curt 18112 Installation Manual

Text of curt 18112 Installation Manual

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 1

INSTALLATION MANUAL 18112 Tools Required Open wrench, 17mm Adjustable wrench Open wrench, 24mm Socket, 17mm Torque wrench Hex key, 6mm Level of Difficulty Easy Product Photo WARNING Do not carry flammable items on the carrier. Do not allow exhaust fumes to blow directly on items in the carrier. This is a fire hazard. Notes and Maintenance Before you begin installation, r

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 2

Parts List Qty Description # 1 Bottom bracket 1 4 U-clamp 2 9 Lock nut, M10 3 4 Eye bolt, M10 x 45mm 4 1 Carrier frame 5 1 Fixed plate 6 1 Button socket cap screw, M10 x 25mm 7 2 Eye bolt, M10 x 20mm 8 1 Flat washer, M10 9 1 Shank assembly 10 ASSEMBLY Parts List Qty Description # 1 Hex head bolt, M16 11 1 Lock nut, M16 12 1 Pin 13 2 Clip 14 1 Anti-rattle hitch pin, M16 15

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 3

Step 1 Align the holes in the upper ramp (#19) and lower ramp (#20) hinge brackets. Insert an M10 button socket cap screw (#18) into each hinge. Secure with an M10 lock nut (#3), ensuring the hinge operates freely.

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 4

Step 2 Place the bottom bracket (#1) on the bottom of the carrier frame (#5) and line up the square holes. Insert an M10 eye bolt (#4) through the bottom bracket, carrier frame and U-clamp (#2) in all four locations. Note: The head of the eye bolt will be on the outside of the carrier frame. Secure with M10 lock nuts (#3). Snug the hardware, but do not fully tighten.

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 5

Step 3 Mount the fixed plate (#6) to the carrier frame (#5) by inserting an M10 eye bolt (#8) through the upper hole in the fixed plate and the upper hole in the carrier frame as shown. Secure with an M10 lock nut (#3). Insert an M10 button socket cap screw (#7) through the lower hole in the carrier frame and the lower hole in the fixed plate. Secure with an M10 lock nut.

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 6

Step 4 Install the shank assembly (#10) on the bottom bracket (#1) by aligning the two upper holes in the shank assembly with both holes in the bottom bracket. Insert an M16 hex head bolt (#11) through the hole in the shank assembly and bottom bracket nearest to the cargo area. Secure with an M16 lock nut (#12), tightening until shank assembly still pivots freely. Insert

CURTMFG.COM • NEED ASSISTANCE? • 877.287.8634 • 18112-INS-RB • PAGE 7

Step 5 With the ramp in the upright position, fasten the rubber belt on the step bolt of the ramp. Note: To properly align the locking pin and the fixed plate, the upper ramp (19) and the rubber foot of the lower ramp (20) must be in contact with each other. Both sections of the ramp need to be moved together to allow the proper angle for the locking pin to align with the

curt Automobile Accessories Owners Instructions: