Purkeys DIRECT PLUS Installation Manual

Text of Purkeys DIRECT PLUS Installation Manual

P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net

CONTENTS General Information ..........................................................................................2 Diagrams .............................................................................................................3 Direct Plus .................................................................................................3 Direct Flex ..........................................

The Purkeys Direct™ nosebox system combines all the best features of

our original liftgate charging systems with a space-saving nosebox that helps standardize the front of the trailer. It also includes an interior light controller (harness sold separately) designed to turn the lights on inside a trailer and automatically shut them off either: • via a timer • if the truck starts • if the liftgate batteries drop to a low state of charge. The Direct
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE DIRECT PLUS DIAGRAMS

Note: The Direct Plus nosebox must be mounted with the wires facing down

to help prevent water intrusion. Direct Controller Mounting Complete. MOUNTING THE NOSEBOX Step 1: Mount the Direct nosebox at the front of the trailer via the mounting holes on the mounting plate. Note: Do not block the LED status decal on the side of the Direct when mounting the nosebox. Note: The mounting plate can be removed if space is an issue or if a standard bolt pattern is
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE Step 1: Route the Direct jacketed 4-conductor main harness for the DC/DC converter behind the front plate then behind the header plate through the air/electrical tube to the center channel. Step 2: Route the Direct jacketed 4-conductor main harness in the center channel toward the back of the trailer. Secure with wire ties or cable clamps as you go. Step 3: Once you are

Step 4: Position the Direct jacketed

4-conductor main harness so it will reach the 2-stud strip and all the slack has been taken up. Mark the jacketed 4-conductor main harness so it can be taken back out of the battery box to be terminated. Note: If your battery box includes a slide-out tray, include enough slack to allow the tray to fully extend without tugging the wire connections. Step 5: Pull the jacketed 4-conductor main harness out of the box (maki
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE Step 7: Apply the supplied 3/4 inch black heat shrink where the jacket was stripped off. Step 8: Strip 3/8 inch of insulation off all 4 wires. Step 9: Slide the supplied red 1/4 inch heat shrink over the orange, yellow, and black wires. Slide the supplied black 1/4 inch heat shrink over the white wire. Step 10: Crimp 3/8 ring terminals onto the white and black 8-gauge w

Step 11: Position the heat shrink

over the crimps and apply heat to the 4 terminals. • Connect the 8-gauge black wire to the red positive input stud. • Connect the 8-gauge white wire to the black ground stud. • Connect the 14-gauge orange wire to the liftgate (+) stud. • Connect the 16-gauge yellow wire to the ignition stud. Main Harness Installation Complete. Step 12: Re-route the jacketed 4-conductor main harness back into the battery box.
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE INTERIOR LIGHT INSTALLATION WITHOUT SEVERE SERVICE Step 2: Terminate the positive input with a #10 ring terminal and connect to the Interior light input power stud inside the nosebox (see Figure 1). These interior light instructions apply if you are installing the Purkeys interior light harness (Purkeys Part Number H-00522: 50 ft Interior Light Harness) to power interi

Step 1: Inside the nosebox, connect the severe service positive terminal to the

interior light input power terminal (see Figure 2) using a 10 gauge wire. INTERIOR LIGHT INSTALLATION WITH SEVERE SERVICE Step 2: Terminate the Interior light positive wire with a #10 ring terminal and connect to the Interior light input power (see Figure 2). Step 3: Terminate the Interior light negative wire with a #10 ring terminal and connect to Ground (see Figure 2). Int
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE These interior light instructions apply if your preferred power source is the 7-way auxiliary circuit. Refer to the images in this section to see how to wire the connections. • The connection wires MUST be 10 AWG or larger. • Connections MUST be made with ring terminals or eyelets. • Make sure each fastened connection is torqued to at least 48 in-lbs. • It is
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE If your trailer is being spec’d with a momentary switch at the back of the trailer (the momentary switch is not included in the Purkeys kit), wire the circuit as shown below using the supplied pigtail harness shown in the drawing below (Purkeys Part Number 800-196). If you are using the pigtail harness for interior lights, but not for telematics, trim off and heat sh

SEVERE SERVICE INSTALLATION

Installing Cables to the Nosebox (Direct Max Only) Step 1: Remove cover on the side of the DIRECT MAX. Step 2: Install 4-gauge cables as shown. Make sure each connection is torqued to 5 ft-lbs. Replace the side cover. Note: The mega fuse used here is a 200 amp fuse. Step 3: Route the 4-gauge red and black cables behind the front cover, then under the header plate through the air/electrical tube to the center channel. Importan
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net DIRECT NOSEBOX INSTALLATION GUIDE Step 1: Route the red and black 4-gauge cable toward the back of the trailer via the center channel. Secure with wire ties as you go. Step 2: When near the liftgate battery box, route the two 4-gauge red and black cables to the liftgate battery box. Again, secure the cables with wire ties as you go. Step 4: Mark how much excess will need to be cut off of the 4-gauge re

Purkeys Battery Charger Owners Instructions: