Det-Tronics X5200 Instructions Manual

Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 oi (Optical Integrity) . . . . . . . . . . . . . . . . . . . . . . 2 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Data Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Integral Wiring Compartment . . . . . . . . . . . . . . . . 3 SIGNAL PROCESSING OPTIONS . . . . . . . . . . . . . . 3 IR Detector Options . . . . . . . . . . . . . . . . . . . . . . . 3 UV Detector Options . . . . . . . . . . . . ...

with Pulse Output X5200, X5200G, X5200M IMPORTANT Be sure to read and understand the entire instruction manual before installing or operating the flame detection system. Any deviation from the recommendations in this manual may impair system performance and compromise safety. ATTENTION The X5200 includes the Automatic oi ® (Optical Integrity) feature — a calibrated performance test that is automatically performed once per minute to verify complete detector operation capabilities. Testing with an external test lamp is not approved or required. DESCRIPTION The X5200, X5200G, X5200M meet the most stringent ...

relays are rated 5 amperes at 30 Vdc. The Fire Alarm relay has redundant terminals and normally open / normally closed contacts, normally de-energized operation, and latching or non-latching operation. The Fault relay has redundant terminals and normally open contacts, normally energized operation, and latching or non-latching operation. Latching relays can be reset by removing input power (0.1 second minimum). An alarm condition will normally override a fault condition, unless the nature of the fault condition impairs the ability of the detector to generate or maint ...

the location marked “MAG OI” on the outside of the detector (see Figure 2). This action causes the detector to immediately send pulses to the controller. Controller response is as follows: • The Zone LED blinks. • The digital display indicates which zone is in alarm. • The status indicator shows “6” (fire). IMPORTANT Mag oi can be performed with the controller’s (R7404/R7494) keylock switch in either the NORMAL or TEST position. In NORMAL, the controller goes into alarm and activates its outputs. If no controller alarm output is desired, place the keylock switch in the ...

The Quick Fire (High Speed) feature can be used in conjunction with the TDSA signal processing method. This method overrides TDSA requirements in the event of an intense signal. When Quick Fire is activated, the detector is capable of responding to an intense fire signal in less than 30 milliseconds (0.030 seconds). Using the Quick Fire feature in conjunction with TDSA signal processing allows the detector to provide a high speed response to a large, non-flickering fire (such as in high pressure gas applications) while maintaining an ability to respond to smaller fires. UV DETECTOR OPTIONS The UV detector in the X ...

UV: The UV sensor is solar blind to the ultraviolet component of solar radiation. However, it will respond to sources of UV besides fire, such as electric arc welding, lightning, high voltage corona, x-rays, and gamma radiation. NOTE Radiation generated by false alarm sources such as periodic lightning or sparks in the area can be effectively ignored by the detector using the arc rejection feature or time delay. IR: The detector has been designed to ignore steady state infrared sources that do not have a flicker frequency characteristic of a fire, however, it should be noted that if these steady state infrared sources ...

WARNING Do not open the detector assembly in a hazardous area when power is applied. The detector contains limited serviceable components and should never be opened. Doing so could disturb critical optical alignment and calibration parameters, possibly causing serious damage. This type of damage could be undetected and could result in failure to see a fire and/or false alarm. CAUTION The wiring procedures in this manual are intended to ensure proper functioning of the device under normal conditions. However, because of the many variations in wiring codes and regulations, total compliance to these ordinances cannot b ...

O-rings is a silicone free grease (p/n 005003- 001) available from Det-Tronics. Under no circumstances should a lubricant containing silicone be used. DETECTOR POSITIONING Detectors should be positioned to provide the best unobstructed view of the area to be protected. The following factors should also be taken into consideration: • Identify all high risk fire ignition sources. • Be sure that enough detectors are used to adequately cover the hazardous area. • Be sure that the unit is easily accessible for cleaning and other periodic servicing. • Verify that all detectors ...

It is important to take proper precautions during installation to ensure that moisture will not come in contact with the electrical connections or components of the system. The integrity of the system regarding moisture protection must be maintained for proper operation and is the responsibility of the installer. If conduit is used, we recommend installing drains, according to local codes, at water collection points to automatically drain accumulated moisture. It is also recommended to install at least one breather, according to local codes, at upper locations to provide ventilation and allow water vapor ...

