Crown Com-Tech CT-200 Service Manual

Text of Crown Com-Tech CT-200 Service Manual

Com-Tech 200 Amplifier Service Manual

1 COM-TECH ® 200 POWER AMPLIFIER SERVICE MANUAL K-SVCCT200 12-95 Com-Tech®, ODEP® and Crown® are registered trademarks of Crown International, Inc. Mailing Address: P.O. Box 1000 Elkhart, IN U.S.A. 46515- 1000 Shipping Address: 57620 C.R. 105 Elkhart, IN U.S.A. 46517 ©1995 by CROWN INTERNATIONAL, INC. Model CT200B
Com-Tech 200 Amplifier Service Manual 2 À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ PAS LES COUVERTURES. RIEN DES PARTIES UTILES À L’INTÉRIEUR. DÉBRANCHER LA BORNE AVANT D’OUVRIR LA MODULE EN ARRIÈRE. TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DISCONNECT POWER CORD BEFORE REMOVING REAR INPUT MODULE TO ACCESS GAIN SWITCH. CAUTION AVIS WARNING TO
Com-Tech 200 Amplifier Service Manual 3 Table of Contents Introduction ............................................................ 4 Parts Information .................................................... 5 Specifications ......................................................... 6 Theory .................................................................... 7 Electrical Checkout Procedures ........................... 12 Parts List (Non Module) ..............
Com-Tech 200 Amplifier Service Manual 4 Crown Technical Support Group Factory Service Parts Department Mailing Address: PO Box 1000 Elkhart, IN USA 46515-1000 Shipping Address: 57620 C.R. 105 Elkhart, IN USA 46517 Phone: (219) 294-8200 Toll Free: (800) 342-6939 FAX: (219) 294-8301 This manual contains service information on Crown power amplifiers. It is designed to be used in conjunc- tion with the applicable Owner's Manual. However, some important i
Com-Tech 200 Amplifier Service Manual 5 Parts Information ment on a C.O.D. or pre-payment (check or credit card) basis. Terms Normal terms are pre-paid. Net-30 Days applies to only those firms having pre-established accounts with Crown. If pre-paying, the order must be packed and weighed before a total bill can be established, after which an amount due will be issued and shipment made upon receipt of pre-payment. New parts re- turned for credit are subject
Com-Tech 200 Amplifier Service Manual 6 Specifications Unless noted otherwise, all specifications are based on driving an 8 ohm load per channel, both channels driven, the sensitivity switch in the 26dB position, the AC supply is 120VAC at 60Hz. Crown specifications are guaranteed through the warranty period (normally 3 years). Because our testing methods are more strin- gent than our published specifications, every Crown amplifier will exceed its publishe
Com-Tech 200 Amplifier Service Manual 7 Theory Overview It should be noted that over time Crown makes im- provements and changes to their products for various reasons. This manual is up to date as of the time of writing. For additional information regarding these amplifiers, refer to the applicable Technical Notes provided by Crown for this product. This section of the manual explains the general opera- tion of a typical Crown power amplifier. Topics cover
Com-Tech 200 Amplifier Service Manual 8 Theory Voltage Amplification The Voltage Translator stage separates the output of the Error Amp into balanced positive and negative drive voltages for the Last Voltage Amplifiers (LVAs), translating the signal from ground referenced ±15V to ±Vcc reference. LVAs provide the main voltage ampli- fication and drive the High Side output stages. Gain from Voltage Translator input to amplifier output is a factor of 25.2.
Com-Tech 200 Amplifier Service Manual 9 biased off. When the drive signal is negative going, the HS PNP conducts to deliver -Vcc to the load and the HS NPN stage is off. The output of the +LVA drives the base of predriver device. Together, the predriver and driver form the first two parts of the three-deep Darlington and are biased class AB. They provide output drive through the bias resistor, bypassing the output devices, at levels below about 100mW. An R
