ScrapBox WORKBOX 3.0 Side Table Installation Instructions Manual
Text of ScrapBox WORKBOX 3.0 Side Table Installation Instructions Manual
Side Table Installation Instructions Made in the U.S.A.
UPDATED: JUNE 2019
oh happy day
YOU’VE RECEIVED YOUR SIDE TABLE(S)!
You are minutes away from even more room to create! Installation will be simple
and fun. If you need any assistance, our customer service team is the friendliest
bunch and would be delighted to help you!
[email protected]
www.theoriginalscrapbox.com
801-226-2686 M-F 9am-5pm MST
Remember to take pictures of your
more space for everyone
04
Installing your Side Tables in the WorkBox 3.0
13
Installing your Side Tables in the DreamBox
22
Using the Shelf Peg Tool
Proprietary, patented product and instructions. Do not copy or distribute.
WORKBOX 3.0 Side Table Installation
** You may have noticed that your Hard-
ware Bag includes some extra hardware.
This is all the additional hardware you would
need to install your tables in a DreamBox, just
in case you ever decide to upgrade. You can
set it aside for now.
TOOLS YOU’LL NEED (NOT INCLUDED):
Manual phillips
screwdriver
Permanent
marker
A friend to help you
HARDW
Proprietary, patented product and instructions. Do not copy or distribute. Count up 17 shelf peg holes from the bottom and remove all 13 x 13
shelves and shelf pegs from peg hole #17-18 in the left/right box. Also
remove notions-sized shelves and shelf pegs that share peg hole #18
in the narrow section(s) of the left/right box.
*You may have to rearrange some shelves/totes to make space for the
side tables. You may need to remove one or two totes enti
Proprietary, patented product and instructions. Do not copy or distribute. Hold one track up to the side panel on your left/right box to determine which column of
screw holes aligns with the hold pattern on your box. Correct column will vary between
boxes. Mark the correct column on both tracks with a permanent marker.
2
outer or inner column
outer or inner column
Lay both tracks on a hard, flat surface and use a manual
Phillips screwdriver to“start�
Proprietary, patented product and instructions. Do not copy or distribute. With screw side down, position the table tracks
over shelf peg hole #18 on both sides of left and/or
right box. Use a manual screwdriver to secure
tracks.
4
16
20
21
22
19
Proprietary, patented product and instructions. Do not copy or distribute. Install (1) Sash Lock (hook side only) to the underside of the
Side Table using the pre-drilled pilot holes closest to the
cutaway end.
Left Side Table
Underside
Left Side Table
Underside
6
5
Cutaway end
Barrel Lock Catch
Pilot Holes
x4
14mm
Washer Screws
(for table legs)
Install (1) Side Table Leg to Side Table using (4) table leg screws into the pre-drilled
holes. If your tabl
Proprietary, patented product and instructions. Do not copy or distribute. Apply Left and/or Right Side Guide Sticker to
UNDERSIDE of the WorkBox table in the left/right
corner. Be sure sticker is up against the front and
outside edges of the table.
7
FRONT
OUTSIDE EDGE
underside of
WorkBox Table
FRONT
OUTSIDE EDGE
underside of
WorkBox Table
side edge of WorkBox table
(near the outer end)
Use the provided screws to
attach (1) Sash Lock Catch
(per side
Proprietary, patented product and instructions. Do not copy or distribute. With Side Table Leg folded out, turn the table over.
Slide left/right side table(s) into tracks until table touches the back panel of the left/right box.
With Center Box table folded out, adjust the legs so your Side Tables are even with the
Center Table. Lock the sash lock on each side to secure tables together.
Most floors are not perfectly level. Use the threaded feet on the