Sub-Zero 400-2 Series Installation Information

(400-22)) Series Series 2-2 #3758410 - Revision C - May, 2014 Anti-Tip Components Installation (424-2) If anti-tip bracket needs to be installed, follow these steps (See Figure 2-1): 1. Locate and mark two wall studs at back of unit installation location. 2. Identify and mark proper height to clear uni ...

(400-22)) Series Series Installation Information 2-3 #3758410 - Revision C - May, 2014 Sub-Zero Unit Figure 2-3. Anti-Tip Components Wall Stud Wood Block Screws & L-Bracket Min. 3” (76.2 mm) Anti-Tip Components Installation (430-2) If anti-tip components (aka wood block / blocking kit) need be installed, follow these steps ...

(400-22)) Series Series 2-4 #3758410 - Revision C - May, 2014 Rear leveling legs will move only 1/16” (2 mm) for every 18 revolutions of the Phillips-head adjusting screw. Do not over torque. Use lowest torque set- ting on any power screwdriver. Do not turn rear lev- eling legs by hand, doing so w ...

(400-22)) Series Series Installation Information 2-5 #3758410 - Revision C - May, 2014 Figure 2-11. Kickplate Removal Figure 2-13. Adjusting Rear Levelers Kickplate Screw (2) Unit Leveling (430-2) NOTE: Unit must be installed before final leveling. If unit is anchored to cabinets, remove anchor screws before leveling, rein ...

(400-22)) Series Series 2-6 #3758410 - Revision C - May, 2014 Figure 2-15. Door / Top Cabinet Hinge Adjustment Figure 2-16. Door / Top Door Hinge Adjustment Cabinet Hinge Shipping Screws Door Adjustment (424-2, 424FS-2) NOTE: Unit must be level before adjusting door. NOTE: If 424FS-2 door needs adjus ...

(400-22)) Series Series Installation Information 2-7 #3758410 - Revision C - May, 2014 Door Stop Adjustment (427-2 & 427R-2) Models 427-2 and 427R-2 have a 90° door stop cam built into the hinge system. The 90° door stop cam is located in the center portion of the hinge. To adjust the stop, use a standard straight-blade sc ...

(400-22)) Series Series 2-8 #3758410 - Revision C - May, 2014 Figure 2-20. Poly Tape Removal Figure 2-21. Stainless Steel Door Panel Removal Poly Tape Door Gasket Door Frame Handle Screws SS Handle (Door Hinges & Screws - not shown) SS Panel Poly Tape Door Assy METAL DOOR PANELS MAY HAVE SHARP EDGES. ...

(400-22)) Series Series Installation Information 2-9 #3758410 - Revision C - May, 2014 Figure 2-23. Overlay Door Panel Removal Door Assy Poly Tape Panel Mounting Screws Overlay Panel SS Handle Shown (Handle may vary) Figure 2-22. Poly Tape Removal Poly Tape Door Gasket Door Frame Overlay Door Panel Removal and Installation ( ...

(400-22)) Series Series 2-10 #3758410 - Revision C - May, 2014 Figure 2-25. Door Panel Removal Figure 2-26. Drawer Panel Removal Drawer Panel Mounting Bracket - Upper Drawer Panel Mounting Bracket - Bottom Door Panel Removal and Installation (427-2 & 427R-2) Models 427-2 and 427R-2 are NOT supplied w ...

(400-22)) Series Series Installation Information 2-11 #3758410 - Revision C - May, 2014 Figure 2-29. Stainless Steel Door Panel Removal Panel Door Assy Handle Screw (Door Hinges & Screws - not shown) Handle Door closer is spring loaded and may recoil quickly when detached. Hinge-Side Panel Mounting Screw Handle Stand-off Pane ...