Pilot Communications EV Lite Manual 

Text of Pilot Communications EV Lite Manual 

17/01/2020 / DC1 / Version2

Tools required # Name Remark 1 Philips screwdriver Electric with bit preferred 2 Hex (M4) screwdriver Electric with bit preferred 3 Level – 4 Stainless steel anchors Size M10 5 Stainless steel bolts M10 to fit the anchors 6 Drill – 7 32A Type C Circuit Breaker – 8 5 core 6mm2 cable Length as required 9 Pencil – 2  +44 (0) 1606 59 66 22
17/01/2020 / DC1 / Version2 3 Prerequisites • This type of installation requires an electrical background. • When unpacking the contents of the kit, it is crucial to perform a visual check to confirm that none of the parts are damaged or broken. • Prior to installation, make sure to disconnect the main circuit breaker (CB). • Locate the serial number (S/N) on the attached test report and confirm that the same serial number is configured in the Char
17/01/2020 / DC1 / Version2 Make sure to always follow your local electrical regulations. The Pilot EV Lite installation should only be carried out by a certified installer. The below instructions are a guideline and provided for reference only. You are solely responsible for following all applicable electrical safety procedures, codes, methods, and materials provided as per the instructions below. Prior to installation, make sure to disconnect the main ci
17/01/2020 / DC1 / Version2 Place the wall mount on the designated wall. It is recommended to use a level to ensure that the template is aligned straight. Mark the holes with pencil. Mark the mount location 1 5 1 Mark the mount location 2 Drill holes Place the wall mount on the designated wall. It is recommended to use a level to ensure that the template is aligned straight. Mark the holes with pencil. Using a drill make the holes prior to installation. Co
17/01/2020 / DC1 / Version2 Insert appropriate screw anchors into the hole, ensuring that they fit the bolt size and wall type. Install screw anchors 3 Attach the bracket by application of bolts. Install the bracket 4 6  +44 (0) 1606 59 66 22
17/01/2020 / DC1 / Version2 Using the Hex screwdriver, unfasten six screws (three from each side) to dismantle the front panel. Dismantle the front panel 5 www.thepilotgroup.co.uk
17/01/2020 / DC1 / Version2 Dismantle the cable cover Insert the cable 6 7 Using the Philips screwdriver, unfasten the two screws to dismantle the cable cover. Insert the cable through the left hole and use the keystone cable clamp to secure it. 8  +44 (0) 1606 59 66 22
17/01/2020 / DC1 / Version2 Connect the cables according to the diagram: L = Brown N = Blue PE Earth \ PE \ Ground = Yellow Green Make sure to perform the appropriate PE connection test based on the current edition of the IET Wiring regulations. Connect the cable 8 ! www.thepilotgroup.co.uk
17/01/2020 / DC1 / Version2 Using the Hex screwdriver, fasten the six screws (three from each side) to assemble the front panel. Assemble the front panel 9 10  +44 (0) 1606 59 66 22
17/01/2020 / DC1 / Version2 Hang the device on the bracket and make sure it fits securely. Hang the device 10 www.thepilotgroup.co.uk
17/01/2020 / DC1 / Version2 Using the M4 screw and nut (included) securely fix the device to its location. Secure the device 11 12  +44 (0) 1606 59 66 22
17/01/2020 / DC1 / Version2 Switch on the main CB - Circuit Breaker (Switch I). Power up the device 12 www.thepilotgroup.co.uk
17/01/2020 / DC1 / Version2 Getting Started Step 1. Connect Nozzle Inspect the charger for any visible damage. Do not use the charger if damaged. Connect nozzle end to the car. Charging starts automatically. For the Pilot EV Lite Socket model, make sure that the other end of the cable is connected to the charger. Step 2. Remove Charger Do not unplug the charger while charging. Stop the charging process in the car. Release the latch on car’s charge port (
17/01/2020 / DC1 / Version2 Troubleshooting If charging slows down or stops unexpectedly, check the car’s infotainment for error messages. Unplug the charger from the car - Make sure the cable and nozzle are not damaged. Check the signaling light on the charger. The number of red flashing light may indicate the following issues: Single fast flashing – Problem with switching elements Two flashing lights – Problem with the residual current device Three

 www.thepilotgroup.co.uk  +44 (0) 1606 59 66 22

Pilot Group Limited, 15 Carnarvon Street Manchester M3 1HJ As a privately-owned business that has traded internationally since 1992 from our base in Manchester, we believe in working closely with our customers to form long lasting and mutually beneficial partnerships. At Pilot Group we believe in using technology to make the places we live and work SMART, SAFE and SUSTAINABLE. At Pilot Group we supply

Pilot Communications Automobile Accessories Owners Instructions: