Munters MCS300 Operation & User’s Manual

Originalinstructions Usermanual MCS300 0 1 Desiccantdehumidifier 190TEN-1027-F1404 © MuntersEuropeAB2014 ...

dehumidificationof air. Any otheruse of the unit, or use whichis contrary tothe instructions giveninthis manual, cancause personalinjury anddamage tothe unit andotherproperty. Nomodificationof the unit is allowedwithout prior approvalby Munters. Attachment orinstallation of additionaldevices is only allowedafterwritten agreement by Munters. Warranty The warranty periodis validfromthe date the unit left ourfactory, unless otherwise statedinwriting. The warranty is limitedtoafree exchange of parts or components whichhave failedas aresult of defects in materials orwork ...

..................... 1 1.2 Unintendeduse ........................ 1 1.3 Safety .................................. 2 1.4 Marking ................................ 3 2 Function overview .......................... 4 3 Installation .................................. ...

anduse the dehumidifierinasafe andefficient way. Readthroughthe manualbefore the dehumidifieris installedandused. Contact yournearest Munters office if you have any questions regarding the installationorthe use of your dehumidifier. This manualmust be storedinapermanent locationclose tothe dehumidifier. 1.2 Unintended use ■ The dehumidifieris not intendedforoutdoorinstallation. ■ The dehumidifieris not intendedforuse inclassifiedareas where explosionsafety compliant equipment is required. ■ The dehumidif ...

safety requirements of the directives andstandards listedinthe ECDeclarationof Conformity. The informationinthis manualshallinnoway take precedence overindividualresponsibilities orlocal regulations. During operationandotherwork withamachine it is always the responsibility of the individualtoconsider: ■ The safety of allpersons concerned. ■ The safety of the unit andotherproperty. ■ The protectionof the environment. The types of dangers that are indicatedinthis manualare describedinsectionImportantuserinformation. W W WARNING! ARN ...

Fabr. No 1~50Hz 230V 0.2 kW 1.9 kW Max 2.1kW Munters Europe AB Tobo Sweden M INCENTIVE GROUP Figure 1.1 Identificationlabel position Type Fabr. No. 0919 190XXX XXXXX 1 ~ 230V 50 Hz 0,2 kW Max 2,1 kW Munters Europe AB Isafjordsgatan 1 164 26 Kista, Sweden M IP44 Fabr. year 1,9 kW Made in Sweden Weight: 25 kg MCS300 2009 Figure 1.2 Identificationlabel 3 Introduction 190TEN-1027- F1404 ...

comprisedof alarge numberof smallairchannels. The desiccant rotoris made of acomposite materialthat is highly effective inattracting andretaining water vapour. The rotoris dividedintwozones. The airflow tobe dehumidified, process air,passes throughthe largest zone of the rotorandthenleaves the rotoras dry air. Since the rotorrotates slowly, the incoming air always meets adry zone onthe rotor, thus creating acontinuous dehumidificationprocess. The airflow that is usedtodry the rotor, reactivationair, is heated. The reactivationairpass ...

surface. If the unit is storedpriortoinstallation, place it inaroofedarea, onalevelsurface where it is protectedfromimpact, dust, frost, rainoraggressive contaminants. 3.2 Safety W W WARNING! ARNING! ARNING! Theunit is not intendedforuseinclassifiedareas whereexplosionsafety equipment is required. W W WARNING! ARNING! ARNING! Theunit must not besplashedwith, orimmersedinwater. W W WARNING! ARNING! ARNING! Donot covertheunit orobstruct theairvents. W W WARNING! ARNING! ARNING! Donot operatetheunit if thepowerplugorcordis dam ...

3.3 Inspection ofdelivery 1. Inspect the delivery andcompare withthe delivery note, orderconfirmationorotherdelivery documentation. Make sure that everything is includedandnothing is damaged. 2. Contact Munters immediately if the delivery is not complete inordertoavoidinstallationdelays. 3. If the unit is tobe put intostorage priortoinstallation, see sectionStoring the equipment. 4. Remove allpackaging materialfromthe unit, andmake sure that nodamage has occurredduring transportation. 5. Any visible damage must be reportedinwriting toMunters w ...

■ Place the dehumidifierinanupright positiononahorizontalsurface. ■ Re-use the packaging materialtoprovide protectionforthe unit. ■ Protect the dehumidifierfromphysicaldamage. ■ Store the dehumidifierundercoverandprotect it fromdust, frost, rainandaggressive contaminants. 3.7 Siterequirements The dehumidifieris only intendedforindoorinstallation. Avoidinstalling the dehumidifierwhere there is a risk of waterentering the unit, orinavery dusty environment. RefertoMunters foradvice if indoubt. Forunit andservice dimensions, see section10 ...

3.8.1 General Follow the instructions below whenattaching ducts orflexible hoses tothe unit's airconnections. ■ Duct lengthshouldbe kept as short as possible tominimise static pressure loss. ■ Allduct andhose connections must be airtight andvapourtight toensure fullperformance. ■ Toretainthe correct airflow forreactivationair, anairdampermust be installed. This damperis tobe installedinthe wet airoutlet ducting, see Figure 3.2 andFigure 3.3 . Foradjustment of airflow, follow the instructions insection4.5, Adjusting reactivationtemperature. ■ Ducting forwet airshallbe installedat adownwardincline toenable c ...

space tobe dehumidifiedandthe wet airis dischargedinthe vicinity of the unit ormovedoutdoors, see Figure 3.3 . The installationis usedtosolve the following problems: - Whenmoisture damagedobjects are tobe dehumidified. - Dust orcorrosioncausing particles are present inaspace where dry airwillbe supplied. - Toprevent moisture fromentering the dehumidifiedspace/object. 0 1 A B G E F D C Figure 3.3 Installationinanopenairflowsystem A. Dryair E. Wet air B. Processair F. Reactivationair C. Connectionfitting 1) G. Connectionfitting 2) D ...

3.10.1 General The connectionsocket forthe humidistat is locatedinthe storage compartment forthe power cable, see Figure 3.4 . The appropriate plug forthe humidistat is deliveredwiththe unit, see section 3.10.2, Humidistatconnectionkit. The humidistat shallbe mounted1–1.5 m. above the floorandpositionedso that it is not exposeddirectly todry airfromthe unit orincoming moist airfromopening andclosing doors. It shouldnot be placedclose toaheat source, orsothat it is exposedtodirect sunlight. The humidistat shall be asingle stage humidistat andconnectedsothat the controlling circuit closes as relative humidity increa ...

Follow the instructions below toassemble andconnect the humidistat connectionkit. 1. Connect the leads topins 1 and2, andthe screentothe earthpin. 1 3 2 A B Figure 3.5 Connectionof leads A. Leadconnections B. Screenconnections 2. Affixthe terminal(2) tothe plug (1). 3. Tightenthe terminalscrews (3). 4. Affixthe cover(4) tothe plug (1). 5. Affixthe flange (5) tothe cover(4). 1 2 3 4 5 3 Figure 3.6 Humidistatconnectionkitassembly 11 Installation 190TEN-1027- F1404 ...

Man: The dehumidifier’s fans, rotorandreactivationheateroperate continuously. Auto1: The dehumidifier’s fans, rotorandreactivationheaterare started/stoppedby the humidistat. Auto2: The dehumidifier’s fans androtoroperate continuously. The reactivationheateris startedand stoppedby the humidistat only. This mode of operationis usedtomaintainaircirculation. If relative humidity rises tothe humidistats setpoint, the reactivationheaterstarts. The reactivationheaterstops when relative humidity drops below the setpoint. NOTE! ForthedehumidifiertofunctioninAuto1and ...

C. Measurement selector D. Operatingmodeselector The following parameterinformationis displayedonthe controlpanel: Totaloperatingtime KWH Powerconsumptionduringaspecificperiod Temp Reactivationtemperature Change the parameterdisplay by pressing the measurement selectorbuttononthe controlpanel. Measurement of powerconsumptioncanbe reset before eachdehumidifying occasionorperiodof use. Toreset the measurement: 1. Switchoff the unit 2. Press boththe Measurement andOperating Mode Selectors at the same time andthenswitchthe unit On(positionI) while stillpressing ...

2. Switchthe on-off switchtopositionI, see Figure 4.1 . 3. Select the Manoperating mode by pressing the operating mode selectorbutton. 4.3.3 Automaticoperation Forthe dehumidifiertooperate inAuto1 or2,the humidistat must be connectedtothe humidistat socket of the unit, see section3.10, Connecting the humidistat. 1. Reset measurement of powerconsumptionas required, see section4.3.1, Measuredvalues. 2. Adjust the humidistat tothe desiredsetpoint. 3. Switchthe on-off switchtopositionI, see Figure 4.1 . 4. Select the Auto1 or2 operating mode ...

-Remove the mains plug fromthe socketbefore starting anymaintenance work. The dehumidifieris designedforcontinuous use overalong periodof time withaminimalamount of supervision. Undernormaloperating conditions, maintenance requirements are minimal. The service intervaldepends mainly onthe operationalconditions andworking environment. NOTE! It is recommendedtocontact Munters forserviceorrepair. Operatingfaults canoccurif theunit is maintainedinsufficiently orincorrectly. Munters Service canofferaservice planadaptedtosuit the condi ...

1. Toremove the filter, slide the filtergrating upwards, thendownwards andout according toFigure 5.1 . 2. Cleanfilterhousing andgrating before fitting the new filter. 190TEN-1027- F1404 Serviceand maintenance 16 ...

problems. 6.2 Safety W W WARNING! ARNING! ARNING! Always unplugthedehumidifierbeforeany maintenanceorrepairwork is carriedout. Incaseof afixedinstallation wheretheplugis beingreplacedby acircuit breaker, thepowermust beswitchedoff andthecircuit breakerlocked. W W WARNING! ARNING! ARNING! Theunit must not beconnectedtoothermains thanspecifiedontheunits identificationplate. W W WARNING! ARNING! ARNING! Adjustments, maintenanceandrepairs must only becarriedout bytrainedandqualifiedpersonnel. W W WARNING! ARNING! ARNING! Duet ...