CATSKILL 15218 Assembly Instructions Manual

Text of CATSKILL 15218 Assembly Instructions Manual

Deep Drawer Island

GENERAL: 1. You have purchased model 15218. 2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at 607-652-7321 from 7:30 am - 4:30 pm Eastern and we’ll send you the prepaid part via UPS usually that same day! You may also email us: [email protected]. 3. Read the assembly instructions and the enclosed brochure before beginning assembly. Assembly

Parts List Model 15218

Left Side Panel (1) P/N LFT/SP/HDL-15218/63037 Back Panel (1) P/N BP-15218 Glide Support (2) P/N GLDSUP-15218 Top Drawer Front (1) P/N DF-15218 Top Left Drawer Side (1) P/N Top DS-15218/L Top Right Drawer Side (1) P/N Top DS-15218/R Bottom Shelf (1) P/N BS-15218 Top & Bottom Front Braces (2) P/N B34 1/4 / 2 1/2 /BOT-15218 Table Top (1) P/N TT-15218 Drop Leaf (1) P/N DL-15218 Top Drawer Back (1) P/N DBK-15218 Top Drawer Bottom (1) P/N

1 3/4” Phillips Flat Head Bolt (8)

1 1/4” Phillips Flat Head #8 Screw (20) 1” Truss Head Machine Screw (6) 5/8” Phillips Flat Head #8 Screw (20) 3/4” Long 3/16” DIA. Steel Pin (8) 1” Long 3/16” DIA. Steel Pin (8) 1 1/2” Long 3/16” DIA. Steel Pin (2) Hinge (2) Caster Socket (4) 5/8 Wooden Disk (8) Nickel Handle (5) Towel Bar Post (4) Wheel Casters (2) Locking Wheel Casters (2) Magnet Plate (1) Magnet (1) 3/16” Flat Washer (13) 10-24 He

STEP 1A -

Important - Please Read These Instructions Carefully! Push this lever down, then slide the inner glide section out of the glide assembly. FRONT OF CART Face of Glide Backside of Glide Use these three (3) holes to attach the glide to the side panel. This edge will attach to back panel in the next step. TOP Front Attach Glides to Side Panels 1. Remove the drawer side section of the glide by pushing the black lever down and sliding the steel inner g

IMPORTANT - There is a right and a left side panel. Lay them out as shown below. Pay close

attention to the glides so that they are properly positioned when attaching to the side panels. Review Step 1A for specific instructions on the full extention glides. Attach L Brackets with 5/8” #6 screws. Use the small round hole, not the slot. PLEASE NOTE - Some pieces are interchangeable with other units we manufacture, and thus some pilot holes may not

1. The Bastion fastening system consists of a steel post (threaded on one end with a

hole through the shaft on the other end); a Barrel Nut (cylindrical barrel-shaped with threaded open end & holes through the sides); and a Set Screw (Phillips slot on one end, pointed on the other) 2. To attach Posts: A) Dip threads of Post in vegetable oil. B) Align threaded end of Post with hole in wood, tap on slotted end with hard hammer until threads enter, the

A. Attach the Top Drawer Back to the Drawer Sides with four 1 1/4” #8 screws. There are left and right

sides. Make sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to accept the Drawer Bottom. B. Slide in Drawer Bottom, best side up, to inside of drawer. C. Take the 2 bastion posts, align the threaded end of the posts with the post holes located near the ends of the inside of the Drawer Front. Tighten po

Perform a similar drawer assembly as Step 2 for the lower drawers.

A. Using 1-1/4” #8 screws, attach the drawer back to the drawer sides as shown below. B. Slide the drawer bottom into the slots. C. Insert Bastion Posts into the drawer front and tighten into position. D. Insert Barrel Nuts into the holes on the drawer sides, and slide the drawer front into place. Tighten with the set screws. Use hand screwdriver or hex wrench. E. Attach the full e

A. Tap/insert ONE 1 1/2” pin into each end of the door. DON’T OVERDRIVE PINS! Pins should stick

up about 1/2” when seated. Ok if loose. B. Attach the magnet plate (may be stuck to magnet in the hardware pack!) with a 1/2” #4 screw to the top of the door. Bumps go toward the wood, and the plate should be vertical. C. Attach door handle with 1” truss head machine screws. Use washers if necessary to tighten. 1” Truss Head Machine Screw 2 Us

CATSKILL Indoor Furnishing Owners Instructions: