FIORENTINI I26PF Manual 

pag. 3 INTRODUCTION 3 TECHNICAL DESCRIPTION 4 GENERAL INFORMATION 5 MANUFACTURER RESPONSABILITY 5 INTERVENT REQUEST 5 TRANSPORTATION 6 UNPACKING THE MACHINE 6 HANDLING OF PACKED MACHINE 6 HANDLING OF UNPACKED MACHINE 6 OPERATORING CONTROLS 7 DASHBOARD CONTROLS 7 ALARM REPORTING 7 DASHBOARD SYMBOLS 8 USE OF THE MACHINE 9 SAFETY SYSTEM 9 BRAKE 10 INSTALLING THE BATTERY CHARGER 10 CHOOSING THE DETERGENT SOLUT ...

DUE TO TRANSPORT AND CHECK TO HAVE RECEIVED ALL THE SHOWING ON THE DOCUMENTS. IN CASE OF DAMAGES OR MISSING PART PLEASE ADVISE IMMEDIATELY THE MANUFACTURER INTRODUCTION THIS KIND OF SCRUBBER MACHINE ALLOWS THE OPERATOR TO CLEAN ALL KIND OF FLOOR AND ALL KIND OF DIRTY ,GIVING THE BEST RESULT. YOU CAN REACH BEST PERFORMANCES USING THE M ...

650 mm 810 mm HEIGHT 1010 mm 1010 mm N° BRUSHES 2 2 BRUSHES SIZE ∅280 mm ∅330 mm WORK WIDTH 525 mm 650 mm SQUEEGEE WIDTH 750 mm 840 mm SOLUTION TANK IN POLYETHYLENE 100 liters 100 liters RECOVERY TANK IN POLYETHYLENE 85 liters 85 liters FRONT WHEEL DIAMETER 200 mm 200 mm REAR WHEEL ...

accidents, etc.due to the non-acquaintance (or non-fulfilment) of the prescriptions contained in this manual .The same applies to change’s execution, modifications, and/or to the installation of accessory not preliminarily authorized. In particular the firm ING FIORENTINI SRL is not responsible for any damages caused ...

The machine is supplied packed on pallet, closet in a box made of plywood or paper board. The weight and sizes are showed in the normal characteristics. The barycentre position is indicated by black arrow on the box. The forks of the lift truck or the transpallet should be placed so that the black arrow indicated on the packing is about in the centre of the forks. The package should be handled with extreme cauti ...

start (key inserted) one of the direction microswitch is already closed. 2 FLASHES Battery is undervoltage or discharged. This alerts that the voltage isn’t enough for a correct operation of the vehicle. 3 FLASHES Diagnostic code not used 4 FLASHES Electric motor circuit is sensed to be opened. 5 FLASHES Speed controlle ...

Squeegee Lowering Brush lifting Squeegee Lifting Brush lowering Reverse Increase by Traslation Forward General stop ...

SAFETY SYSTEM The machine is equipped with double safety system for emergency stop: • Mushroom push button . In emergency case press down this button. • Socket (fig. 3), the same is also used to charge the battery. In emergency case, the socket must be pull out from the plug using its handle (fig 4). Before learning how to use the machine, the operator should be familiar with the use of this safety system, to automatically use it ...

To avoid operator crushing when machine run in reverse speed, there is a safety (fig.5), that is a great surface lever. When it touch the operator it disconnect immediately the reverse speed and insert forward speed. In this way we reduce at the minimum the shock or the operator crushing, caused by a wrong manoeuvre. Fig. 5 BRAKE The machine is provided with a parking and an emergency brake as well.(fig.7). • The emergency brake i ...

• Install the battery charger in a ventilated and dry place, far from heat sources and corrosive environments. • Protect the mains with a delayed switch or with a load fuse higher than the max. power consumption of the battery charger. • Observe the polarity of the battery socket (black cables are identified by symbols + and -). CHOOSING THE DETERGENT SOLUTION For a good cleaning of the floor, it is important to choo ...

The main caracteristic of this type of squeegee is to pick-up the water from the floor and convey to the vacuum hose, but it must be paralle to the floor.To rightly adjust the squeegee operate as follow: • Extract the key from the control dashboard to avoid accidental start of the machine. • To ...

accidental ignition of some motors could cause damages • First of all remove the knobs (fig.) by unscrewing them, then extract the brush covering carter • Rotate each brush until its knob (fig.) can be reached, then extract it and remove the brush fallen on the ground. • To insert the new brush, place the hexagon of the female joint ...

GENERAL SAFETY RULES Before using the machine ,instruct all operators to read carefully the charter ”SAFETY STANDARDS “WARNING. • The manufacturer can make any changes to the machine, for constructive or commercial reasons, without being obliged to change the instruction manual at the right time according to these modifications. • The person responsible for the machine must adhere to CEE rules and to the local ...

when going through a downhill road, always adjust the speed to the environment conditions. Do not turn the machine at excessive speeds, particularly if the floor is not flat. CAUTION: DANGER Never operate the machine when stopped for special operations (setting up, maintenance, etc.). Before starting the work, check for any possible visible defects on the saf ...

All six month, check the efficiency of the safety devices, the inspection should be performed by qualified personnel of FIORENTINI s.r.l. or authorized by it. To grant the efficiency of the safety devices, the machine should be overhauled by a technician of FIORENTINI every 5 months. ANNUAL CHECK The responsible person should perform an annual check to determine if the machine complies with the technical safety standards. After thi ...

DAILY • Clean the recovery tank and the filter of the vacuum motors. WEEKLY • Check for the cleaning of the suction pipes and of the squeegee • Check the state of the rubber squeegee blades • Check battery water level MONTHLY • Check the filter of the clean water tank ALL SIX MONTHS • Check batery connections EACH YEAR • Check the brush state of each motor AFTER TWO YEA ...

edge is essential for a perfect drying. To replace the blades • The squeegee should be demounted from the machine and placed on the desk. • Now, remove the screws (fig) both on the front part and on the rear part of the squeegee, the steel straps and remove worn rubber blades • Perform the inverse procedure and assemble the new blades, then adjust th ...

and replaced, if necessary. After removing the key from the dashboard, descrew the screw in the vacuum motor space, open it, unhook the hooks and detach the plug . In this way, it is possible to extract the motors and release the sponge filter under the motors that can be extracted, cleaned and replaced. Check the suction fan from the hole located in the front pa ...