Intel P67 Operation & User’s Manual

Based M/B for Intel LGA 1155 Processors Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. NO. G03-HI08-F Rev: 1.0 Release in: December, 2010 ...

Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle. ...

USER’S NOTICE .......................................................................................................................iv MANUAL REVISION INFORMATION.......................................................................................iv ITEN CHECK LIST ...................................................................................................................iv COOLING SOLUTIONS ............................................................................................................iv CHAPTER 1 INTRODUCTION OF ...

� Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. � 0 to 40 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) � Generally speaking, dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots’ that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB ...

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARES DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED FOR THE UTILIZATION OF THESE MOTHER-BOARDS TO MEET THE USER’S REQUIREMENTS. BUT IT WILL CHANGE, CORRECT AT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LO ...

1-1 Motherboard Specification Spec Description Design � ATX form factor; PCB size: 30.5x24.5cm Chipset � Intel P67 Express Chipset CPU Socket � Intel LGA 1155 socket Intel® Core™ i7 Processor, Intel® Core™ i5 Processor, Intel® Core™ i3 Processor * for detailed CPU support information please visit our website Memory Sockets � DDRIII module sockets x 4 � Support 4pcs DDRIII1066/ DDRIII 1333 MHz memory modules expandable to 16GB. � Support Dual- channel function Expansion Slots � 1 psc* PCI-Express2.0 x1 slot � 1 psc* PCI-Express 2.0 x16 slot by 16 lane � 1 psc* PCI- ...

CPU Smart Fan—The Noise Management System It’s never been a good idea to gain the performance of your system by sacrificing its acoustics. CPU Smart Fan Noise Management System is the answer to control the noise level needed for now-a-day’s high performance computing system. The system will automatically increase the fan speed when CPU operating loading is high, after the CPU is in normal operating condition, the system will low down the fan speed for the silent operating environment. The system can provide the much longer life cycle for both CPU and the system fans for game use and business requirements. CPU ...

CPU Socket ATX Power Conn. PCI Slot CPUFAN1 CDIN Header Power LED Header Speaker Header HDMI-SPDIF Header Front Panel Audio Header USB 2.0 Headers Front Panel Header 3D Audio Button Line-OUT Serial-ATA2 Connector ATX 12V Power Connector RJ-45 LAN Port Line-IN MIC-IN RS-OUT CS-OUT DDR3 Socket x 4 (DIMM1~DIMM4) SS-OUT USB 2.0 Ports Over PS/2 Keyboard Port Coaxial SPDIF_OUT PCI Express 2.0 x16 by 16 Lane Reset Button JBAT Gigabit LAN Chip 8-CH HD Audio Connector POWER＿CAP USB 2.0 Ports USB 3.0 Port PS/2 Keyboard Port Intel P67 Chipset 64MB Flash ROM 8-CH HD Audio Chip PCI Express2.0 x1 SYSFAN RJ-45 Over USB 2.0 Ports G.P.I. LED De ...

other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect hard disk and front panel /back panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10. Install Driver and Utility 2-2 Checking Motherboard� ...

KB/MS Power On Setting 2-3 Closed: KB/MS Power ON Enabled JP1 JP1 1-2 Closed: KB/MS Power ON Disable (Default) 2-3 Installing CPU 2-3-1 About Intel LGA 1155 CPU Socket This motherboard provides an 1155-pin DIP, LGA 1155 Land Grid Array socket, referred to as the LGA 1155 socket. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system. NOTED! Be sure that there is sufficient air circulation across the processor’s heat sink and CPU cooling FAN is working correctly, ...

1. Please make sure that CPU socket is facing towards you and the level is on you left hand side. 2. Press down the level and move it to the left side to make sure it is freed from the hook and then open it upwards about 135 degree. 3. Open the level upwards about 135 degree and the metal protection plate will be pulled up at the same time. 4. Remove the plastic protective cap from the socket. (Put it to the original place if CPU is not installed. Do not touch the metal contact point of the CPU socket). 5. Make sire that golden finger in the right place as shown in the above illustration and match the two al ...

above. 7. Press down the load level and move it rightwards make sure it is locked under the notch. 2-3-3 Intel Reference Thermal Solution Assembly 1. Put the heat sink vertically above the CP-installed socket and make sure to align the four fasteners with four holes around the socket. 2. Revolve the four fasteners in the counter-clockwise direction. 3. Press down two fasteners down in the oblique crossing direction as shown above. 4. Turn over the motherboard carefully to make sure the fastener insert in the right direction. Notice： Please apply thermal interface material to the CPU HIS surface. ...

for DDR III memory expansion available to maximum memory volume of 16GB DDRIII SDRAM. Valid Memory Configurations Bank 240-Pin DIMM PCS Maximum Capacity DIMM1 DDRIII 1066/ DDRIII 1333 X1 4GB DIMM2 DDRIII 1066/ DDRIII 1333 X1 4GB DIMM3 DDRIII 1066/ DDRIII 1333 X1 4GB DIMM4 DDRIII 1066/ DDRIII 1333 X1 4GB Total System Memory (Max.4GB) 4 16GB Recommend DIMM Module Combination： 1. One DDRIII Memory Module ----Plug in DIMMM1. 2. Two DDRIII Memory Modules---Plug in DIMM1 & DIMM 3 for Dual channel function 3. Four DDRIII Memory Modules---Plug i ...

2-5-1 Expansion Slot The P67 Express chipset based motherboard series offer one PCI-Express 2.0 x16 by 16 lane, one PCI-Express 2.0 x16 by 8 lane and one PCI-Express 2.0 x16 by 4 lane graphics slots. These two graphics slots support the latest AMD CrossFireX Technology and nVidia SLI to guarantee the fully operational Multi-GPUs graphics function and avoid the possible installation error. One PCI Express 2.0 x1 slot and two 32-bit PCI slots guarantee the rich connectivity for the I/O of peripherals. 2-5-2 Procedure for Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary ...

The following illustrations show you how to install the Bridge Card. In order to activate the CrossFire/SLI technology, you have to install the optional bridge card for your CrossFire /SLI Tech. Supported VGA Cards before you activating the advance multi-GPUs functions. Installation Reference 1. Install your VGA Cards in the PCI-E x16 slots. 2. Prepare with the Bridges with your VGA Cards. 3. Be careful with the position for the pin you would like to set up. 4. Keep straight to force the CF Bridges plug into both sides of CrossFire Tech Supported VGA Cards. After the above installation completed, pleas ...

2-6-1 I/O Back Panel Connectors (1) Coaxial SPDIF Out connectors: SPDIF_OUT1 This coaxial S/PDIF connector is provided to transmit digital audio signals to speaker by connecting a coaxial S/PDIF cable. (2) Optical SPDIF Out connectors: SPDIF_OUT2 This optical S/PDIF connector is provided to transmit digital audio signals to speaker by connecting an optical S/PDIF cable. (3) USB 3.0 Port s: USB 3.0_2.0 These blue connectors are 4-pin USB 3.0 connectors to connect USB devices to the system board. (4) USB 2.0 Port s: from USB3/USB20_KB_MS/USB20_LAN The connectors are 4-pin USB 2.0 connectors to connect USB devices to the syst ...

(1) Power Connector (24-pin block): ATXPWR1 ATX Power Supply connector: This is a new defined 24-pins connector that usually comes with ATX case. The ATX Power Supply allows using soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. Press this switch again will turn off the power to the system board. ** We recommend that you use an ATX 12V Specification 2.0-compliant power supply u ...

This is a new defined 8-pin connector that usually comes with ATX Power Supply. The ATX Power Supply which fully supports LGA 1155 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. Pin 1 (3) Serial-ATA3 Port connectors: SATA1, SATA2 These SATAIII connectors support SATA 6Gb/s specification. Please connect SATAIII device to the connector with SATA cable. One connector supports one SATA device. Pin No. Defnition 1 GND 2 TX ...

(1) Line-Out/MIC Header for Front Panel (9-pin): FP_AUDIO These headers connect to Front Panel Line-out, MIC connector with cable. Line-Out, MIC Headers AUDIO Pin 1 Lineout2-L Lineout2-R Sense-FB Audio-GND LINE2-JD Audio-JD 2 9 10 KEY MIC2-L MIC2-JD MIC2-R (2) CD Audio-In Headers (4-pin): CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. CD Audio-In Header Pin 1 L GND R (3) SPDIF Out header: HDMI_SPDIF1 This header provides S/PDIF digital signal transmission. Please connect it to certain expansion card (graphics card or sound card) with an S/PDIF digital ...

This header connects to the hard disk activity indicator light on the case. (7) Reset switch lead: RESET This 2-pin header connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. See the figure below. (8) Power switch: PWR BTN This 2-pin header connects to the case-mounted power switch to power ON/OFF the system. System Case Connections HDLED RESET VCC5 GND VCC5 PWR LED PWRBTN PWRBTN PWRLED HDDLE RSTSW NC GND JW FP Pin 1 SPEAK SPKR GND NC VCC5 Pin 1 PWRLED Pin 1 (9) USB 2.0 Port Headers (9-pin): USB1/USB2 These USB 2.0 headers are used for connecting the additio ...