Vingtor ACM-M-A-V2 Operation & User’s Manual

P.O. Box 4498 Nydalen NO-0403 OSLO Norway STENTOFON and VINGTOR products are developed and marketed by Zenitel Norway AS. The company’s Quality Assurance System is certifi ed to meet the requirements in NS-EN ISO 9001:2002. Zenitel Norway AS reserves the right to modify designs and alter specifi cations without prior notice, in pursuance of a policy of continuous improvement. © 2009 Zenitel Norway AS. DOC NO A100K10587 v.1.0 [email protected] Phone list In use indication Microphone mute Pause (Not used) Redial R (or Flash) Dial keys Loudspeaking Ringing signal Hi/Lo volume Flash/R switch. Select R mode Handset Hi/Lo volume Telephone line, RJ11 Ext. Phone, RJ11 VINGTOR analogue telephone DT-800M USER GUIDE ACM Telephone System ACM-M-A-V2 2009.05.27 A100K 10587 v.1.0

Some analogue telephones have special feature keys which are needed for some of the described functions. Establish internal telephone call Lift handset ● Dial number of desired phone ● Call is set up when remote phone handset is lifted – Replace handset to end the conversation ● Establish external telephone call Lift handset ● Dial trunk access code (default = 001) to get external dial tone ● Optional: Enter user and PIN code for call authorization for call – billing. See programming list for actual code. Dial external phone number ● Call is set up when handset on remote phone is lifted – Replace handset to end the conversation ● Receive call in noisy area For calls in noisy areas, the telephone line will be connected in parallel to a signal unit. Signal unit will provide visual or audio indication on incoming – call Lift handset to receive call ● Public address (PA) call Lift handset ● Dial 84 for general PA call without zones ● Call is set up towards the PA system – System plays a DING-DONG to the PA system – After DING-DONG, speak into handset for PA announcement ● Replace handset to end the PA call ● Microphone mute Only for telephones with MUTE button. Press and hold the MUTE button to block own microphone during ● conversation Release the MUTE button to re-open the microphone ● Re-dial Only for telephones with REDIAL button. Replace handset or push the handset switch ● Lift handset ● Press the REDIAL button to repeat last dialed number ● Redial can not be used for external calls + X MUTE REDIAL + PBX Functions Inquiry call Only for telephones with R button. Press R+2 during conversation ● Dial number of desired phone ● Call is set up when handset on remote enquired phone is lifted – Press R+2 to toggle between the phones ● The other conversation will be parked – Replace handset to disconnect both phones ● Call transfer Only for telephones with R button. Press R+2 during conversation ● Dial number of desired phone ● Call is set up when handset on remote enquired phone is lifted – Press R+3 to transfer the call ● Replace handset to withdraw from conversation ● The two other phones will remain in conversation – Call forwarding Lift handset and dial 71 ● Dial remote phone number you want calls forwarded to ● Press the ● ¾ button to confi rm Replace handset ● Own phone will ring for ca. 10 sec. when called, – then forwarded if not answered Dial 70 from your own phone to cancel Call forwarding ● Follow me Lift handset on the phone you want calls to be transferred to ● Dial 72 ● Dial your own phone number ● Replace handset ● Own phone will ring for ca. 10 sec. when called, – then transferred to present phone if not answered Dial 73 + own phone number to cancel Follow me ● Busy notify If the called station is busy, dial 57 or press the ● ¾ button to send an attention tone (3 beeps) to the busy stations. Call priority and busy override Only a selected set of telephones will have option for busy override. If caller get busy tone, dial 58 or ● ¾¾ for busy override The other call is disconnected and the priority call is set up – R R R + + + + CALLER OWN REMOTE R R + + + CALLER OWN REMOTE + + CALLER OWN REMOTE C= + + CALLER OWN PRESENT C= OR OR