CSI Controls CS1200 Setup Manual

Setup Manual Before You Begin Mount and wire your alarm according to installation instructions. NOTE: • Cellular WiFi hotspots are not recommended for use with � � this�WiFi�alarm,�as�intermittent�or�unreliable�notification�� service can result. • WPA2 Security must be enabled on the wireless router for WiFi connections. This setup manual covers setup using a WPS connection to your wireless network, a wired ethernet connection and setup on a wireless network that does not have the WPS function. Refer to the appropriate section for the type of setup required. Requirements: WiFi Setup using WPS (WiFi Protected Setup) • CS1200 WiFi Alarm • Wireless Router With WPS Functionality Note: WPA2 Security must be enabled on the wireless router • Smart Phone, Tablet, Laptop, or Desktop Device WiFi Setup Without WPS (WiFi Protected Setup) Functionality • CS1200 WiFi Alarm • Wireless Router With An Unused LAN Port Note: Wireless Router SSID and Security Key Required to Complete WiFi Setup Note: WPA2 Security must be enabled on the wireless router • Ethernet Cable (must reach from router to alarm) • Ethernet Cable (must reach from router to alarm) • Smart Phone, Tablet, Laptop, or Desktop Device Wired Ethernet Setup • CS1200 WiFi Alarm • Internet Modem, Router, or Ethernet Switch With An Unused LAN Port • Ethernet Cable (must reach from router to alarm) • Smart Phone, Tablet, Laptop, or Desktop Device INDOOR ALARM SYSTEM 120 VAC CS1200 WiFi Replace battery yearly 1

1. Plug in the CS1200 WiFi Alarm power cord into a 120V receptacle. 2. Press the WPS button on your wireless router (often on the back side of router). 3. Press the WPS button on the CS1200 WiFi � Alarm�(the�blue�network�status�light�will�flash�� continuously). The blue network status light will illuminate steadily when the CS1200 WiFi Alarm is successfully connected to the wireless network. STEP 1: Ethernet Network and Non-WPS WiFi Network Setup 1. Connect an Ethernet cable (not supplied) from the CS1200 WiFi Alarm Ethernet port to a unused network router LAN port. 2. Plug the CS1200 WiFi Alarm power cord into a 120V receptacle. 3. The CS1200 WiFi Alarm will automatically detect the Ethernet network and connect upon power up. The blue network status light will illuminate steadily when the CS1200 WiFi Alarm is successfully connected to the Ethernet network. 2 POWER WPS INTERNET INDOOR ALARM SYSTEM 120 VAC CS1200 WiFi Replace battery yearly INDOOR ALARM SYSTEM 120 VAC CS1200 WiFi Replace battery yearly INDOOR ALARM SYSTEM 120 VAC CS1200 WiFi Replace battery yearly INDOOR ALARM SYSTEM 120 VAC CS1200 WiFi Replace battery yearly

1. After the alarm is successfully connected to the network, allow 2 minutes before proceeding. 2. Using your internet connected device (i.e. Laptop, Desktop, etc.), open a new web browser window or tab. Note: you must be connected to the same router as your CS1200 WiFi Alarm. 3.��Type�the�following�into�the�address�field�at�the�top�of�your�web�browser:� � www.mywifialarm.com or scan QR Code. 4. Follow the registration link. 5. After reading and accepting the terms of the CS1200 WiFi Alarm, enter your alarm’s Unit ID# located on the back of the battery compartment cover. (DO NOT ENTER THE COLONS). Click�Configure. 6. If the CS1200 WiFi Alarm has not been � verified,�you�will�be�required�to�enter�an�email � address�to�receive�a�verification�link.�Enter�� � � your email address and press the REQUEST VERIFICATION button. Note:�All�future�alarm�notifications�will�be�sent�to�� � � this�verification�email�address�in�addition�� � � to the email addresses entered on the CS1200 WiFi Alarm’s setup page. 7.�� An�email�will�be�sent�to�the�verification�email�� � � address�entered�with�a�link�to�the�Notification�Setup�� � page.�Click�this�link�to�access�the�Notification�Setup�� page. This email must be received and opened by the same device used for the steps above. 8. If the CS1200 WiFi�Alarm�has�already�gone�through�the�verification�process,�the�web�� � � � browser�will�immediately�be�redirected�to�the�Notification�Setup�page. 3 WARNING! USE ALKALINE BATTERY ONLY, NON-ALKALINE BATTERY MAY REDUCE PRODUCT PERFORMANCE UNIT ID# A1B5:C3D2:E7C2

WPA2 Security Key No Security Device Name Email Address 1 Email Address 2 Text Message Phone Number 1 Text Message Phone Number 2 Notification Setup Submit IP Address: 10.4.150.148 MAC Address: A1:B5:C3:D2:E7:C2 Battery Status: None (Hit F5 to refresh) At least one email address or one phone number must be provided to receive notification messages. Example: 123-456-7890 Example: 123-456-7890 STEP 3: Alarm Notification Setup 1. On the CS1200 WiFi Alarm setup � page,�fill�in�the�appropriate�data: Note: Steps a. and b. are only required if connecting to a wireless network that does not support WPS connection. a.��Network�Name�(SSID):�Enter�the�� wireless router’s network name, also called SSID, as it appears on the WiFi connection for your Smart Phone, Tablet, Laptop, or Desktop Device. b.�WPA2�Security�Key:�Enter�the�� � wireless router’s security key (password). Or Check the “No Security” box if the wireless network does not require a password. c.� Device�Name:�Enter�a�unique�device�name�for�each�CS1200 WiFi Alarm being installed. EXAMPLE: “Cabin Sump Alarm”. Maximum 30 characters including spaces. d.� Email�Address(es):�Fill�in�the�email�address(es)�which�will�be� receiving�notifications�from�the�� CS1200 WiFi Alarm. e. Enter the phone number of the device (or devices) that will receive the text messages. Note: A minimum of one email address or text message phone number must be entered to � receive�alarm�notifications. 2.�� Click�Submit�button�to�save�your�notification�data. 3. If connecting to a wireless network that does not support WPS connection, enter the router’s Network Name (SSID) and WPA2 Security Key, then disconnect the ethernet cable. Remove the backup battery and disconnect the power cord from the power receptacle. Once the green power light is no longer illuminated, plug the power cord back into the power receptacle. The blue network status light will illuminate steadily when the CS1200 WiFi Alarm is successfully connected to the wireless network. INDOOR ALARM SYSTEM 120 VAC S1200 WiFi Replace battery yearly

1. Press and release the “TEST” button on the CS1200 WiFi Alarm. The alarm horn will sound and the alarm light will activate while the “TEST” button is being held. 2.�� Verify�that�an�alarm�notification�is�received�via�all�entered�email�or�text�numbers. Note: It may take several minutes for the message to appear in your email inbox or message folder, depending�upon�email�server�traffic�or�other�circumstances.�If�you�have�not�received�a�notification� within 5 minutes, verify the email address and/or cellular phone information is entered correctly and that�any�email�filters�are�set�to�allow�messages�from�[email protected]. While using a WiFi connection, a signal strength rating will also be sent with the alarm and power restored�notifications.� 5.0 - 10.0 Great! 3.0 - 4.9 Good. No signal loss is expected. 2.0 - 2.9 Marginal. You may experience occasional signal loss. 0.0 - 1.9 Weak. Move alarm closer to wireless router. 5

• One Flash Every Five Seconds: No WiFi can be found. Verify wireless router is powered and functioning. Verify alarm is within range of wireless router. • Two Flashes Every Five Seconds: An IP address cannot be obtained. Cycle the power to your wireless router. Enable DHCP in your router set up (see router manufacturer’s users manual). • Three Flashes Every Five Seconds: Email is unable to be sent. Verify the internet connection is functioning. Verify the email address is valid. Alarm webpage is not found: • Alarm is not connected to a wireless network. Connect to the wireless network according to the setup instructions. • Your internet connected device (laptop, desktop, tablet, smartphone, etc.) is not connected to the same wireless network as the alarm. Connect your device to the same wireless network as the alarm. •� The�correct�Unit�ID#�was�not�entered�into�the�browser:�www.mywifialarm.com. Re-enter the correct Unit ID# for your alarm. Notification emails or text messages are not received: • Email address or cellular information was not set up correctly. Verify email addresses are valid and/or cell numbers are entered correctly. • Internet access is not functioning. Repair the internet connection. •� Notification�email�has�been�blocked.�Unblock�or�allow�emails�from� [email protected] in your email account. • The CS1200 WiFi Alarm terms and conditions have not been accepted and/or � a�verification�email�has�not�been�sent.�Follow�steps�in�the�“Verification”�section. Congratulations! Your CS1200 WiFi Alarm is�now�configured�and�ready�to�be�used. (Remember to test your alarm on a regular basis to ensure proper operation) ©CSI Controls 1047750A 07/16