Com-Tech 200 Amplifier Service Manual 10 When the amplifier output swings positive, the audio is fed to an op-amp stage where it is inverted. This inverted signal is delivered directly to the bases of the positive (NPN) and negative (PNP) LS predrivers. The negative drive forces the LS PNP devices on (NPN off). As the PNP devices conduct, Vce of the PNP Darlington drops. With LS device emitters tied to ground, -Vcc is pulled toward ground reference. Since
Com-Tech 200 Amplifier Service Manual 11 Theory NEGATIVE LOW SIDE OUTPUT PNP STAGE POSITIVE LOW SIDE OUTPUT NPN STAGE NEGATIVE HIGH SIDE OUTPUT PNP STAGE POSITIVE HIGH SIDE OUTPUT NPN STAGE HIGH SIDE BIAS SERVO +LVA -1 -LVA -1 +VOLTAGE TRANSLATOR -VOLTAGE TRANSLATOR OUTPUT DEVICE EMULATION PROTECTION ERROR AMP VGS BGS BALANCED INPUTS INVERTING BRIDGE BALANCE LOW SIDE BIAS DIODE STRING -1 -1 MAIN NEGATIVE FEEDBACK (NFb) LOOP Figure 3. Typical Crown Amplifie
Com-Tech 200 Amplifier Service Manual 12 Electrical Checkout Procedures General Information The following test procedures are to be used to verify operation of this amplifier. DO NOT connect a load or inject a signal unless directed to do so by the proce- dure. These tests, though meant for verification and alignment of the amplifier, may also be very helpful in troubleshooting. For best results, tests should be per- formed in order. All tests assume that
Com-Tech 200 Amplifier Service Manual 13 77 25.0 –10.00 10.00 78 25.6 –9.97 9.97 80 26.7 –9.91 9.91 82 27.8 –9.86 9.86 84 28.9 –9.80 9.80 86 30.0 –9.74 9.74 88 31.1 –9.69 9.69 90 32.2 –9.63 9.63 92 33.3 –9.57 9.57 94 34.4 –9.51 9.51 –ODEP Procedure: Measure pin 3 of J500 and, if neces- sary, adjust R121 to obtain V–ODEP as specified above. Measure pin 3 of J500 and, if necessary, adjust R221 to obtain V–ODEP as specified above. +O
Com-Tech 200 Amplifier Service Manual 14 Electrical Checkout Procedures Test 10: Slew Rate & 10 KHz Square Wave Spec: 17 - 25 V/µS, 8 ohm load. Initial Conditions: Controls per standard. Procedure: Load each channel to 8 ohms. Inject a 10 kHz square wave to obtain 35 Volts zero-to-peak at each output. Observe the slope of the square wave. It should typically measure 17-25 V/µS. Also, the square wave must not include overshoot, ringing, or any type of osc
Com-Tech 200 Amplifier Service Manual 15 Electrical Checkout Procedures Test 16: Signal to Noise Ratio Spec: ≥ 100 dB below 8 ohm rated continuous average 20-20kHz power. Initial Conditions: Controls per standard. Short inputs. Procedure: Load each channel to 8 ohms. Measure less than 290µV at the output of each channel (20 Hz-20 kHz bandpass filter). Test 17: Turn off Transients Spec: < 80mV across an 8 ohm speaker load Initial Conditions: Controls per
Com-Tech 200 Amplifier Service Manual 16 Supplimental Items CPN Item Quantity A10087-71012 Rack Screw, 10-32 x .75 8 C 3342-0 Feet, Selfstick Black 4 D 4137-2 Nylon Washer 4 A10086-70808 Screw, 8-32 x .5 (For volume cover) 2 A10101-12 Spacer, #8 x 5/16OD x 1/4L (For volume cover) 2 F11489-6 Plexiglass Plate (Volume cover) 1 K80636-2 CT Series Reference Manual 1 Power Supply CPN Item Quantity A10087-11028 Screw, 10-32 x 1.75 (For transformer) 4 C 10171-4 Br
Com-Tech 200 Amplifier Service Manual 17 Parts List (Non-Module) Back Panel Assembly CPN Item Quantity D 8367-1 Knob, .5 Dia. Level Control 2 A10086-10410 Screw, 4-40 x .62 2 A10086-70808 Screw, 8-32 x .5 4 A10094-2 Lockwasher, #4 Internal Star 2 A10100-7 Aluminum Spacer, .250OD x .140ID x .312L 2 A10109-70808 Screw, 8-18 x .5 4 A10214-4 Strain Relief 1 C10187-0 Strain Relief (For European Power Cord) 1 A11793-0105D Power Cord, 16-3 SJT Neon UL/CSA 1 A1079
Com-Tech 200 Amplifier Service Manual 18 Parts List (Non-Module) Main Chassis Assembly Cont. CPN Item Quantity C 6457-3 Screw, #8 x 3/8 2 C 6912-7 Tension Retaining Board Supports 2 C 6913-5 1" Spacer Toggle Nut, Plastic 2 C 6914-3 .75" Spacer Toggle Nut, Plastic 2 C 7705-4 Flat Cable Clamp 2 C 9491-9 Screw, 6-32 x .312 3 C 9953-8 Screw, 6-20 x .312 6 C10111-0 Button, Mtg. 2 D 7060-3 Sil Pad, 7 Mil 2.05 x .775 1 F11632-1 Bracket, Transformer Mtg. 1 F12642-

Crown Amplifier Owners Instructions: