Yamaha P-2200/2201 Product Manual

Text of Yamaha P-2200/2201 Product Manual

ABOUT THIS MANUAL

SCOPE The P-2200 is a system oriented amplifier, made to be used in conjunction with mixers, consoles, frequency dividing networks and speakers — those made by Yamaha or by other manufacturers. Like any power amplifier, the P-2200's performance depends on system design and installation, in addition to its own capabilities. Thus, the P-2200 Operating Manual is system oriented, describing system design parameters and installation techniqu

THE P-2200/2201 BRIEF OPERATING INSTRUCTIONS

SECTION ONE INTRODUCTION SECTION TWO GENERAL SPECIFICATIONS SECTION THREE PERFORMANCE GRAPHS & A DISCUSSION OF SPECIFICATIONS SECTION FOUR THE DISTINCTION BETWEEN PROFESSIONAL AND HI-FI EQUIPMENT SECTION FIVE IMPEDANCE 1 OPERATING LEVELS 2 DYNAMIC RANGE 2 GAIN OVERLAP AND HEADROOM 4 INPUT SENSITIVITY RATINGS 4 PROFESSIONAL EQUIPMENT ADVANTAGES 4 INSTALLATION AND DETAILED OPERATION SECTION SIX PHYSICAL MOUNTING 1
THE P-2200/2201 BRIEF OPERATING INSTRUCTIONS Fig. 1A - P-2200 Front Panel Fig. 1B - P2201 Front Panel A. Input Attenuators Calibrated, stepped input attenuators lower input signal levels ahead of amplification stages. B. Peak Reading Meters (P-2200 only) Meters display instantaneous (peak) power output into an 8-ohm load over a full 50dB range; "0dB" = 100 Watts into 8 ohms. C. Thermal Warning Indicator Warns of overheating before thermal protection circui

Fig. 2A - P-2200 Rear Panel*

Fig. 2B - P2201 Rear Panel* A. Input Connectors The two XLR input connectors on each channel are unbalanced and are wired in parallel with each other and with the two phone jacks (tip/sleeve type). B. Input Polarity Switch Determines the polarity of the two XLR input connectors (Pin 2 or Pin 3 "hot"); does not affect the two phone jacks. See diagram on the rear panel. NOTES: 1. Input impedance is 25k-ohms minimum; +4dB (1.23V)

The P-2200 is not just "another big amplifier;" it is

an exciting new approach to high power sound. Yamaha's leadership is clearly demonstrated by the P-2200's pro- fessional features, sophisticated design, and uncom- promising performance. PEAK READING METERS* Instead of the more common and slow responding VU meters, the P-2200 has PEAK READING METERS that accurately display a full five decades (50dB) of output level. The peak meters have lar

Power Output Per Channel: (Refer to Figure 3. Ambient

room temperature for tests: 25-degrees Centigrade.) 200 Watts continuous average sine wave power into 8 ohms with less than 0.05% THD, (Total Harmonic Distortion), over a bandwidth of 20Hz to 20kHz, both channels driven. 230 Watts continuous average sine wave power into 8 ohms with less than 0.05% THD, at 1 kHz, both channels driven. Frequency Response: (Refer to Figure 5.) +0dB,

22-position, log-linear, detented, and dB-calibrated

INPUT ATTENUATORS (one per channel) attenuate input signal in 2dB steps from 0dB attenuation to -34dB, then steps of -37dB, -42dB, -50dB, infinity; Power (ON-OFF) switch; INPUT POLARITY switches. Fuses: AGC (3AG) type, 7-amps x 2 parallel fuses for the AC line input (U.S. and Canadian models). 4-amps x 2 parallel fuses for the AC line input (other territories' models). Dimensions: Mounts in a s

PERFORMANCE GRAPHS &

A DISCUSSION OF SPECIFICATIONS NOTE: In the discussion beginning on Page FOUR 5, references to specific specifications assume normal stereo operation (not mono operation) unless otherwise indicated. Normal (Stereo) Graphs Fig. 3 - Power Bandwidth vs Load Impedance Fig. 4 - Load Impedance vs Output Power Fig. 5 - Frequency Response vs Load Fig. 6A - T.H.D. vs Output Power at 8 Load Impedance (both channels driven) Fig. 6B - T.H.D. vs

Fig. 9 - Actual Output Impedance vs Frequency

Fig. 10 - Crosstalk (Channel Separation) Fig. 1 1 - Phase Response vs Frequency Fig. 12 - Power Consumption Fig. 13 - Peak Program Meter Accuracy (P-2200 only)

Yamaha P-2200/2201 Mono Mode Graphs

Fig. 14 - Power Bandwidth vs Frequency (Mono Mode) at 16 Load Impedance Fig. 15 - Load Impedance vs Output Power (Mono Mode) at 0.1% T.H.D., 1kHz Fig. 16 - Frequency Response (Mono Mode) at 16 Load Impedance Fig. 17 - T.H.D. vs Power Output (Mono Mode) at 16 Load Impedance Fig. 18 - T.H.D. vs Frequency (Mono Mode) at 16 Load Impedance Fig. 19 - Damping Factor vs Frequency (Mono Mode) at 16 Load Impedance Fig. 20 - Actual Output

Yamaha P-2200/2201 The following are actual oscilloscope photographs

made by an independent testing laboratory. The close vertical alignment of input and output traces in Fig. 21 through 23 depicts very low phase shift, so the amplifier will not alter musical wave shapes. Fig. 21 - 10Hz Square-Wave Response The output waveform displays very respectable low frequency response. The slight "tilt" shows a DC gain of unity, which prevents damage to speakers in the event any DC of

Types of Power Ratings

Peak power refers to the maximum undistorted power output of an amplifier. Most amplifiers cannot sustain their peak power ratings for long periods of time without external cooling fans. Because there are many different methods of rating an amplifier's peak power, it is hard to objectively compare the peak power ratings of two amplifiers. The peak power rating is primarily useful for determining an amplifier's ability to

Intermodulation Distortion, or I.M. is characterized

by the appearance in the output waveform of fre- quencies that are equal to sums and differences of integral multiples of two or more of the frequencies present in the input signal. The difference between inter- modulation distortion and harmonic distortion is that two or more different frequencies must be present to produce intermodulation distortion (only one frequency is needed for harmonic distortion

Yamaha P-2200/2201 HUM AND NOISE

Hum or noise from a power amplifier disrupts a program, and is irritating to a listener. Hum and noise could be considered a form of distortion. The P-2200's hum and noise are so low that they are completely inaudible under any normal listening circumstances. RISE TIME Rise time is a measurement of the amount of time an amplifier requires to respond to a square wave at a specified frequency. The rise time of an amplifier is an indication of i

Yamaha P-2200/2201 During the "overshoot" movement, the voice coil of

the loudspeaker interacts with the loudspeaker's magnetic assembly to produce a voltage called "back E.M.F." (electro-motive force). This action is similar to the operation of a dynamic microphone. If the amplifier's output impedance is low, this "back E.M.F." voltage is shunted through the amplifier's output circuits to ground, and back to the voice coil. Since the path from the voice coil, through the am

THE DISTINCTION BETWEEN

PROFESSIONAL AND HI-FI EQUIPMENT In most applications, a variety of auxiliary equipment will be connected to the P-2200, including: mixers, tape machines, compressors, graphic equalizers, echo, time delay, and reverb units, and just about any other audio electronics imaginable. Regardless of the function of auxiliary equipment, it will undoubtedly fall into one of two general categories, professional type or hi-fi type. The followin

Yamaha Amplifier Owners Instructions: