Keithley 300 Instruction Manual
Text of the manual
MODEL 300 OPERATIONAL AMPLIFIER
TABLE OF CONTENTS
Section
Page
1.
GENERAL DESCRIPTION . . . . . . . .
1
l-l.
General
. . . . . . . . . . .
1
l-2.
Features
. , . . . . . . . .
1
l-3.
Specifications
. , . . + . .
2
l-4.
Operating
Modes : , . . , . .
3
1-5.
Accessories
. . . . . . I . .
3
l-6.
Equipment
Shipped
. . . ,. . .
3
2.
OPERATION . . . . . . . . . . .
MODEL 300 OPERATIONAL AMPLIFIER
SECTION
1.
GENERAL
DESCRIPTION
GENERAL DESCRIPTION
l-l.
GENERAL.
a.
The Keithley
Model
300 Electrometer
Operational
Amplifier
is a compact,
ed amplifier.
It
has greater
than
1014 ohm input
resistance
and less
than
5 x
sing&-end-
lo-
ampere current
offset.
Its
current
drift
is
less
than
lo-l5
ampere/24
hours
and its
cur-
rent
n
MODEL 300 OPERATIONAL AMPLIFIER
l-3.
SPECIFICATIONS
(Measured
at 250C).
DC VOLTAGE GAIN,, OPEN LOOP:
Unloaded:
Greater
than
20,000.
lOOO-ohm load:
Greater
than
12,000.
INPUT CHARACTERISTICS:
Resistance:
Greater
than
1014 ohms.
Capacitance:
Less than
10 picofarads.
Current
Offset:
Less than
5 x LO-l4
ampere.
Drift:
Less than
lo-l5
ampere/2
MODEL 300 OPERATIONAL AMPLIFIER
GENERAL DESCRIPTION
l-4.
OPERATING MODES.
The Model
300 is
primarily
a current
amplifier.
It
can be con-
veniently
used in a number of operating
modes:
linear
current
amplifier,
logarithmic
current
amplifier,
current
integrator
and charge
amplifier.
Section
2 describes
these
and
other
operating
modes for
the Model
300.
1-5.
AC
MODEL 300 OPERATIONAL AMPLIFIER
Pin No.
Designation
Description
Paragraph
Reference
INPUT
INPUT
Teflon
Insulated
Coaxial
Input
2-4
1
ALT. INPUT
May be used for
large
signals
2-4
2
GUARO
Used with
ALT. INPUT
2-4
3
B
For remote
mounting
zero
control
2-14
4
A
For remdte
mounting
zero
control
2-14
5
-REF
Negative
Reference
Voltage
(-14
volt
output)
2-1
MODEL 300 OPERATIONAL AMPLIFIER
OPERATION
SECTION 2.
OPERATION
2-l.
TERMINALS.
The Model
300 input
connector
is a Teflon-insulated
coaxial
receptacle.
The 15-terminal
card-edge
is
used for
all
other
connections.
The mating
connector
for
the
15-terminal
card-edge
is keyed
to prevent
improper
insertion.
Refer
to Figure
2 and
Table
1 for
terminal
identification
MODEL 300 OPERATIONAL AMPLIFIER
5.
Fasten
the connectors
in
their
proper
positions.
6.
Attach
the Model
300 to its
mating
connectors.
d.
The terminals
of the mating
connectors
correspond
exactly
to,the
terminals
of the
Model
300 shown in Figure
2.
CS-179 is
the mating
connector
for
the
INPUT Receptacle,
and CS-175-15
is
the mating
connector
for
the