Purkeys DIRECT FLEX Diagnostics Manual

Text of Purkeys DIRECT FLEX Diagnostics Manual

Purkeys DIRECT FLEX P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net

CONTENTS Direct Flex (no severe service cables) ..............................................................2 Direct Max (includes severe service cables) ...................................................3 Cover Assembly ..................................................................................................4 Interior Light Module (optional) .................................................
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE DIRECT MAX (INCLUDES SEVERE SERVICE CABLES)
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE INTERIOR LIGHT MODULE (OPTIONAL) CONNECTIONS INSIDE NOSEBOX
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE NO LIGHTS ON FACE OF THE NOSEBOX Step 1: Confirm all connections are tight and inspect wiring for defects. Step 2: Connect the tractor to the unit. Step 3: Start the tractor. Step 4: Check the 2 amp fuse on the DC/DC converter in the battery box: • If blown, replace. • If good, proceed. Step 5: Using a voltmeter, measure the voltage at the 2-pin terminal strip on the DC/DC

Step 6: Check the 30 amp circuit

breaker using a voltmeter: • Place the positive lead on the circuit breaker stud that connects to the red junction stud closest to the DC/DC converter on the plate. • Place the negative lead on the negative post of the battery. • If there is a battery voltage reading, proceed to the next step. • If no voltage is shown, reset the circuit breaker. • If there is still no voltage, check wiring for defects. • If no
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE BATTERIES NOT BEING CHARGED Step 1: Connect the 7-way or dual pole cable to the trailer and start the tractor. • Place the voltmeter positive lead on the stud labeled as positive input. • Place the negative lead on the negative battery post. • Read the approximate tractor voltage. • If there is a voltage reading, proceed to the next step. • If there is no voltage re

Purkeys DIRECT FLEX Step 3: Unplug the 4-pin connector

from the DC/DC converter. • Place the voltmeter positive lead in pin #1 (12 v + input). • Place the negative lead in pin #3 (ground). • Read the approximate tractor voltage. • If there is a voltage reading, proceed to the next step. • If there is no voltage reading, inspect the wiring and plug and repair any issues. Step 4: Next: • Place the voltmeter negative lead in pin #3 (ground). • Place the positive
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE Step 5: Next: • Place the voltmeter negative lead on the negative battery post. • Place the positive lead on the red junction stud closest to the converter. • The voltage should read 13+ volts. • If voltage reads 13+, proceed to the next step. • If voltage does not read 13+, replace the wiring from the converter to the converter plug. Step 6: Next: • Place the volt

Step 7: Next:

• Place the voltmeter negative lead on the negative battery post. • Place the positive lead on the circuit breaker closest to the battery post. • The voltage should read 13+ volts. • If the voltage reads 13+, reset the circuit breaker. • If the voltage does not read 13+, the circuit breaker will not reset. Replace the circuit breaker. Step 8: On the front of the trailer, remove the hardware holding the cover assembly to the noseb
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE Step 9: Check the dual pole: • Place the voltmeter positive lead where the blue wire is connected. • Place the negative lead where the white wire is connected. • The voltage must be 13.2+ volts (13.8 volts is optimal). • If the voltage is 13.2+, inspect the wire for defects and replace if necessary. • If there is no voltage reading, skip to step 11. Step 10: Next: �

Step 11: Next:

• Place the voltmeter positive lead where the blue wire is connected. • Place the negative lead where the white wire is connected. • If there is a voltage reading, inspect the wiring for defects and replace if necessary. • If there is no voltage reading, proceed to the next step. Step 12: Next: • Place the voltmeter positive lead where the blue wire is connected. • Place the negative lead where the white wire is connected. •
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net FLEX/MAX DIAGNOSTIC GUIDE INTERIOR LIGHTS NOT WORKING (IF INSTALLED) The interior lights can be powered by liftgate batteries, dual pole, 7-way, reefer, etc. Step 1: Check for voltage at the interior light module: • Place the voltmeter positive lead on the blue wire. • Place the negative lead on the white wire. • There should be a power source voltage reading after closing the interior light swit

Purkeys Battery Charger Owners Instructions: