Onicon D-100 Installation Manual

BACnet Network Interface Installation Guide 11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 www.onicon.com • [email protected] 03-18 0635-11 / 18341 BACnet ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 2 ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 3 TABLE OF CONTENTS 1.0 INTRODUCTION ..................................................................................................5 1.1 PURPOSE OF THIS GUIDE .......................................................................5 1.2 TYPICAL ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 4 ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 5 D-100 SCROLL RESET PROGRAM ONICON 3864 Steam Building Domestic Water Supply Flow rate and total data to Data Acquisition System or Building Control System 120VAC or 24VAC Input Voltage 1.3 SPECIFICATIONS BACnet NETWORK INTERFACE MS/TP RS485 ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 6 1.4 NETWORK SIGNAL CONNECTIONS 1.4.1 BACnet MS/TP BACnet MS/TP, 2-wire (half-duplex) serial output connections are connected to terminal T1 as shown. Do not exceed 4.4 in-lb (0.5 Nm) of torque when tightening. Terminal T1 Do not connect shields ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 7 1.4.2 BACnet/IP BACnet/IP, Base 10T output connections are made as shown. Requires Base 10T cable and RJ45 connector. ! CAUTION Only qualified service personnel should make connections between the D-100 Flow Display and the user’s external equ ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 8 1.4.3 Optional Network Interface With Isolated Digital Pulse Input (Di3) The D-100-BACnet Display can be provided with an digital input pulse for totalizing pulse outputs from external devices such as water or gas meters. Pulses are accumulated ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 9 Powered Pulse: This type of output refers to a pulse which has an associated voltage with it (see Fig. 2). Set the selector switch, S1 to Pwrd Pulse. The allowable voltage range is 5-24 VDC. The input impedance is set at the factory to be 11 KOH ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 10 Open Collector Sinking or Dry Contact: This type of output refers to an open collector switch configured in a current sinking arrangement or a dry contact switch (see Fig. 4 and 5). Set the selector switch, S1 to Sink. In either case, the switc ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 11 1.5 BACnet MS/TP BAUD RATE, BIASING & TERMINATION 1.5.1 Baud Rate Every ONICON D-100 is individually programmed at the factory with application specific data provided by the customer during the process of ordering the display, and this normally ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 12 1.5.2 Biasing and Termination The ONICON D-100 does not provide biasing voltage to the RS485 network. A jumper selectable 120W termination resistor is provided as show below. The termination resistor should only be used when the display is inst ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 13 STEP ACTION REACTION COMMENT 0 Obtain MAC address & device instance number from the network administrator. None. The MAC address is a three digit number from 001 – 254. The device instance number can be anything from 0 – 4,194,303. 1 With t ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 14 1.6.2 Changing the IP Address Changing the IP address requires the use of RUInet utility software and a PC with an Ethernet card and an available port. Assuming the display is programmed with the default address (192.168.1.24) the host PC must ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 15 5. From the Edit IP Address Settings menu (shown below) select option 1. Please note that the default subnet mask is 255.255.255.0 and should not be changed unless necessary. 6. Enter the new IP address as shown below and press enter. ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 16 7. The following message will appear. 8. When the address change is complete, the following message will appear. You must cycle power to the D-100 for the change to take effect. ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 17 1.6.3 Changing the Gateway Address Changing the gateway address requires the use of RUInet utility software and a PC with an Ethernet card and an available port. Assuming the display is programmed with the default address (192.168.1.24) the hos ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 18 5. From the Edit IP Address Settings menu (shown below) select option 3. 6. Enter the new gateway address as shown below and press enter. ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 19 7. The following message will appear. 8. When the address change is complete, the following message will appear. You must cycle power to the D-100 for the change to take effect. ...

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 20 SECTION 2.0: BACnet PICS AND OBJECTS • 0636 D-100 Network Interface Module BACnet/IP Driver Protocol Implementation Conformance Statement (PICS) BACnet Protocol Date: January 1, 2010 Vendor Name: ONICON Incorporated Product Name: D-100-BAC Ne ...