ETS PinPulse Operating Manual

Text of ETS PinPulse Operating Manual

www.electrotechsystems.com (833) ESD-GURU (833-373-4878)

D00219 – Revision E – 20190722 ESD Testing System Model 9910 PinPulse™/PinScan™ Operating Manual

www.electrotechsystems.com 833-ESD-GURU (833-373-4878)

D00219 Revision E – 2019-07-19 - Page 2 Table of Contents I. IMPORTANT SAFETY INFORMATION .................................................................................................................... 3 II. DESCRIPTION OF CONTENTS ............................................................................................................................... 5 III. SETUP GUIDE ............
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 3 I. IMPORTANT SAFETY INFORMATION WARNING: Equipment contains High Voltage. The equipment described in this Manual is designed and manufactured to operate within defined design limits. Any misuse may result in electric shock, damage to equipment, or fire. To prevent these unwanted events, the following rules should be observed for installation, use and mai
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 4 DO NOT OPERATE WITH SUSPECTED EQUIPMENT FAILURES. If any odor or smoke becomes apparent turn off the equipment and unplug it immediately. Failure to do so may result in electrical shock, fire or permanent damage to the equipment. Contact the factory for further instructions. DO NOT OPERATE IN WET/DAMP CONDITIONS: If water or other liquid penetrates the equ
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 5 II. DESCRIPTION OF CONTENTS 1. The ETS PinScan consists of an automation system mated with the ETS 9910 PinPulse discharge simulator. A testing deck at the top mounts devices to be tested and an acrylic safety cover encloses the test area. 2. A laptop PC computer pre-loaded with windows-10 and the necessary PinScan Test Manager software loaded and opera
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 6 III. SETUP GUIDE STEP 1: Set up the system on a clean well-illuminated work area. STEP 2: Plug in the 2 USB cables. One cable is a USB Type A –to- RS232 (DB9) cable which connects the 9910 (lower) electronics to the computer. The other cable is a USB Type A –to- USB Type A cable which connects the PinScan transport (upper) electronics to the computer
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 7 STEP 5: Attach the discharge cables. Choose the pair of cables for the discharge model you are using: HBM, HMM, or MM. Attach the ground cable from the GND (silver) banana jack on the PinPulse tower to the right-hand clip-on ground terminal on the PinScan Deck. Plug the positive cable into the labeled color-coded banana jack on the PinPulse tower, (
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 8 STEP 9: Click on the PinScan Test Manager icon . The Operator Screen will open as shown with operating buttons across the top of the window. The yellow highlighted instruction fields are important – they display status updates and requests for operator action. (Program Control): The Test Manager will indicate the running condition by the appearance of
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 9 IV. QUICK START GUIDE After setting up the system as described above, PinScan is ready to operate. This section covers the steps necessary to create a quick no-frills test, without considering options or customization. The quick start process is as follows: START PROCEDURE: • After launching the PinScan Test Manager , the yellow banner will display
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 10 • The first time the system is run, a check of the COM ports is recommended. The PC is shipped with the COM ports properly configured, however this is not completely dependable in the windows environment. See Appendix B for COM Port Setup. • Click on the RUN TEST button to create a new test. PinScan will create a new number for your test, a 4-digit
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 11 4.3. CONFIRM THE VOLTAGE SCRIPT For each pin pair in the PinScript, a sequence of discharge pulses will be applied, at specific voltages listed in the Voltage Script. (A.K.A. “VScript”) The system will have a Voltage Script loaded and ready to run and its number will appear in the VScript Ref# field. (7001 as shown in the example above). Click on G
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 12 4.6. SELECT THE ESD MODEL Leave this model as-is: 4.7. SELECT THE CURVE TRACE OPTION Click on Option 2 – CT after each discharge: Accept these 3 options by clicking GO. 4.8 RUN THE TEST. The system is now ready to begin the test. Click GO *** TESTING BEGINS *** PinScan starts the following sequence of actions: • The PinScan transport will move
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 13 Live test status display: NOTE: The following Curve Trace and PinCheck displays only apply if Curve Tracing is active. • To the right of the Test Status area is the Curve Trace chart. If curve tracing is selected, a plot will appear here of current vs. voltage for the pin pair presently addressed. A typical diode characteristic is shown at the right.
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 14 • PinScan computes the variance of the PinCheck numbers for each pin, for an indication of how constant the traces are across all the discharges. Then the results are shown in the Variance Report. This is sorted by variance, so any problem pins as indicated by a high variance show up at the start of the list. This chart is updated live when the testi
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 15 Four yellow buttons will be activated: Next CT and Prev CT for individual navigation among the curve traces, and Next Pin and Prev Pin for navigation by device pin. • Click on “Next CT” to step to the next curve trace, • Click on “Prev CT” to step back to the previous curve trace. • Click on “Next Pin” to step ahead to the following pin,
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 16 V. OPERATION GUIDE 5.1. Organization of the System An organization block diagram of PinScan ESD testing is shown below. The first step is to formulate a Test Plan and the objectives of the test, and this will dictate the Voltage ranges and pin combinations to be examined. The system can address any pair of pins on the device, and can apply discharge wav
www.electrotechsystems.com 833-ESD-GURU (833-373-4878) D00219 Revision E – 2019-07-19 - Page 17 The Adapter board plugs into the PinScan Stage. This makes all of the Device pins accessible to PinScan for testing. The picture below shows an Adapter board mounted on the left half of the PinScan Stage. This is a 64 pin Adapter board and two simple 3-lead components are mounted on it. Adapter boards can be configured to handle a single large device or

ETS Test Equipment Owners Instructions: