Zero Z01.03 Operation & User’s Manual

PG1 USER MANUAL AND CONFIGURATION Z01.REV01.2018 IT | EN | FR zero HOME AUTOMATION Z01.03 - SLIDING GATE MOTOR SUPPLY 230V ...

PG3 INDEX 01. SAFETY INSTRUCTIONS 02. OPERATOR TECHNICAL SPECIFICATIONS DIMENSIONS 03. INSTALLATION INSTALLATION DIMENSIONS INSTALLATION STEPS TIPICAL INSTALLATION 04. MAINTENANCE MANUEL RELEASE TORQUE TRANSMISSION 05. TROUBLESHOOTING 01. SAFETY INSTRUCTIONS ATTENTION: •To ensure the safety of people, it is important that you read all the following instructions. Incorrect installation or incorrect use of the product can cause physical injury and material damage. •Keep these instructions in a safe place for future reference. •This product was designed and produced strictly for the use indicated in this manua ...

PG4 02. OPERATOR TECHNICAL SPECIFIATIONS Z01 specifications are as follow: DIMENSIONS The dimensions of automatism Z01.03 are the following: Z01.03 Power Supply 230Vac 50/60Hz Operating temperatures -25°C to 65°C Power 650W Thermal protection 130°C Current 2,4 A Protection class IP44 RPM 1400 Working frequence intensive Capacitor 25µF Opening time 10 m/s Maximum gate weight 2000 kg Oil type Total Equivis HZS 68 Force 2500 N Clutch Double disc oil Noise level LpA <= 50 dB (A) Opening time 9.6 m/s Z01.03 W (mm) 210 L (mm) 290 H (mm) 335 L W H ...

PG5 03. INSTALLATION INSTALLATION DIMENSIONS During installation you will need to open the motor cover, to access various components on the inside. For this, loosen the screw until the cover is free to be removed. For correct operation of the automatism, it is necessary to pay attention to the dimensions given in the following images. On the Illustrated pictures below are the dimensions for the installation of the automated sy- stem. INSTALLATION STEPS QP 60 01. Position the operator 50 mm from the edge of the gate and perfectly square at an angle of 90° and mark the place to make the holes for the bushings. Mus ...

PG6 It is very important that these dimensions are respected! Only this way can be assured the correct functioning and durability of the operators! During the course of the gate, all elements of the rack must mesh properly with the pinion! All rack supports must be weld at the gate. Do not use mass or other types of lubricant between rack and pinion! • FLASH LAMP • ANTENNA • CONTROL BOARD • MOTOR • PHOTOCELL • PHOTOCELL • KEY SELECTOR TIPICAL INSTALLATION It is important to use mechanical stoppers in the opening and closing position of the gate. If not respected, components of the automation may ...

PG7 MANUAL RELEASE To open manually the gate in case of electric power failure or in case of damage, follow the below steps: 01. Open the protection cover to acess the key hole for the release. Insert the key and turn it 90°. 02. Pull the lever towards the outside, and you can now open/close the gate manually. NOTE : So that the automation will operate normally, close the unlock and turn the key to the original position. Check that the distance between rack and motor remains unchanged and this engages the teeth of the pinion of the engine correctly (over time can happen some distortion). Lubricate all systems/a ...

PG8 Problem Procedure Behavior Procedure II Door doesn’t work Make sure you have 230V power supply connected to control board and if it is working properly. Still not working. Consult a qualified ZERO technician. Motor doesn’t move but makes noise Unlock motor and move the gate by hand to check for mechani cal problems on the movement Encountered problems? Consult an experienced gate expert. The gate moves easily? Consult a qualified ZERO technician. Motor opens but doesn’t close Unlock motor and move the gate by hand to closed position. Lock motor again and turn off power supply for 5 se- conds. Reconnect ...

PG9 Discovering the origin of the problem 1. Open control board and check if it has 230V power supply 2. Check input fuses 3. Disconnect the motor from control board and test them by connecting directly to power supply in order to find out if they have problems. 4. If the motor works, the problem is on the control board. Pull it out and send it to our ZERO technical services for diagnosis. 5. If the motor doesn’t work, remove them from installation site and send to our ZERO technical services for diagnosis. Check all motion axis and associated motion systems related with the motor and the gate to find o ...

PG10 NOTE: _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _________________________________________________ ...

PG12 zero HOME AUTOMATION ZERO SRLS Via ROMA 25/A ALTAVILLA VIC. ITALIA [email protected] - www.miozero.it ...