WilTec 62297 Operation Manual

Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us. ...

Item 62297 Page 2 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown. Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure that the operating manual is complete, faultless and up to date, ...

Item 62297 Page 3 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de Introduction Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instruc- tions carefully and make sure you have understood its content. Keep these operation instructions safe. General safety instructions Warnings and important safety instructions contained in this operation manual are not meant to cover all possible situations, but serve as a general guideline. Always use the device in all co ...

Item 62297 Page 4 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de When using the sandblaster, make sure • not to overreach yourself and to have a secure stance, otherwise you might be seriously injured; • to wear appropriate work clothing and work equipment, e.g., protective goggles, a dust mask, non-slip shoes, etc. • that all adjusting wrenches have been removed before you operate the device; • that all power switches are in the off position before you connect the device to the power supply. Always release the air accumulated inside the device, even if the hose has been removed. Al ...

Item 62297 Page 5 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de 1. Do not use quartz sand (or any other materials that contain more than 1 % of crystalline silicon dioxide) as abrasive material and replace it with less dangerous materials. 2. Dispose appropriate air measurement devices to measure the rate of craftsmen’s being ex- posed to dangerous materials. 3. Stop up the spread of dangerous material by taking suitable measures, e.g., by using blast cleaning systems and cabinets; thus, risks can be better controlled and people in the vicinity better protected from dangerous substances. ...

Item 62297 Page 6 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de Main components № Name 1 Hose holder 2 Tank 3 Handle 4 Hose connector 5 Wheel 6 Tank stand Assembly Handle 1. Align the holes in the upper part of the handle and the holes in the abrasive tank. 2. Slide a flat washer on a long screw and slide this screw through the holes of the handle and the abrasive tank. 3. Place a washer and lock nut on the end of the screw and tighten it by hand. 4. Repeat steps 2 and 3 for the other handle hole. 5. Firmly tighten the screw with a cross-head screwdriver and a wrench. Stand and wheels 1. ...

Item 62297 Page 7 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de 5. Place a washer on a short screw and insert the screw through the hose holder and the abrasive tank. 6. Place a washer and a counter nut on a screw and firmly tighten it with a cross-head screwdriver and a wrench. 7. Repeat steps 5 and 6 for the other hose holder hole. 8. Firmly tighten the screw mounted in step 2 with a cross-head screwdriver and a wrench. Blasting gun and abrasive hose 1. Place a hose clamp on either side of the abrasive hose. Firmly slide the abrasive hose end on the abrasive inlet of the blasting gun. 2. ...

Item 62297 Page 8 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de NOTE: The flow rate of the material can be irregular when starting the sandblasting gun for the first time. If the material is dry, the flow rate will normalise after a minute. 10. After finishing the sanding, release the control lever of the sandblasting gun. Switch off the air compressor. Maintenance Caution! Keep your sandblaster clean and protect it from being damaged. In order to clean the outer face of the sandblaster, wipe it clean with a clean, damp cloth and a mild detergent or solvent. Do not immerse the device in li ...

Item 62297 Page 9 http://www.WilTec.de http://www.aoyue.eu 06 2021-1 http://www.teichtip.de Exploded view and parts list № Name Qty. № Name Qty. 1 Tank 1 8 Washer 4 2 Tank handle 1 9 Screw 5 3 Base frame 1 10 Washer 5 4 Front hose holder 1 11 Nut 5 5 Wheel 2 12 Material hose 1 6 Axle 1 33 Sandblasting gun 1 7 Lock pin 2 Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH. ...