/EXIT FEED/ENTER Names of parts ■Operating panel functions and operating instructions

(* You need an optional back-surface reading unit for double-sided reading.) Darkness levels 16 levels (internal 256 levels) Light source color infra red light (940nm) [visible red light (660nm)] Pitch (inch) 1/6”, 0.2”, 0.25”, 0.3” Marking infra red light : pencil [visible red light : pencil, ballpoint pen (black or blue)] Reading marks size: 0.5×3mm or more darkness: PCS 0.6 or darker Barcode (*Optional barcode unit is necessary to use the barcode function. The selecting "V" or "H" depends on the reading direction of the bar direction. See P90-P96) Barcode styles JAN/EAN/UPC/NW7/CODE39/CODE128/ ITF/code corresponding to the model of the device (Vertical: COOP 2 of 5, industrial 2 of 5) (Horizontal: EAN-128, CODE-93) (*As for entire thickness at time of bar-code label use 0.25 mm or less) Error detection function Sheet position detection, multiple sheet feeding detection, skew detection Printing (*The printer function requires the optional stacker unit or printer unit.) PC interface USB (Ver. 2.0) 480Mbps RS-232C 9,600-115,200bps Display panel and Display panel (LCD) 20 characters x 2 lines operating switches Operating switches 5 Hopper capacity 500 sheets (paper weight 105g/m 2) Paper used Paper size IBM card size, postcard size, A5, B5, A4 8.5 inch, 9 inch Height 110-355.6mm, width 63.5-228.6mm Paper weight 84-157g/m 2 Paper quality OCR paper, bond paper, recycled OCR paper (recycled OCR paper composition 50%) Sheet feeding Feeding speed 550mm/s Approx. 3,500 sheets/hour (single-sided using a USB connection) Sheet discharge Stacker volume 500 sheets (when weight 105g/m 2 paper is used) Stacker function Yes (*Optional stacker unit is necessary to use the stacker function) Main tray: 500 sheets (when weight 105g/m 2 paper is used) Selection tray: 150 sheets (when weight 105g/m 2 paper is used) Reverse discharge Yes (*When stacker unit is installed) Power source AC100-240V, 50Hz/60Hz Environmental operating conditions Temperature 5-35°C Humidity 30-80% External measurements 365(W) x 227(H) x 575(D) mm (when paper receiver is installed 947(D) mm) Weight 17kg (excluding optional items) Noise 60dB(A)(when operating) [ ] Inside option Product specifications

(* You need an optional back-surface reading unit for double-sided reading.) Darkness levels 16 levels (internal 256 levels) Light source color infra red light (940nm) [visible red light (660nm)] Pitch (inch) 1/6”, 0.2”, 0.25”, 0.3” Marking infra red light : pencil [visible red light : pencil, ballpoint pen (black or blue)] Reading marks size: 0.5×3mm or more darkness: PCS 0.6 or darker Barcode (*Optional barcode unit is necessary to use the barcode function. The selecting "V" or "H" depends on the reading direction of the bar direction. See P90-P96) Barcode styles JAN/EAN/UPC/NW7/CODE39/CODE128/ ITF/code corresponding to the model of the device (Vertical: COOP 2 of 5, industrial 2 of 5) (Horizontal: EAN-128, CODE-93) (*As for entire thickness at time of bar-code label use 0.25 mm or less) Error detection function Sheet position detection, multiple sheet feeding detection, skew detection Printing Comes with the stacker unit PC interface USB (Ver. 2.0) 480Mbps RS-232C 9,600-115,200bps Display panel and Display panel (LCD) 20 characters x 2 lines operating switches Operating switches 5 Hopper capacity 500 sheets (paper weight 105g/m 2) Paper used Paper size IBM card size, postcard size, A5, B5, A4 8.5 inch, 9 inch Height 110-355.6mm, width 63.5-228.6mm Paper weight 84-157g/m 2 Paper quality OCR paper, bond paper, recycled OCR paper (recycled OCR paper composition 50%) Sheet feeding Feeding speed 1,100mm/s (1,000mm/s when using the barcode) Approx. 5,300 sheets/hour (single-sided using a USB connection) Sheet discharge Stacker volume Main tray: 150 sheets (when weight 105g/m 2 paper is used) Selection tray: 500 sheets (when weight 105g/m 2 paper is used) Reverse discharge Yes Power source AC100-240V, 50Hz/60Hz Environmental operating conditions Temperature 5-35°C Humidity 30-80% External measurements 800(W) x 490(H) x 365(D) mm Weight 36kg (excluding optional items) Noise 65dB(A)(when operating) [ ] Inside option Product specifications

protect it from vibration and shock during transportation. Remove the protecting tapes after placing the device in an appropriate location. 2. Install auxiliary brackets on the paper receiver. 3. Install the paper receiver on the main device. Hook tabs on the end of the paper receiver into the slits of the main device’s paper discharge side. auxiliary brackets paper receiver Protecting tapes Silica gel Protecting tapes Operation ■Preparation

5. Connect the power cord to the power outlet. Operation ■Preparation

1. Install the main tray on the main body unit. Hook the tabs on the end of the main tray into the slots on the main device’s paper discharge side. 2. Install the selection tray on the main body unit. Hook the tabs on the end of the selection tray into the slots on the main device’s paper discharge side. 3. Connect the power cord to the main device. Main tray Selection tray * When using the printer, operate P73 “ Stacker unit (printer) preparation ”

1. Turn the power on. The following message appears on the display panel (LCD). 2. OMR is initialized. 3. The motor and other components are activated to check startup conditions. 4. Check if the following message appears on the display panel (LCD). 5. When error messages may appear between steps 2 and 3, respond according to P.107(Error displays and countermeasures). Operation ■Turning power on

set to drop when the power is turned on, but if it’s still raised, press the DOWN switch in normal mode to lower the hopper. At this time, align paper carefully. Pay particular attention to the leading edges of the paper because feeding errors may occur unless the paper is properly aligned. 2. Adjust the side guide in order to close a gap between the paper and the side guide then fix it with the side guide knob.Note a large gap because mark reading becomes unstable.When moving the side guide loosen the side guide knob .Then adjust and tighten the side guide knob and fix. Note) When the side guide is pushed to seat side too much, there are times when it becomes cause of no feed error. Note) When using paper other than IBM card size, set the paper-feeding auxiliary bracket at the bottom end of the paper. Timing mark Side guide Side guide knob Paper-feeding auxiliary bracket Operation ■Loading paper

a gap and a floating on the adsorption aspect. In case of a certain pressing the panel side, make stick. 2) Because the aliging roller section has used the magnet, do not bring close a floppy disk and magnetic card etc... Aligning roller 3. To see the maximum number of cards that can be loaded into the hopper, refer to the side guide index. (A maximum of 500 sheets of 105g/m2 weight paper.) Note that overloading may result in paper not feeding, or in reading errors. Notes) 1) Carefully handle paper so that it is not bent or damaged. If bent or damaged sheets are used, paper may not feed or reading errors may occur. 2) Do not use paper in any of the following states: Soiled or damaged paper, paper to which dust or other foreign matter adheres, curled paper or folded paper (folded in two, four, etc.) 3) When adding paper, lower the hopper and be sure to reset the paper. Be sure to loosen the sheets as shown in the left figure so as to prevent double feeding when sheets adhere to each other. 4) When storing paper, avoid keeping it in a place subject to sudden environmental changes. Pay thorough attention to moisture and keep paper in a cabinet or other safe place. Do not leave paper in a dusty place such as near a window. Operation ■Loading paper

1. The device is equipped with a function to detect double-feeding (DF) errors. Conduct [Paper Weight]*1 according to the thickness of the paper to be used. *1 Setting reading (initially set to a paper weight of 105g/m 2.) See “Data reading settings ■setting paper weight” in this manual. P.44 Set the paper weight dial to prevent double feeding. Paper weight value is for reference only, so adjust it according to the condition of the paper to be used. 2. There is a mechanism which adjusts paper interval with the paper weight dial to prevent double feeding.Adjusts the paper weight dial to the sheet which you use. Note) 1.Because as for thickness of the sheet there is a variation depending upon papery quality, increase and decrease with conveying circumstance. 2.When it sets extremely small(narrow), there are case which it becomes cause of the paper clogging and the sheet skew. *2 Setting paper weight dial (initially set to a paper weight of 105g/m2.) Operation ■Setting paper weight Align the arrow to the paper weight. 1 3 5 （1 5 7 ） 1 1 0 （1 2 8 ） 9 0 （1 0 5 ） 7 2 （8 4 ） g/m2

1) Mark size: 0.5 x 3mm or more (standard mark) 2) Readable writing instruments: pencils (black, HB or darker), ballpoint pens (black or blue) 3) Readable marks: 4) Readable darkness: PCS 0.6 or darker Readable mark darkness can be adjusted. You can check mark darkness using a diagnostic utility included in the package, so check the darkness of the marks you want to read and adjust the reading setting. See “Data reading settings ■Setting min. density Level” in this manual on P.41 “Data reading settings ■Setting density balance” in this manual on P.42 Note) When using a mechanical pencil, make sure to mark with adequate darkness. Marking instructions (Good mark example) (Bad mark example)

This device is equipped with USB and RS-232C interfaces.When connecting the OMR,the connection with USB in order to show the performance of this device sufficiently is recommended. When connecting using USB, use the USB driver inside CR-ROM that came with this device. When replacing the OMR SR-600,SR-9000 series with this device, you can use the RS-232C interface. ※ 1 When using the RS-232C interface, set the same communication setting on this device and the computer. Set the computer communication setting by checking your computer or software manuals. ※ 1)There are times when it does not operate normally due to the environment of use. See the following pages to set the communication setting for this device. USB Operating mode →select( SR-3500 SR-6500mode....................P.31 Interface setting (device ID setting)................................P.32 • See P.31 and later when using USB. RS-232C Operating mode →select( SR-600 SR-9000mode....................P.33 Interface settings Setting baud rate......................................................P.34 Setting cheracter bit length.......................................P.34 Setting parity.............................................................P.35 Setting stop bit..........................................................P.36 Setting flow control...................................................P.36 Setting character code..............................................P.37 • See P.33 and later when using RS-232C. * SR-700 series can operate in SR-600 mode. Note) * Responding time to resetting command(CAN command) which is stated in the operating manual of SR-600, SR-9000 series Time after this device receiving resetting command(CAN command) ,it return ACK code is maximum approximately 5.6 seconds. * As for the details of commands of SR-600 mode please see the operating manual of SR-600 * As for the details of commands of SR-9000 mode please see the operating manual of SR-9000 Connecting to a computer

Select the SR-3500,SR6500 mode as the operating mode. (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the mode shown below. Press the FEED/ENTER switch to start [Operation Mode] setting. (“*” mark flashes in the first column of the first line on the LCD.) (3) Use the UP and DOWN switches to select the SR-3500,6500 mode. Press the FEED/ENTER switch to save the selected mode into memory. (The flashing “*” mark disappears from the LCD.) (4) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Operation mode setting values • SR-600 mode • SR-3500 mode Connecting to a computer ■USB (SR-3500) (SR-6500) (SR-3500) Operation mode setting values • SR-9000 mode • SR-6500 mode (SR-6500)

2. Interface settings (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) press the FEED/ENTER switch to begin [Device ID] setting. (“*” mark flashes in the first column of the first line on the LCD.) Set any number using the UP and DOWN switches. Device ID setting value 0-126 (4) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (5) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode.

(SR-3500) (SR-6500) ■RS-232C 1. Operating mode Select the SR-600,SR-9000 mode as the operating mode. (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the mode shown below. Press the FEED/ENTER switch to start [Operation Mode] setting. (“*” mark flashes in the first column of the first line on the LCD.) (3) Use the UP and DOWN switches to select the SR-600 mode. Press the FEED/ENTER switch to save the selected mode into memory. (The flashing “*” mark disappears from the LCD.) (4) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Operation mode setting values • SR-600 mode • SR-3500 mode (SR-3500) Operation mode setting values • SR-9000 mode • SR-6500 mode (SR-6500)

2. Interface settings 2-1. Setting baud rate (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Baud Rate] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) To continue interface setting Instead of returning to normal mode in step (6), you can continue setting various values by skipping steps (1) and (2). Baud rate setting values • 9600 • 19200 • 38400 • 57600 • 115200 2-2. Setting character bit length (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch.

and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Character bit length value • 7 • 8 2-3. Setting parity (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Parity] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Parity setting values • None • Odd • Even Connecting to a computer ■RS-232C

(1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Stop Bit] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Stop bit setting values • 1 • 2 2-5. Setting flow control (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Flow Control] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) Connecting to a computer ■RS-232C

2-6. Setting character code (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Flow control setting values • RS/CS • Xon/Xoff • None (3) Use the UP and DOWN switches to select [Character Code] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Character code setting values • Accept All • Ignore 4 Codes If ignore some is selected, the following codes are ignored. • 20H • 0AH • 7FH • 1AH Connecting to a computer ■RS-232C

This section explains how to change various sheet-reading settings. All settings can also be made using computer commands. ■Setting column Set the column. The number of columns is different depending on the reading sensor. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Setting of Column] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Column setting values 1 - maximum columns Sensor pitch Setting range Default value 1/6 inch 1-48 columns 48 columns 0.2 inch 1-40 columns 40 columns 0.25 inch 1-33 columns 33 columns 0.3 inch 1-27 columns 27 columns Note) It is necessary to set the number of columns with each operation mode. Data reading settings ■Setting column

Setting mark-reading method. There are six kinds of reading methods: “Top-end timing control type,” “Bottom-end timing control type,” “Direct under type,” “FACOM,” “Mark to mark type (without top-end margin reading),” and “Mark to mark type (with top-end margin reading).” When setting to “top-end timing control type” or “bottom-end timing control type,” you need to set a control multiple number. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Reading Method] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Reading method setting values • Control Fore • Control Back • Direct • FACOM • Mark to Mark • Mark to Mark * Data reading settings ■Setting reading method

1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Magnification] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. Magnification setting values • Top-end timing control type 1 - 9 (times) • Bottom-end timing control type 2 - 9 (times) 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Data reading settings ■Setting reading method

You can set the min. density level for this device when it is in SR-600/SR-9000 operating mode. Sensitivity levels range from 1 to 16, with level 1 being the maximum sensitivity and level 16 the lowest sensitivity. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Min. Density Level] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the MENU and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Min. density level setting values 1 - 16 *1. The above sensitivity level is a standard table under a complete marked mark of grid width for 3mm in 105g/m2 paper thickness. *2. The sensitivity level varies depending on marks because reading method is different each other. *3. When you use this device in compatible mode, the verification by you is necessary . Data reading settings ■Setting min. density level

You can set the density balance level when using the SR-600/SR-9000 operating mode. Density balance can be set so that when marks are read, marks lighter than the set density balance will be ignored, and marks darker than the set density balance will be detected. Density balance can be set from 1 to 15. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Density Balance] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) See the operating manual of each type in regard to density balance. Density balance setting values 1 - 15 Data reading settings ■Setting density balance

You can set the reading side when the optional back-sided reading unit is installed. The reading side can be set to either “single side” or “double side.” When reading single-sided sheets, if you set the reading side to “single side,” the back side won’t be read. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Reading Side] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Reading side setting values • Single Side • Double Side Data reading settings ■Setting reading side

Set detection sensitivity In the same paper weight as seat of use to detect double-feeding errors. Paper weight can be set according to the following five types: “Automatic,” “84g/m 2,” “105g/ m 2,” “128g/m 2,” and “157g/m 2.” If it’s set to “Automatic,” the device detects double-feeding errors based on the weight of first sheet read after the device is activated. Also, in case it is set to “Automatic”, if the count is set to “0”, all the information of the paper weight is cleared, and the device detects the double-feeding error based on the paper weight after the device reads the first sheet. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Paper Weight] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Paper weight setting values • Automatic • 84g/m 2 • 105g/m 2 • 128g/m 2 • 157g/m 2 Note) If it is set to “Automatic”, paper weight is detected based on the weight of the first reading sheet so that it is required to confirm if the double- feeding error, etc., does not occur. Data reading settings ■Setting paper weight

You can set paper hold setting when using SR-600 operating mode. When paper hold setting is done, after reading, without discharging the sheet you keep on the inside of this device.The processing number of cards improves with this operation.(It is the same operation as SR-3500 mode.) However It cannot maintain compatibility when the software is kept using with replacing OMR SR-600 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Paper Hold] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Data reading settings ■Paper hold setting Paper hold setting values • Not use • Use

Error detection settings for this device differ depending on the operating mode. See the following table for settings. All settings can also be made using computer commands. See “Error displays and countermeasures” in this manual on P.107-P.113. 3. Use the UP and DOWN switches to select Setting of Error Detection, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) Error detection settings 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. SR-3500 mode SR-6500 mode Default value SR-600 mode SR-9000 mode Default value Automatic paper discharge “Yes” or “No” Yes Sheet empty detection “Yes” or “No” No Timing error detection “Yes” or “No” Yes Double-feeding detection “Yes” or “No” Yes Left end skew detection “Yes” or “No” Yes Error detection settings

UP and DOWN switches to select individual error detection setting values. (See the previous table for setting values.) 5. Press the FEED/ENTER switch to save individual setting values into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Error detection settings

If you set it to use the buzzer, you can set the volume and tone. If you set it not to use the buzzer, the buzzer will not sound. ■Buzzer control 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Buzzer Control] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Buzzer control setting values • Valid • Invalid Buzzer settings ■Buzzer control

1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Buzzer Sound Adjustment] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Buzzer sound adjustment setting values 1 - 5 Buzzer settings ■Buzzer sound adjustment

setting values • Main • Select Stacker settings (when stacker unit is installed) You can set the paper discharge direction in SR-600/SR-9000 mode. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Select [Go Out Direction] setting and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Stacker settings

A character is 12 x 9 pixels. Though character height is fixed (about 3mm), widths can vary. However, the number of pixels (9 pixels) does not change, so if you enlarge a character, the space between pixels increases, making the character appear lighter. Printer settings differ depending on the operating mode. 9 pixels 12 pixels ■Printer control You can set the device to either use the printer or not use it. If you do not use the pinter function,set the invalid. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Printer Control] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. Printer control setting values • Valid • Invalid 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Printer settings ■Printer control

The width of a character can be increased in 0.8mm increments between 3.2mm and 96.0mm. (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Size] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) No. Size (a) 1 3.2mm 2 4.0mm 3 4.8mm … 115 94.4mm 116 95.2mm 117 96.0mm a About 3mm SR-3500,SR-6500 mode Character size setting....................................................P.52 Character interval setting...............................................P.53 • See P.54 and subsequent pages for SR-3500,SR-6500 mode. SR-600,SR-9000 mode Character size setting....................................................P.55 Character magnification setting.....................................P.56 Character interval setting...............................................P.57 • See P.57 and subsequent pages for SR-600,SR-9000 mode. Printer settings ■SR-3500,SR-6500 mode

3.2mm 6.4mm 2. Character interval setting The space between printed characters can be increased in 0.1mm increments between 0.8mm to 92mm. No. Interval (b) 1 0.8mm 2 0.9mm 3 1.0mm : : 911 91.8mm 912 91.9mm 913 92.0mm b (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. [Setting example 1] When the size is set at 3.2mm [Setting example 2] When the size is set at 6.4mm Character size setting values 3.2 - 96.0 (mm) 0.8mm increments (4) Use the UP and DOWN switches to set the value.

(The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. [Setting example 1] When the size is set at 3.2mm and the interval is 0.8mm. [Setting example 2] When the size is set at 6.4mm and the interval is 5.6mm. Character pitch setting values 0.8 - 92.0 (mm) 0.1mm increments 0.8mm 3.2mm 3.2mm 6.4mm 5.6mm 6.4mm (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the MENU and DOWN switches to select [Character Pitch] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the MENU and DOWN switches to set the value. Printer settings ■SR-3500,SR-6500 mode

■SR-600,SR-9000 mode 1. Character size setting The width of a character can be set in five increments. (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Size] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Character size setting values • 3.2mm • 4.0mm • 4.8mm • 5.6mm • 6.4mm a About 3mm No. Size (a) 1 3.2mm 2 4.0mm 3 4.8mm 4 5.6mm 5 6.4mm

2. Character magnification setting Width can be magnified between 1 to 15 times. Character width = size x magnification (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Magnification] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. [Setting example 1] When the size is set at 3.2mm and magnification is 1. Character width = 3.2 x 1 = 3.2mm [Setting example 2] When the size is set at 3.2mm and magnification is 2. Character width = 3.2 x 2 = 6.4mm [Setting example 3] When the size is set at 4.0mm and magnification is 2. Character width = 4.0 x 2 = 8.0mm Character magnification setting values 1 - 15 (Times) 3.2mm 6.4mm 8.0mm

The space between printed characters can be increased between 0 to 99 pixels. The actual character interval (in mm units) is determined by the “size,” “magnification,” and “interval” settings. Character interval (b) = character interval increment x (magnification + interval + 1) (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Character Pitch] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) (4) Use the UP and DOWN switches to set the value. (5) Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) (6) Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. No. Size character interval increment 1 3.2mm 0.4mm 2 4.0mm 0.5mm 3 4.8mm 0.6mm 4 5.6mm 0.7mm 5 6.4mm 0.8mm b Character pitch setting values 0 - 99 (Dots) Printer settings ■SR-600,SR-9000 mode

[Setting example 1] When the size is set at 3.2mm, the magnification is 1, and the interval is 0 pixel. Character interval = 0.4 x (1 + 0 + 1) = 0.8mm [Setting example 2] When the size is set at 6.4mm, the magnification is 1, and the interval is 5 pixels. Character interval = 0.8 x (1 + 5 + 1) = 5.6mm [Setting example 3] When the size is set at 3.2mm, the magnification is 3, and the interval is 10 pixels. Character interval = 0.4 x (3 + 10 + 1) = 5.6mm 0.8mm 5.6mm 5.6mm

You can set the barcode control in SR-3500,SR-6500 mode. ■Barcode control 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Select [Go Out Direction] setting and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Barcode control setting values • Valid • Invalid Barcode settings ■Barcode control

This device can be set to reduce power consumption in standby mode. The low-power consumption settings make the device automatically reduce power consumption when it is not used for a certain period. Sleep mode = low-power consumption condition that it automatically switches to when it is not used for a set time (sleep duration). Standby mode = a second low-power consumption condition that it automatically and continuously switches to after shifting to the sleep mode when it is not used for a set time (standby duration). (Power consumption is reduced further than sleep mode.) ■Sleep duration 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Time for Power Save] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Time for Power Save setting values • None • 1 - 60 (Minutes) *Can be set in minute increments. Low power consumption settings ■Sleep duration

MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Time for Standby] setting, and press the FEED/ENTER switch. (“*” mark flashes in the first column of the first line on the LCD.) 4. Use the UP and DOWN switches to set the value. 5. Press the FEED/ENTER switch to save the setting value into memory. (The flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) (1) Releasing Sleep/Standby mode Sleep/Standby mode will be cancelled in the following conditions. • When an operation is entered on the panel screen. • When a descending command is sent. • When an error occurs. • When loading paper on the hopper. (2) Conditions in which Sleep/Standby mode cannot be attained Sleep/Standby mode is not available in the following conditions. • When displaying a menu on the panel screen. • When an error occurs. (3) Stacker cover open error cannot be detected in Standby mode. Time for Standby setting values • None • 1 - 60 (Minutes) *Can be set in minute increments. Low power consumption settings ■Standby duration

This section explains how to display various setting information. ■Displaying the version This displays the versions of the “main body unit,” “front side reading unit,” “back side reading unit,” “stacker unit,” “printer unit,” “barcode unit” and other items. (“Back side reading unit,” “stacker unit,” “printer unit,” and “barcode unit” display only if they are installed.) Versions are displayed in a two-digit format. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Version Info.], and press the FEED/ENTER switch. Note) If “Version= @@” appears in the display,contact the store where you bought. 4. Use the UP and DOWN switches to display individual versions. 5. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Displaying various information ■Displaying the version

This displays the settings for “sensor pitch” and “sensor type” for the front side reading unit in this device. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Type of Front Reading Sensor] display, and press the FEED/ENTER switch. 4. Use the UP and DOWN switches to display the settings. Sensor pitch Sensor type Sensor pitch display • 0.2 inch • 0.25 inch • 0.3 inch • 1/6 inch Sensor type display • Infra Red • Visible Red 5. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Displaying various information ■Displaying front side reading sensor settings

This displays the settings for “sensor pitch” and “sensor type” for the back side reading unit in this device. (This display is available only when the device has a back side reading unit attached.) 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Type of Back Reading Sensor] display, and press the FEED/ENTER switch. 4. Use the UP and DOWN switches to display the settings. Sensor pitch Sensor type 5. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Sensor pitch display • 0.2 inch • 0.25 inch • 0.3 inch • 1/6 inch Sensor type display • Infra Red • Visible Red Displaying various information ■Displaying back side reading sensor settings

This displays the settings for an optional unit installed in this device. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Type of Option] display, and press the FEED/ENTER switch. 4. Use the UP and DOWN switches to display the options. Reading sensor unit Reading sensor unit display settings • Single Side • Double Side 5. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the FEED/ENTER switch to return to normal mode. Printer unit (This display is available only when the device has a printer unit attached.) Printer unit display settings • Not Cartridge • Cartridge Stacker unit (This display is available only when the device has a stacker unit attached.) Stacker unit display settings • Not Cartridge • Cartridge Barcode unit (This display is available only when the device has a barcode unit attached.) Barcode unit display • Not Unit • Vertical • Horizontal Displaying various information ■Displaying optional unit settings

This displays total count in this device. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Total count] display, and press the FEED/ENTER switch. 4. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) If when the sheet is left to the hopper the reading operation is discontinued, The actually count and error count is included in the total count because the count is not saved. Total count display 00000000~99999999 T o t a l c o u n t Displaying various information ■Displaying total count

This displays serial number of this device. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Serial number] display, and press the FEED/ENTER switch. 4. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Serial number display settings 000000000~zzzzzzzzz S e r i a l n u m b e r Displaying various information ■Displaying serial number

■Feed test 1 This test reads the check sheets included in the package to test if the device reads them properly. If the device doesn’t read the check sheets properly, the reading test will stop. Once reading of the check sheets starts, the test will continue until an error occurs or the hopper is empty. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Feed Test 1]. 4. Press the FEED/ENTER switch to confirm the selection and display [Feed Test 1]. (“*” mark flashes in the first column of the first line on the LCD.) 5. Use the UP and DOWN switches to select the setting value. 6. Press the FEED/ENTER switch to start/stop feed test 1. (The flashing “*” mark disappears from the LCD, and the test will start/stop.) 7. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) • You cannot return to normal mode while the test is running. • If a reading error occurs on both sides of a sheet, the error count will be two. • If the stacker unit is installed and an error occurs, paper will be transfered to the selection tray. Feed test 1 setting values • Stop • Start Operating tests ■Feed test 1

This test reads the check sheets included in the package to test if the device reads them properly. Even if the device doesn’t read something properly, the test will continue. Once reading of the check sheets starts, the test will continue until an error other than a reading occurs or the hopper is empty. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Feed Test 2]. 4. Press the FEED/ENTER switch to confirm the selection and display [Feed Test 2]. (“*” mark flashes in the first column of the first line on the LCD.) 5. Use the UP and DOWN switches to select the setting value. 6. Press the FEED/ENTER switch to start/stop feed test 2. (The flashing “*” mark disappears from the LCD, and the test will start/stop.) 7. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) • You cannot return to normal mode while the test is running. • If a reading error occurs on both sides of a sheet, the error count will be two. • If the stacker unit is installed and an error occurs, paper will be transfered to the selection tray. Feed test 2 setting values • Stop • Start Operating tests ■Feed test 2

be conducted only when stacker unit and printer unit are installed.) The number of characters printed varies depending on the printer settings, and character size and interval settings. Once reading of the check sheets starts, the test will continue until an error occurs or the hopper is empty. Test characters: “ ■　!”#$%&’()*+,−./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_。「」、・ ヲァィゥェォャュョッーアイウエオカキクケコサシスセソタチツテトナニヌネノハヒフヘホ マミムメモヤユヨラリルレロワン” 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Printer Test]. 4. Press the FEED/ENTER switch to confirm the selection and display [Printer Test]. (“*” mark flashes in the first column of the first line on the LCD.) 5. Use the UP and DOWN switches to select the setting value. 6. Press the FEED/ENTER switch to start/stop Printer test. (The flashing “*” mark disappears from the LCD, and the test will start/stop.) 7. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) You cannot return to normal mode while the test is running. Printer test setting values • Stop • Start Operating tests ■Printer test

This test is done when the printing of sheets is not possible, is not clear. ( This test will be conducted only when stacker unit and printer unit are installed. ) 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Printer Jet Test]. 4. Press the FEED/ENTER switch to confirm the selection and display [PJet Test Start = Start]. (“*” mark flashes in the first column of the first line on the LCD.) 5. Press the FEED/ENTER switch to do Printer jet test one time.(about 0.5 sec.) (When Printer jet test ends , the flashing “*” mark disappears from the LCD.) 6. Keep pressing the CLEAR/EXIT switch until it returns to normal mode, or press the MENU switch to return to normal mode. Note) You cannot return to normal mode while the test is running. Operating tests ■Printer jet test

■Stacker unit specifications (printer) Printing location Prints on top surface of fed sheet Printing method Inkjet Number of characters printed Maximum 72 characters (for A4-size paper) Kinds of characters printed Alphabet (uppercase and lowercase letters) Numbers (0 - 9) 36 Symbols ( !"#$%&'()*+,-./:;<=>?@［¥］^_ ■｛SP｝〜〇△□Х ) ※ 1 Japanese kana (including half and full accents, 。「」、・ー) Character size Height approximately 3mm x width approximately 3.2mm - 96.0mm Character interval Approximately 0.8mm - 92mm Printing pixels 12 vertical x 9 horizontal pixels Printing position 2mm or more from standard paper feeding edge to beginning of characters (not extened to timing mark) 2mm or more from right edge of maximum size sheet to beginning of characters Printing position adjustment Main scanning direction: Adjust head position manually. Sub scanning direction: Set print starting position command. Sub scaning direction Feeding direction ABCDEF Main scanning direction Ink cartridge Expires: 6 months after opening Life: about 1 million characters ※ 2 W L Sheet size Timing mark side Sheet feeding direction 2mm (W-4) mm (L-6) mm 3mm 3mm 2mm Sheet feeding direction Timing mark side The printable area ※ 3 ※ 1: ■in printing letter kind is printed becoming □ ※ 2:The number of letters until it stops being printed depend on working condition. ※ 3:The size of printable area depends on the size of the sheet used. Note) If a sheet is curled, it may cause a paper jam, so please do not use curly sheet. Options Stacker unit ■Stacker unit specifications

1. Turn the power off and remove the power cord from the outlet. 2. Open the front door of the stacker unit. Front door 3. Disconnect the printer connector. Connector Printer 4. Loosen the printer fixing screw to remove it. Fixing screw Options Stacker unit ■Stacker unit preparation

Note) Align positioning pins (2 places) of the ink cartridge with the positioning holes (2 places) of the cartridge case. 6. Lower the cartridge case lever to lock the ink cartridge. Align positioning pins Lever Positioning holes 7. Install the printer in the stacker unit. Options Stacker unit ■Stacker unit preparation

Fixing screw Connector Printer 9. Close the front door of the stacker unit. Front door 10. Adjust the main tray regulator to the proper paper size. 11. Connect the power cord and turn the power on. 12. Set printer control valid ( See P.51). Main tray Regulator Options Stacker unit ■Stacker unit preparation

1. Turn the power off and remove the power cord from the outlet. 2. Open the front door of the stacker unit. Front door 3. Disconnect the printer connector. Connector Printer 4. Loosen the printer fixing screw to remove it. Fixing screw Options Stacker unit ■Printing position adjustment

desired printing position, and tighten the screw to secure it. * The scale on the positioning sticker indicates the printing position from the edge of the paper. The printing position is determined by aligning the cartridge case fixing screw with the scale on the sticker. Fixing screw Cartridge case Positioning sticker 6. If the printing position is properly aligned, install the printer in the stacker unit. 7. Tighten the printer fixing screw and connect the printer connector. Fixing screw Connector Printer Options Stacker unit ■Printing position adjustment

Front door 9. Connect the power cord and turn the power on. 10. Execute printer test ( See P.70). * If the printing position is misaligned, adjust it. Fixing screw Cartridge case Positioning sticker Options Stacker unit ■Printing position adjustment

1. Open the front door of the stacker unit. 2. Open the jam release levers (4 levers) or turn the jam-removing knob to remove jammed paper. Front door Jam release levers Jam-removing knob 3. After removing jammed paper, close the jam release levers. 4. Close the front door of the stacker unit. Front door Options Stacker unit ■Clearing paper jams

(1) Make sure to tightly close the jam release levers and the front door. Loose levers or a loose door may trigger paper jams. (2) Use ink cartridges before their expiry dates. (3) Under the following conditions, remove the ink cartridge from the device, and store it at room temperature (10-35°C) in the ink cartridge storage bag included in the package. • If the main device is stored in an environment outside operating condition parameters. • If the printer will not be used for a long time (about 1 week or more). (4) Under the following conditions, defective printing (cannot print, streaked printing) may occur. • Ink cartridge is stored in environments outside of operating conditions. • The printer unit is left installed in the main device and is not used for a long time (about 1 week or more). If you have printing problems, you can try to fix them by conducting a printer jet test. If the problem doesn’t improve, the ink head may be dirty. Remove the ink cartridge and clean the ink head. Cleaning method: Wet a napless (low nap) cloth, tissue paper, or other similar item (tissue hereinafter) with water. Apply the wet tissue to the ink head for several seconds. Gently wipe the ink head. If there is any ink left on the ink head, gently wipe it off with a dry tissue. Ink head (5) This device consumes the ink little by little even when it does not print.Because it conducts extra injection automatically to prevent clogging up of ink cartridge.If you do not use the pinter function,set printer control the invalid and then remove the ink cartridge and keep. And cutting down on consuming the ink becomes possible. (6) When you do not use the printer,move the case of cartridge to almost central position of the width of the sheet you use. So It is possible to lighten the occurrence of jam. Options Stacker unit ■Stacker unit precautions for use

If you install a back side reading unit in the device, both sides of a sheet can be read. When installing the back side reading unit, set the reading side settings at the same time. See “Data reading settings ■Setting reading side” in this manual. P.43 Please see the following pages regarding confirmation of settings. See “Displaying various information ■Displaying the version” in this manual. P.62 “Displaying various information ■Displaying back side reading sensor settings” in this manual. P.64 “Displaying various information ■Displaying optional unit settings” in this manual. P.65 Options Back side reading unit

■Printer unit specifications Printing location Prints on top surface of fed sheet Printing method Inkjet Number of characters printed Maximum 72 characters Kinds of characters printed Alphabet (uppercase and lowercase letters) Numbers (0 - 9) 36 Symbols ( !"#$%&'()*+,-./:;<=>?@［¥］^_ ■｛SP｝〜〇△□Х ) Japanese kana (including half and full accents, 。「」、・ー) Character size Height approximately 3mm x width approximately 3.2mm - 96.0mm Character interval Approximately 0.8mm - 92mm Printing pixels 12 vertical x 9 horizontal pixels Printing position 2mm or more from standard paper feeding edge to beginning of characters 2mm or more from right edge of maximum size sheet to beginning of characters Printing position adjustment Main scanning direction: Adjust head position manually. Sub scanning direction: Set print starting position command. Sub scaning direction Feeding direction ABCDEF Main scanning direction Options Printrer unit ■Printrer unit specifications Ink cartridge Expires: 6 months after opening Life: about 1 million characters ※ 1 ■Pritable area Please note the printable area differs depending on the printing method. The printable area is indicated in of the following figure depending on the size of the sheet used. ※ 2 Note) If a sheet is curled, it may cause a paper jam, so please do not use curly sheet. W L Sheet size Timing mark side Sheet feeding direction

The printable area is a maximum of 230mm from the bottom edge of a sheet. [When sheet size is (L > 233)mm] 2mm (W-4) mm (L-230) mm (230-3) mm 3mm ABCD... Sheet feeding direction Timing mark side 2mm [When sheet size is (L < 233)mm] 2mm (W-4) mm (L-6) mm 3mm 3mm 2mm Sheet feeding direction Timing mark side 2. Printing while reading marks at the same time The overall area can be printed regardless of the sheet size. 2mm (W-4) mm (L-6) mm 3mm 3mm 2mm Sheet feeding direction Timing mark side ※ 1:The number of characters until it stops being printed dpend on working condition. ※ 2:The size of printable area depends on the size of the sheet used. Options Printrer unit ■Printable area

1. Turn the power off and remove the power cord from the outlet. 2. Remove the carrier cover. 3. Lift the cartridge case lever and insert an ink cartridge. Note) Align positioning pins (2 places) of the ink cartridge with the positioning holes (2 places) of the cartridge case. 4. Lower the cartridge case lever to lock the ink cartridge. Carrier cover Lever Positioning holes Align positioning pins Options Printrer unit ■Printer unit preparation

1. Turn the power off and remove the power cord from the outlet. 2. Remove the carrier cover. Carrier cover 3. Loosen the cartridge case fixing screw, move the cartridge case according to the desired printing position, and tighten the screw to secure it. * The scale on the positioning sticker indicates the printing position from the edge of the paper. The printing position is determined by aligning the cartridge case fixing screw with the scale on the sticker. Fixing screw Cartridge case Positioning sticker 4. Connect the power cord and turn the power on. 5. Set printer control valied ( See P.51). Options Printrer unit ■Printing position adjustment

* If the printing position is misaligned, loosen the cartridge case fixing screw, adjust the cartridge case according to desired printing position, and tighten the screw to secure it. Fixing screw Cartridge case Positioning sticker 7. If the printing position is properly aligned, close the carrier cover. Carrier cover Note) If the cartridge case is difficult to move, grasp it by the top part of the case. Cartridge case Options Printrer unit ■Printing position adjustment

(1) Use ink cartridges before their expiry dates. (2) Under the following conditions, remove the ink cartridge from the device, and store it at room temperature (10-35°C) in the ink cartridge storage bag included in the package. • If the main device is stored in an environment outside operating condition parameters. • If the printer will not be used for a long time (about 1 week or more). (3) Under the following conditions, defective printing (cannot print, streaked printing) may occur. • Ink cartridge is stored in environments outside of operating conditions. • The printer unit is left installed in the main device and is not used for a long time (about 1 week or more). If you have printing problems, you can try to fix them by conducting a printer Jet test. If the problem doesn’t improve, the ink head may be dirty. Remove the ink cartridge and clean the ink head. Cleaning method: Wet a napless (low nap) cloth, tissue paper, or other similar item (tissue hereinafter) with water. Apply the wet tissue to the ink head for several seconds. Gently wipe the ink head. If there is any ink left on the ink head, gently wipe it off with a dry tissue. Ink head (4) Always turn the power off when exchanging ink cartridge because it can cause trouble. (5) This device consumes the ink little by little even when it does not print.Because it conducts extra injection automatically to prevent clogging up of ink cartridge.If you do not use the pinter function,set printer control the invalid and then remove the ink cartridge and keep. And cutting down on consuming the ink becomes possible. (6) Please do not open the cover while in the initializing or operation for the device. The Ink fly in the device, it will cause ink fly and it will put the stain. Options Printrer unit ■Printer unit precautions for use

If you install a barcode unit in the device, barcodes on paper can be read. ■Barcode unit specifications Barcode unit / V (vertical feeding) Reading direction Vertical feeding (bars are parallel to sheet feeding direction) Codes JAN/EAN/UPC (module 0.33 mm,0.8 times~ 2 times) NW-7 CODE-39 CODE-128 ITF Industrial 2 of 5 COOP 2 of 5 * The unit can be set to read up to four kinds of codes. Reading area Sheet feeding direction: 10mm from the front edge of a sheet to 10mm from the rear edge of a sheet Paper width direction: ±30mm of 50-200mm from standard paper feeding edge. Number of digits to be read Maximum 32 digits (total number of digits to be read is 150 or less) (For CODE-128, a maximum of 64 digits if the starting character is CODE-C) Number of labels to be read Maximum 10 (1 sheet) Label interval 15mm or more Barcode printing specifications • Length 60mm or less X height 10mm or more (For narrow bars with widths of 0.19mm or less, use coated labels less than 40mm long ※ 1) * Barcode length requires a quiet zone (margin) more than 2.54mm on both sides or 10 times the width of the narrow bar, whichever is bigger. • PCS: 0.7 or more (light-source wavelength: 633nm) • Bar width (narrow bar) 0.125-1mm * Bar:space ratio = 1:0.85-1.15 * Recommended N:W ratio = 1:2.5 * There should not be any bleeding, chipping, blank areas, etc. • Skew: ±5 degrees or less from the standard paper feeding edge. * If narrow bar width is 0.19mm or less, ±2 degrees or less. Reading side Read the top surface of a sheet as it is fed Directions to adjust reading positions Paper width direction: manually adjust the head position Sheet feeding direction: “Specifying reading start position mode” Use command to specify reading starting position from the front edge of a sheet and reading width for number of barcodes. “Whole area reading mode” Entire area of a sheet can be read. (Barcodes in all areas of the sheet-feeding direction can be read.) ※1 entire thickness of label sticking section is 0.25mm or less Label must not be floated and come off. Barcode unit / V • barcode unit / H ■Barcode unit specifications

Reading direction Horizontal feeding (bar direction is perpendicular to sheet feeding direction) Codes JAN/EAN/UPC (module 0.33 mm,0.8 times~ 2 times) NW-7 ITF CODE-39 CODE-93 CODE-128 EAN-128 Reading area Sheet feeding direction: 12mm from the front edge of a sheet to 65mm from the rear edge of a sheet Paper width direction: 20mm from timing mark size to 224mm (centered on the sensor) Number of digits to be read Maximum 48 digits Number of labels to be read Maximum 10 (total number of digits to be read is 200 or less) Label interval 40mm or more Barcode printing specifications • Height 10mm or more * It requires a starting margin of 12mm or more, and an ending margin of 4 characters or more for a barcode. • PCS: 0.7 or more • Bar width (narrow bar) 0.2-2mm * Bar:space ratio = 1:0.85-1.15 * Recommended N:W ratio = 1:2.5 * There should not be any bleeding, chipping, blank areas, etc. • Skew: ±3 degree or less from the standard paper feeding edge. • Sticking label: ※ 1 Reading side Read the top surface of a sheet as it is fed Directions to adjust reading positions Paper width direction: manually adjust the head position Sheet feeding direction: “Specifying reading start position mode” Use command to specify reading starting position from the front edge of a sheet (measurement: mm) and reading area for a barcode. “Whole area reading mode” Entire area of a sheet can be read. (Barcodes in all areas of the sheet-feeding direction can be read.) “SR9000 compatible mode” Specify barcode reading starting position using timing mark ※1 entire thickness of label sticking section is 0.25mm or less Label must not be floated and come off. Barcode unit / V • barcode unit / H ■Barcode unit specifications

The barcode readable area differs depending on the kind of barcode unit. 1. Barcode unit / V (vertical feeding) 0mm 50mm Timing mark side 200mm 0mm 10mm 15mm or more 65mm or more (when stacker unit is not installed) 10mm or more (when stacker unit is installed) Sheet feeding direction Center of barcode Center of barcode Clear area Clear area Clear area Reading area Barcode interval Height of barcode 10mm or more Narrow bar width 0.19mm or more: height 60mm or less Narrow bar width 0.19mm or less: height 40mm or less Clear area Reading width 80mm Center of barcode Note) Adjust the barcode center when reading a number of sheets .In addition when it makes the barcode adjoin which is not read, do not make it go into reading area. Barcode unit / V • barcode unit / H ■Barcode readable area

0mm 20mm 224mm 0mm 12mm 40mm or more 10mm or more 65mm or more Clear area Clear area Clear area Clear area Reading area Sheet feeding direction Timing mark side Height of barcode 10mm or more Horizontal direction deviance 2mm or less Barcode front edge margin 12mm or more Barcode rear edge margin 4 characters or more Barcode unit / V • barcode unit / H ■Barcode readable area

1. Turn the power off. 2. Remove the carrier cover. Carrier cover 3. Loosen the barcode unit position fixing screw, move the barcode unit according to barcode position, and tighten the screw to secure it. * The scale on the positioning sticker indicates center of the barcode position from the edge of the paper(Timing mark side). The barcode position is determined by aligning the barcode unit position fixing screw with the scale on the sticker. 4. Turn the power on. 5 0 1 0 0 1 5 0 2 0 0 ( m m ) Positioning screw Positioning sticker Barcode unit Barcode unit / V • barcode unit / H ■Barcode reading position adjustment

* If a reading error occurs, the barcode reading position may be misaligned, so make an adjustment. 6. If the barcode reading position is properly aligned, close the carrier cover. Carrier cover 5 0 1 0 0 1 5 0 2 0 0 ( m m ) Positioning screw Positioning sticker Barcode unit Barcode unit / V • barcode unit / H ■Barcode reading position adjustment

(1) When applying barcode stickers, etc. on a sheet, make sure that sheet thickness with stickers is 0.25mm or less. (2) When applying barcode stickers, etc. on a sheet, avoid the grayed area below. (3) Make barcodes according to the following specifications and guidelines. • AIM USS (Automatic Identification Manufacturers barcode symbol specifications) • JIS JIS X 0501 Barcode symbols for common product codes JIS X 0502 Barcode symbols for logistic product codes JIS X 0503 Barcode symbol NW-7 and code 39 basic specifications (4) Faded, chipped, and bleeding barcodes cannot be read. Please note that barcodes printed with low-resolution printers such as dot-matrix printers and inkjet printers tend to have similar results. (5) If the sensor area becomes dirty with paper powder, use a soft cloth, a cotton swab, or similar materials soaked with plastic cleaner, or use a cloth for glasses to wipe it. 65mm Sheet feeding direction Timing mark side Barcode unit / V • barcode unit / H ■Barcode unit precautions for use

regularly using the following procedures. Cleaning intervals differ depending on usage conditions (usage frequency, quality of paper used, etc.) Cleaning periods are for your reference -- clean the device soon if you notice dirt or other irregularities. Cleaning Warning ● WHEN CLEANING THE DEVICE , DO NOT SPRAY ANY MATERIALS CONTAINING AN INFLAMMABLE GAS OR LIQUID AND BE SURE TO KEEP THIS KIND OF MATERIALS AWAY FROM THIS DEVICE. Use a cleaning cloth with suitable amount of cleaning liquid to wipe off well, after removing the power plug from the outlet and the device becomes to cool off. ● WHEN CLEANING THE DEVICE , BE SURE TO REMOVE THE POWER PLUG FROM THE OUTLET. There is a threat that a fire or an electric shock cause the unexpected accident. ■Cleaning procedures Main body unit 1. Turn the power off and remove the power cord from the outlet. 2. Grasp the lock lever to release the lock, and push the top cover up to open it. 3. The screw of a right figure arrow is loosened, a stopper is slid rightward, and it is made a release position. Top cover comes to open greatly. Caution) If you do not remove the stopper, you may damage the product. 4. Clean necessary parts. 5. After cleaning slides a stopper leftward and tightens a screw. Warning) If a stopper is not returned to the original position, fingers and other body parts could be pinched and injured by the back hinge.by the back hinge. 6. Close the top cover. Slowly close the top cover and press it until there is a click sound that indicates it is locked. Stopper Screw

carbon paper, wipe the rollers softly with a clean cloth slightly wetted with disinfectant alcohol (ethanol). * If the rollers are stained, the stains may rub off on cards or other various malfunctions may occur. (2) Cleaning reading lens Clean the reader lens by softly wiping it with a clean cloth slightly wetted with disinfectant alcohol (ethanol) once a month or every 5,000 sheets. * If the reading lens is stained, reading errors may occur. (3) Cleaning various sensors Softly wipe the sensors with a clean cloth slightly wetted with disinfectant alcohol (ethanol) once a month or every 5,000 sheets. Use air blow etc. when cleaning the left skew sensor section. *If the sensors are stained (with paper powder, etc.) detection errors may occur. Hopper sheet 0 detection sensor Paper-feeding roller Aligning roller

Cleaning ■Cleaning procedures Driving rollers Slave rollers Slave rollers Slave rollers Slave rollers Paper discharge roller Selected paper discharge sensor Main paper discharge sensor Printing start sensor Slave rollers Reading lens Back surface reading sensor (option) Double-feeding prevention roller / top Double-feeding prevention roller / bottom (under the cover) Reading start detection sensor Driving rollers Reading lens Front surface reading sensor Left skew sensor Clearing

1. Turn the power off and remove the power cord from the outlet. 2. Open the front door of the stacker unit. Front door 3. Open the jam release lever. 4. Clean necessary parts. Jam release lever Cleaning ■Cleaning procedures

6. Clean the remaining three parts in the same manner as in steps 3 to 5. Jam release lever 7. Close the front door of the stacker unit. Front door Cleaning ■Cleaning procedures

See the following table, and contact us, or the store where you purchased the device, when requiring component replacement. Main body unit * Replacement periods may differ depending on usage conditions (usage frequency, quality of paper used, etc.) Component name Number Replacement reference (counter number) Remarks Paper-feeding roller 1 100,000 or 3 years - Double-feeding prevention roller / top 1 100,000 or 3 years Replace at the same time as double-feeding prevention roller / bottom Double-feeding prevention roller / bottom 1 100,000 or 3 years Replace at the same time as double-feeding prevention roller / top Aligning roller 1 100,000 or 3 years - Driving roller / A 4 500,000 or 3 years - Driving roller / A Double-feeding prevention roller / top Double-feeding prevention roller / top Paper-feeding roller Aligning roller Service schedule