GDS Compuprint 6214 Operation & User’s Manual

MAN10xxx-01 1 CONTENTS 1 Barcode Printer 001 1.1 1.2 Box Content Getting to Know Your Printer 001 002 2 Printer Setup 006 2.1 2.2 2.3 2.4 2.5 Open the Printer Loading the Ribbon Loading the Label Roll Module Connecting the Printer to the Host Computer Installing Printer Driver and QLabel with Super Wizard CD 006 007 012 014 016 ...

MAN10xxx-01 2 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial e ...

MAN10xxx-01 3 SAFETY INSTRUCTIONS Please read the following instructions carefully. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Make sure the printer is off before plugging the power connector into the power jack. 4. It is r ...

MAN10xxx-01 4 1 Barcode Printer 1.1 Box Content Please check that all of the following items are included with your printer:  Compuprint 6214 Barcode Printer  Label Stock  USB Cable  Compuprint 6214 Quick Guide  Ribbon Module Empty Ribbon Core  Power Adapter & Power Cord  Ribbon  AC Adapter  CD ...

MAN10xxx-01 5 1.2 Getting To Know Your Printer Device Overview Front View Rear View ...

MAN10xxx-01 6 Bottom View Notice **** Cut-outs are not intended for wall-mount use. . ...

MAN10xxx-01 7 The Internal View of Printer ...

MAN10xxx-01 8 The Printing Mechanism ...

MAN10xxx-01 9 2 Printer Setup 2.1 Open the Printer Open the Printer Cover and the Printing Mechanism Place the printer on a flat surface. Open the printer cover by pulling the release catches on both sides of the printer and lift the printer cover. ...

MAN10xxx-01 10 2.2 Loading the Ribbon A New Ribbon Module Installation 1. Attach the ribbon to the empty ribbon core with the adhesive strip at the end of the ribbon. 2. Insert the ribbon hub into empty ribbon core and new ribbon. Wind the ribbon around the empty ribbon core for 2 to 3 circles. 3. A ribbon module is ...

MAN10xxx-01 11 Load the Ribbon on the Printer For Ribbon Supply Module 1. Place the ribbon supply module into the printing mechanism. Please the left-hand side of ribbon hub first. Make sure the holder of ribbon hub is inserted into the notch. Then place the right-hand side of ribbon hub. ...

MAN10xxx-01 12 2. Unlock the release catch to close the printer cover. Push the release catch forward to unlock it. The ribbon supply module loading is completed. Load the Ribbon on the Printer For Ribbon Rewind Module ...

MAN10xxx-01 13 1. Open the cover of ribbon rewind mechanism. 2. Place the ribbon rewind module into the ribbon rewind mechanism. Please the left-hand side of ribbon hub first. Make sure the holder of ribbon hub is inserted into the notch. Then place the right-hand side of ribbon hub. ...

MAN10xxx-01 14 3. Turn the ribbon rewind wheel to tighten the ribbon until it has no wrinkles. 4. Close the cover of ribbon rewind mechanism. The ribbon loading is completed once the ribbon supply module and ribbon rewind module are assembled correctly. ...

MAN10xxx-01 15 2.3 Loading the Label Roll Module Load the Label Stock on the Printer 1. Unlock the ribbon catch and pull to open the label guide plate. 2. Place the label stock on label supply hubs. Make sure the label stock is aligned to both hubs. Adjust the label guide plates to fix the label width. Remember to push ...

MAN10xxx-01 16 3. Feed the Label through the label guides. The label guides will help to prevent the label swaying. 4. Unlock the release catch to close the printer cover. 5. Press the FEED key and make sure the label is fed smoothly. The label loading is completed now. Notice * Please keeps the rack gear clean to ensu ...

MAN10xxx-01 17 2.4 Connecting the Printer to the Host Computer 1. Please make sure that the printer is switched off. 2. Connect the power cord to the AC adapter. Connect the jack of the power adapter to the printer and connect the plug of the power adapter to the socket of the wall. ...

MAN10xxx-01 18 3. Connect the USB/serial cable to the printer and host computer. 4. Pressing the power button. The LED indicator should now lights up. ...