rotork Remote Control Series Manual
Text of the manual
Top Quality Valve Actuators
Made in Sweden
Manual
SA PCU
RCEL
- 1 -
www.rotork.com www.remotecontrol.se
ELECTRICAL SHOCK HAZARD.To avoid serious personal injury,
property damage, turn off ALL power to the actuator before remov-
ing the cover.
Before installation or use, verify the nameplate information infor-
mation to insure the correct model number, torqu
- 2 -
www.rotork.com www.remotecontrol.se
PCU Board Specification
PCU Board - A
PCU Board - B (AC)
INPUT SIGNAL
SELECTION
AUTOSCAN
/SPAN
/ZERO
TIME
DELAY
DEAD
BAND
4-20mA DC
OUTPUT SIGNAL
4-20mA DC
INPUT SIGNAL
OUTPUT SIGNAL
CONNECTION
OPEN
AUTO
CLOSE
AC POWER 1
AC POWER 2
P3
P2
P1
POTENTIOMETER
INPUT SIGNAL
- 3 -
www.rotork.com www.remotecontrol.se
PCU Board - A
PCU Board - B (DC)
INPUT SIGNAL
SELECTION
AUTOSCAN
/SPAN
/ZERO
TIME
DELAY
DEAD
BAND
4-20mA DC
OUTPUT SIGNAL
4-20mA DC
INPUT SIGNAL
OUTPUT SIGNAL
CONNECTION
CCW
CW
OLS
CLS
OPEN
CLOSE
AUTO
POWER -
POWER +
P3
P2
P1
POTENTIOMETER
INPUT SIGNAL
- 4 -
www.rotork.com www.remotecontrol.se
What is DEAD BAND ?
It’s an area/band where no action occurs due to the actuator input.
If the user inputs 12mA (50%), the actuator is supposed to stop exactly at 50% poaition. The actuator repeats from open to close in
order to stop at 50% position at this point.
This is what we call hunting, and if the hunting e
- 5 -
www.rotork.com www.remotecontrol.se
Set up and Order
CONTROL / WARNING LAMP
Power On
Main Power Input
Power On / Off Flickering
CH1, CH2 in case of optional setting
Fault On / Off Flickering
Input defect/disconnection
Close On Lighting
Full Close
Open On Lighting
Full Open
Fault On Lighting&
Close On / Off Flickering
Potentiometer disconnection
Fault
- 6 -
www.rotork.com www.remotecontrol.se
LIMIT SWITCH Setting
Close / Open Limit Cam Switch Setting
1. With the power off, remove the cover and manually rotate
the ACTUATOR to the closed, clockwise, position.
2. Loosen the close cam set screw and rotate the cam in a
clockwise direction to actuate the close limit switch. Also, the
close auxiliar
- 7 -
www.rotork.com www.remotecontrol.se
Electrical wiring
1. Remove the ACTUATOR cover by loosening the four
captive cover bolts.
2. Confirm that the wiring diagram located in the
ACTUATOR and the wiring number on the nameplate
match with each other.
3. Confirm that the main power and supply described on
the nameplate of the ACTUATOR match with ea
- 8 -
www.rotork.com www.remotecontrol.se
5
INPUT is at 4-20mA 0-10V or 0-5V when change
DIP SWITCH setting to change to fit the table
1. DIP SWITCH Change
INPUT
1
2
3
4-20mA
ON
OFF
OFF
2 - 10V
OFF
ON
OFF
0 - 5V
OFF
OFF
ON
0 - 10V
OFF
ON
ON
1 - 5V
OFF
OFF
OFF
2. Optional Modulation
DIP SWITCH No.4 Button ON
3. 0V input, Push the ZERO BUTTON
ACTUATOR CLOSE
4