Progress Lighting AirPro P2562 Installation Manual

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of any sea coast. Extended warranties for ENE ...

Safety Rules..................................................................................................................................................................................... Unpacking Your Fan ....................................................................................................................................................................... Installing Your Fan .......................................................................................................................................................................... Operating Your Fan ................................................... ...

1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device. 4. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.) Or Less" and use mounting screws provided with t ...

Unpacking Your Fan 2. 10. Loose parts bag containing: a. Blade attachment hardware (16 screws, 16 rubber washers ) b. Mounting hardware Wire nuts (3) c. Electrical hardware Pull chain 1. Fan blades (5) 2. Canopy assembly 3. Down rubber cover 4. Ball/downrod assembly 5. Coupling cover 6. Set of blades bracket (5) 7. Fan motor assembly 8. Mounting plate 9. Switch housing 10. Balancing kit 10 a c b 1 2 6 9 10 7 8 4 3 5 ...

adjustable wrench, step ladder, and wire cutters. Mounting Options If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Useappropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes. Figure 4 Figure 3 Figure 1 Figure 2 Outlet box Outlet box Outlet box Note: You may need a longer downrod to maintain ...

REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise.(Fig. 5) Step 2. Remove the mounting bracket from the canopy by removing the 1 of 2 screws from the bottom of the mounting bracket and loosening the other one a half turn from the screw head. Next, turn the canopy counter clockwise to removing the mounting bracket from the canopy. (Fig. 5) Step 3. Pass the 120-volt supply wires through the center hole in the ceiling hanger bracket as shown in Fig. 6. Step 4. Secure the hanger bracket to the ceiling o ...

WARNING ELECTRICAL DIAGRAMS ARE FOR REFERENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE UL LISTED AND MARKED SUITABLE FOR USE WITH THIS FAN. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. Make the Electric Connections REMEMBER to disconnect the power. If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps ...

Step 1. Tuck connections neatly into ceiling outlet box. Step 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 9) Step 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws. Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug. WARNING MAKE SURE THE NOTCH ON THE HANGING BRACKET PROPERLY SITS IN THE GROOVE IN ...

Plate Step 1. Remove 1 of the 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) Step 2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig. 13) Blade Balancing 1. Check that all blade and blade arm screws are secure. 2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on ...

Housing Step 1. Remove the 1 of 3 screws from the mounting plate and keep it for future use. Loosen the other 2 screws. (Do not remove) Step 2. Snap the wire connection plugs together. Step 3. Place the key holes on the switch housing over the 2 screws previously loosened from the mounting plate, turn switch housing until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Figure 14) Connection plugs 8. ...

Turn on the power and check the operation of the fan. The pull chain controls the fan speed as follows: 1 pull - High 2 pulls - Medium 3 pulls - Low 4 pulls - Off. Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, and so on. The slide switch controls directions: forward (switch left) or reverse (switch right). Warm weather - (Forward) A downward air flow creates a cooling effect as shown in Figure 15. This allows you to set your air conditioner on a higher setting without affecting your comfort. Cool weather - (Reverse) An upward airflow moves warm air off the ceiling ...

fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing. Do not use water when cleaning. This could damage the motor, or the wood, or possibly cause an electrical shock. 3. You can apply a light c ...

2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing. CAUTION: Make sure main power is off. 4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time. 5. If using an optional light kit, make sure the screws securing the glassware are tig ...

701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved c Specifications 12. 26.40 lbs 30.14 lbs 2.60' Fan Size Speed Volts Amps Watts RPM CFM N.W. G.W. C.F. 60" Low High 120 120 These are approximate measures. They do not include Amps and Wattage used by the light kit. 0.263 0.59 13.9 70.4 55 133 2533.31 6472.21 ...

Lugar de compra N de modelo. N de serie Numero de vendedor UPC 109226 Garantía limitada de por vida Se garantiza al comprador original que los motores de los ventiladores de Progress Lighting no presentan defectos mecánicos o eléctricos por el tiempo durante el cual el comprador original sea dueño del ventilador. Los interruptores de cadena, interruptores de reversa, capacitores y acabados de metal cuentan con garantía libre de defectos de materiales o mano de obra por 1 año a partir de la fecha de compra. La deformación de las aspas de plástico o madera no está cubierta por esta garantía, así como tampoco la corrosión y/o e ...

Normas de seguridad ....................................................................................................................................................................... Cómo desembalar el ventilador ...................................................................................................................................................... Cómo instalar el ventilador ............................................................................................................................................................. Cómo operar el ventilador ......................................................... ...