The ideal installation surface should be free of vibration and suitable to receive 3/8 inch or M10 bolts with a length of at least 1 inch (25 mm). The surface must also have sufficient capacity to hold the detector and mounting arm weights (see “Specifications” section). Refer to the Q9033 Mounting Arm manual, number 95-8686, for additional installation information. See Figure 3 for dimensions. Detector Wiring IMPORTANT If installing an X5200 in place of an existing detector, be sure to move the “A” Lead (detector power) at the controller from the +290 Vdc ...

B - INPUT 1 B - INPUT 2 B - INPUT 3 B - INPUT 4 B - INPUT 5 B - INPUT 6 B - INPUT 7 B - INPUT 8 D1-1 oi DRIVER D1-2 oi DRIVER D1-3 oi DRIVER D1-4 oi DRIVER D1-5 oi DRIVER D1-6 oi DRIVER D1-7 oi DRIVER D1-8 oi DRIVER D2-1 oi DRIVER D2-2 oi DRIVER D2-3 oi DRIVER D2-4 oi DRIVER D2-5 oi DRIVER D2-6 oi DRIVER D2-7 oi DRIVER D2-8 oi DRIVER DMA OUT AVAILABLE DMA OUT DMA IN DATA STROBE 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 ZONE OUTPUT 1 ZONE OUTPUT 2 ZONE OUTPUT 3 ZONE OUTPUT 4 ZONE ...

B2 - INPUT SIGNAL B3 - INPUT SIGNAL B4 - INPUT SIGNAL B5 - INPU ...

B2 - INPUT SIGNAL B3 - INPUT SIGNAL B4 - INPUT SIGNAL B5 - INPUT ...

J1 J2 A2146 NOTE: IF THE POWER SU ...

J1 J2 A2147 NOTE: IF THE POWER SU ...

X5200 DETECTOR ALARM 24 VDC + – WIRING NOTES: 1 IN NORMAL OPERATION WITH NO FAULTS OCCURRING, THE FAULT RELAY COIL IS ENERGIZED AND THE CONTACTS ARE CLOSED. 2 ALARM RELAY IS NORMALLY DE-ENERGIZED WITH NO ALARM CONDITION PRESENT. 3 INDIVIDUAL MANUAL oi TEST SWITCHES CAN BE INSTALLED REMOTELY OR A DETECTOR SELECTOR AND ACTIVATION SWITCH CAN BE INSTALLED AT THE FIRE PANEL. TEST SWITCHES ARE NOT SUPPLIED. (TEST SWITCHES ARE NOT NEEDED IF MAGNETIC oi IS USED.) 4 REFER TO SPECIFICATIONS SECTION FOR EOL RESISTOR VALUES. REFER TO EOL RESISTORS SECTION FOR INSTALLATION DETAILS. 5 PROPERLY CERTIFIED HAZARDOUS LOCATION ME ...

terminal block will not be affected by the heat generated by EOL resistors, observe the following guidelines when installing the resistors. 1. Required EOL resistor power rating must be 5 watts minimum. NOTE EOL resistors must be ceramic, wirewound type, rated 5 watts minimum, with actual power dissipation not to exceed 2.5 watts. This applies to ATEX/IECEx installations only. 2. Resistor leads should be cut to a length of approximately 1 1/2 inches (40 mm). 3. Bend the leads and install the EOL resistor as shown in Figure 13. 4. Maintain a 3/8 inch (10 mm) minimum gap be ...

displayed on the ZONE indicator on the controller front panel. 4. Press and hold the TEST button. The DETECTOR/ ZONE display indicates the counts per second (cps) received from the detector. If the counts per second exceeds 99, the FIRE LOGIC LEDs are illuminated to indicate that the number shown on the display must be multiplied by 10. The normal reading for an oi test is 80 to 110 cps. For a live fire test, 270 - 330 cps will be generated. A zero reading may indicate a dirty window, oi problem, faulty detector, or defective wiring. Release the TEST button, the ZONE and DETECTOR dis ...

recommended, since the product is not intended to be serviced and provides proper ingress protection to eliminate potential deterioration of the flamepaths. WARNING To avoid a potential electrostatic discharge (ESD), the painted surface of the detector should only be cleaned with a damp cloth. WARNING The sensor module (“front” half of the detector) contains no user serviceable components and should never be tampered with. To maintain maximum sensitivity and false alarm resistance, the viewing windows of the X5200 must be kept relatively clean. Refer to the following proced ...