Halytech microSpider2 Environmental Quick Start Manual
Text of the manual
Quick Start Guide
This guide is not a replacement for the User Manual. Please refer to the complete
microSpider2 manual available from our website: www.halytech.com.au
Once on the website, go to Products Data Loggers microSpider, and at the
bottom of the page select the ‘Downloads’ tab. From there you will be able to do
Installing a SIM Card
You need a SIM card to receive automatic e-mail and/or FTP reports from your
microSpider2 over the phone network. Halytech can provide fully functioning SIM cards
for you. Alternatively, you can source your own SIM card by contacting your preferred
mobile phone carrier and requesting a SIM card provisioned with a plan enabling
interne
To install a SIM card into the microSpider2 fitted with a SILVER SIM card holder:
1.
Remove the metal bar protecting the circuit board by gently lifting it out of the
grooves.
2.
If connected, disconnect the battery from the circuit board by squeezing the
locking latch and gently pulling the connector upwards.
3.
Insert the SIM card:
a.
Slide the SIM card
Connecting the Antenna and Power
1.
Take the pre-greased O-ring out of the plastic bag and feed the antenna and
power cables through it.
(Fitting the O-ring into the case will be discussed in the next section.)
2.
Connect the antenna by pressing the flying lead connector squarely onto the
gold circuit board antenna connector until it "clicks-in".
Connect t
NOTE: A video clip showing the case assembly is available at
www.halytech.com.au/images/downloads/microspider/o-ring.wmv
1.
Re-Insert the metal bar protecting the circuit board into the case grooves.
Make sure that antenna cable passes the bar on the same side as the battery
lead
2.
Insert the O-ring into the groove of the top (battery) half
Connecting Inputs and Outputs
BACK (SOLDER) END VIEW
Pin numbers are as shown above, when looking at the back (solder end) of the
connector with the notch facing upwards. Both connectors have identical pinouts.
I/O CONN 1 I/O CONN 2
I/O CONNECTOR 1
PIN
FUNCTION
COMMENT
1
SWITCH 1 / COUNTER 1 /
QUADRATURE 1A
Active is short to GROUND
2
ANALOGUE 1
0 – 2.4V or 4-20 mA range
3
GROUND
4
SWITCH 2 / COUNTER 2 /
QUADRATURE 1B
Active is short to GROUND
5
ANALOGUE 2
0 – 2.4V or 4 - 20 mA range
6
GROUND
7
SWITCHED POWER OUT
Driven by CONTROL 1, max 1A
8
EXTERNAL POWER IN
Nominal 12V 1A DC
I/
Using the Connectors
Some usage scenarios of the microSpider2 I/O connectors are outlined below:
Connect inputs as per manual:
o
Switch, event, counter and quadrature inputs - connected directly to
appropriate input and GROUND.
o
4-20mA – Connect directly between an available analogue input and
GROUND. External resistors are NOT required.
o
Voltage i
Connecting the microSpider2 to your PC
1.
You must use the special LANlink Communications cable.
2.
Turn your computer on and disconnect it from your network.
3.
Plug the round connector end of the cable into the communications connector
of the microSpider2. (When viewed from the front, the communication
connector is on the left.)
4.
Connect the Y-end of t
Configuring your microSpider2
Continuing on from the previous section, follow these steps to begin configuring your
microSpider2:
1.
Go to the “Change Setup” page
2.
Set the location name (E.g. to your site name)
3.
Set the date and time
4.
Set the username and password for security
5.
Configure and name the microSpider2 inputs as required
6.
Calibrat