Broan 100HL Instructions Manual

File Specifications

Brand: Broan
Category: Fan
Model: 100HL (Instructions Manual), przxfxVuNByWA
File Type: PDF
File Size: —
Pages: 12 pages

Download Document

Get a high-quality, printable PDF version of this manual for offline use.

Download PDF Manual (12 pages)

⚠️ Download Safety: This PDF is completely safe to download (last scan date: 13/04/2026).

Read Online

Read the Broan 100HL Instructions Manual online using the built-in PDF viewer.

Key Pages of Document

WITH HEATER & LIGHT

READ AND SAVE THESE INSTRUCTIONS REGISTER YOUR PRODUCT ONLINE AT www.broan.com/register IMPORTANT INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING THIS HEATER. To reduce the risk of fire, electric shock, or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephon ...

2. Mount housing.

Extend hanger bars to the width of the framing. Hold fan in place with the hanger bar tabs wrapping around the bottom edge of the framing. Nail fan to framing or fasten with screws (not provided) through holes near nails. * To ensure a noise-free mount: Secure hanger bars together with screws or use a pliers to crimp mounting channels tightly around hanger bars. 1. Insert hanger bars. Four (4) sliding han ...

assembly up near

housing. Connect light plug from grille assembly to receptacle inside of housing. 9. Attach grille. Place grille/ reflector combination over protruding screw and fasten in place using acorn nut provided. HAND TIGHTEN acorn nut 1/4 turn after it is snug. 10. Install bulb. The unit accepts a 100-Watt (maximum) incandescent bulb. 5. Connect electrical wiring. Run 120 VAC house wiring to insta ...

Before using heater, make sure heater has been properly installed

according to installation steps beginning with the "TYPICAL IN- STALLATION" section on page 2. Use a 3-Function Control to operate the heater, fan, and light separately. See “Connect Wiring” for details. ...

The following maintenance and cleaning tasks can be performed

by the user. All other servicing must be performed by an autho- rized technician If you have any questions, please consult with our customer service department at: 800-558-1711. TO REPLACE BULB Remove lens by gently depressing sides and pull down. Use bulb rated up to 100 watts only. LUBRICATION The heater is permanently lubricated and never needs oiling or disa ...

Slide Mounting Channel

RH (2 req) 3 97017711 Slide Mounting Channel LH (2 req) 4 97016449 Duct Connector Assembly, 4” 5 98010407 Electrical Knockout Panel 6 99170245 Screw, #8-18 X .375” * (5 req) 7 99150471 Screw, Ground #10-32 X .500 PH HWH * (2 req) 8 97017713 Wire Panel Assembly 9 99420666 Wire Clip 10 99150415 Screw, 8B X .25 SL HX SR W * (4 req ...

CALEFACTOR Y LUZ

LEA Y CONSERVE ESTAS INSTRUCCIONES REGISTRE SU PRODUCTO EN LÍNEA EN www.broan.com/register PLANIFICACIÓN El ventilador funcionará con más eficiencia y menos ruido si se ubica en un sitio donde requiera el tramo de conductos más corto posible y un mínimo número de codos. Instale una tapa de techo o de pared que tenga un regulador de tiro integrado a fin de reducir los contratiros. Alimente la u ...

2. Monte la cubierta.

Abra las barras de suspensión hasta el ancho de la estructura. Sostenga el ventilador en su sitio envolviendo las lengüetas de las barras de suspensión alrededor del borde inferior de la estructura. Clave el ventilador a la estructura o sujételo con tornillos (no incluidos) a través de los orificios que están cerca de los clavos. * Para lograr un montaje silencioso: acople y fije las barras ...

10. Instale la

bombilla. La unidad acepta una bombilla incandescente de 100 watts (máximo). 8. Conecte la luz. Sostenga el conjunto de la rejilla cerca de la cubierta. Conecte el enchufe de la luz del conjunto de la rejilla al receptáculo dentro de la cubierta. 9. Fije la rejilla. Coloque el conjunto rejilla/reflector sobre el tornillo que sobresale, y fíjelo usando la tuerca de caperuza que se proporciona. APRIETE CON LA MANO l ...

Antes de usar el calentador, asegúrese de que esté instalado ad-

ecuadamente, de acuerdo con los pasos de instalación indicados en “INSTALACIÓN TYPICA” en la página 6. Utilice un control de 3 funciones para operar el calefactor, el ventilador y la luz por separado (vea los detalles en la sección “Conexión eléctrica”). ...

El usuario puede realizar las siguientes tareas de mantenimiento

y limpieza. Todos los demás servicios los debe realizar un técnico autorizado. Si tiene preguntas, consulte a nuestro departamento de servicio al cliente llamando al: 800-558- 1711. PARA REEMPLAZAR LA LAMPARA Quite el lente, presionando suavemente los lados y empuje. Use una bombilla de una capacidad nominal máxima de 100 vatios. LUBRICACIÓN El calentad ...

PIEZAS DE REPUESTO

Se pueden hacer los pedidos de las piezas de repuesto en nuestro sitio web. Visítenos en www.broan.com. Clave No. Pieza No. Descripción 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 ** ** 97017572 97017712 97017711 97016449 98010407 99170245 99150471 97017713 99420666 99150415 97017609 98010405 99020294 97017742 99260428 99260488 98010409 97020888 99080606 9902029 ...