Toro 3678 Operator's Manual

Reelmaster® 5610 Traction Unit Model No. 03678—Serial No. 316000001 and Up Register at www.Toro.com. Original Instructions (EN) *3398-608* A ...

For details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other r ...

Safe Operating Practices........................................... 4 Toro Riding Mower Safety ........................................ 6 Sound Power Level.................................................. 7 Sound Pressure Level............................................... 7 Vibration Level ...................................................... 7 Safety and Inst ...

EN ISO 5395:2013 and ANSI B71.4-2012 and meets or exceeds these standards when equipped with rear weight; refer to the procedure for Installing Rear Weights in the Setup section. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means Caution, W ...

attachment clutches, shift into neutral, and engage the parking brake. • Stay alert for holes in the terrain and other hidden hazards. • Watch out for traffic when crossing or near roadways. • Stop the blades rotating before crossing surfaces other than grass. • When using any attachments, never direct discharge of material toward bystanders nor allow anyone near the machine while in op ...

brake, stop engine and remove key from ignition. Wait for all movement to stop before adjusting, cleaning, or repairing. • Clean grass and debris from cutting units, drives, silencers/mufflers, and engine to help prevent fires. Clean up oil or fuel spills. • Use jack stands to support components when required. • Carefully release pressure from components with stored energy. • Disconnect bat ...

basis. Tighten or repair them as needed. • If the engine must be running to perform a maintenance adjustment, keep hands, feet, clothing, and any parts of the body away from the cutting units, attachments, and any moving parts. Keep everyone away. • To ensure safety and accuracy, have your Toro Distributor check the maximum engine speed with a tachometer. Maximum governed engine speed should ...

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7272 1. Cutting/dismemberment hazard; fan—stay away from moving parts. 93–6696 1. Stored energy hazard—read the Operator's Manual. 106-6754 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay aw ...

maintenance. 2. Cutting hazard of hand or foot—stop the engine and wait for moving parts to stop. Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chem ...

2. Power point—10 A 3. Headlights—10 A 4. Power—10 A 5. Engine start—15 A 6. Optional air ride seat suspension—20 A 7. Engine computer management C—7.5 A 8. Engine computer management B—7.5 A 9. Engine computer management A—7.5 A 110-8869 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 2. Thrown object hazard—keep bystanders a safe distance from the mac ...

Procedure Description Qty. Use 1 No parts required – Adjust the tire pressure. 2 No parts required – Adjust the control-arm position. Front hose guide, right 1 3 Front hose guide, left 1 Install the cutting units 4 No parts required – Adjust the turf-compensation spring. 5 Rear weights (size varies with configuration). Varies Install the rear weights (order from your To ...

Position No Parts Required Procedure Adjust the position of the control arm as desired. 1. Loosen the 2 bolts securing the control arm to the retaining bracket (Figure 2). Figure 2 1. Control arm 3. Bolts (2) 2. Retaining bracket 2. Rotate the control arm to the desired position and tighten the 2 bolts. 3 Installing the Cutting Units Parts needed for this procedure: 1 Front hose guide, right 1 Front hose guide, left Procedure 1. ...

2. Rod bracket D. Mount the rod bracket to the cutting unit tabs with the carriage bolts and nuts (Figure 5). Important: On cutting unit 4 (left front) and cutting unit 5 (right front), use the rod-bracket mounting nuts to install the hose guides to the front of the cutting-unit tabs (Figure 6 and Figure 7). Position the hose guides so that they lean toward the center cutting unit (Figure 7 and Figure 8). Figure 6 1. ...

the lift arm while inserting the carrier-frame shaft up into the lift-arm-pivot yoke (Figure 10). Figure 10 1. Lift arm 3. Lift-arm-pivot yoke 2. Carrier-frame shaft 9. Use the following procedure on the rear cutting units when the height of cut is above 19 mm (3/4 inch). A. Remove the lynch pin and washer securing the lift-arm-pivot shaft to the lift arm and slide th ...

Procedure The turf compensation spring (Figure 14) transfers weight from the front to the rear roller, helping to reduce a wave pattern in the turf, also known as marcelling or bobbing. Important: Make spring adjustments with the cutting unit mounted to the traction unit, pointing straight ahead, and lowered to the shop floor. 1. Ensure that the hairp ...

Parts needed for this procedure: Varies Rear weights (size varies with configuration). Procedure The machine complies with EN ISO 5395:2013 and ANSI B71.4-2012 standards when equipped with rear weights and/or 41 kg (90 lb) of calcium chloride ballast in the rear wheels. Use the following charts to determine the combinations of weights required for your configuration. Order parts from your Authorized Toro Distributor. Weight P/N 11 ...

• Mount the weight(s) and the traction manifold to the bumper with the 3 bolts, washers, and spacers previously removed (Figure 15B). Note: Do not use the spacers when installing more than 2 weights under the bumper (Figure 15C). • Secure the outer edges of the weight(s) to the bumper with 2 carriage bolts and nuts (Figure 15C). 6 Installing the CE Hood Latch Par ...

pin (Figure 19). Figure 19 1. Chain bracket 3. Cutting-unit kickstand 2. Snapper pin Product Overview Controls Seat-Adjusting Controls The seat-adjusting lever (Figure 20) allows you to adjust the seat fore and aft. The weight-adjusting knob adjusts the seat for the operator's weight. The weight gauge indicates when the seat is adjusted to the weight of the opera ...

latch retracts. Figure 21 1. Traction pedal 4. Brake pedal 2. Mow-speed limiter 5. Parking brake 3. Spacers 6. Tilt-steering pedal Tilt Steering Pedal To tilt the steering wheel, press the foot pedal (Figure 21) down and pull or push the steering tower to the most comfortable position and then release the pedal. Throttle Control Move the throttle control (Figure 22) forward to increase the engine ...