Vax V027 Operation & User’s Manual

Text of Vax V027 Operation & User’s Manual

Putting your cleaner together

Remove your Rapide XL from the carton with caution. The handle is connected to the body by a cord. Note: Do not tug or pull on the cord. Line up the handle to the upper body of the machine and slide into place. Secure from the back with the two smaller screws. Phillips screwdriver required a Handle b Solution trigger c Soap on/off d Power on/off e Clean water tank release f Clean water tank carry handle g Clean w

Putting your cleaner together

Feed the cord through the slots on the back of the handle and push into place. Place a nut into the recess in the back of the upper handle. While holding the nut in place insert one of the large screws through the front of the upper handle and tighten. Repeat the process with the second screw. Remove the backing tape from the screw cover and press into place. 1 2 1 Clean water tank Note: Make sure the cleaning soluti

Slide the tool caddy

downwards until it is secured in place. Note: The tool caddy can be removed for storage on a wall. 1 2 3 Pre-treating your carpets with the carpet treatment wand and solution Remove the clean water tank by pressing the clean water tank release and pulling the tank by the handle. Put to one side to fill later. While the clean water tank is removed, loosen the solution tank by gently pushing out the solution plug f

Remove solution tank cap.

CAUTION: Do not overfill. You should leave 1-2 cm of air space. Fill the tank with pre-treatment solution. Replace the solution tank cap. Return the solution tank to the cleaner making sure the solution tube lines up with the groove in the back of the solution tank. Firmly press the solution tube into the plug opening of the solution tank. 4 9 7 CAUTION: Maximum water temperature 40oC Remove the clean water tank cap and put

Pre-treating your carpets with

the carpet treatment wand and solution Using the wand and the trigger, apply pre-treatment solution to carpets. Turning the spray nozzle clockwise or anti-clockwise will alter the spray pattern. Caution: DO NOT turn the soap switch ON without solution in the tank. DO NOT allow the solution tank to run dry. To pre-treat carpets be sure that the unit is stood in the upright position. Turn the power and soap switches on. T

How to operate your

cleaner Remove solution tank cap. CAUTION: Do not overfill. You should leave 1-2 cm of air space. Fill the tank with VAX AAA Carpet Cleaner. The cleaner can be stored with solution in the solution tank. It does not have to be removed after each use. However the solution tanks should be rinsed out periodically. Note: One fill up of the solution tank will last for approximately 4 clean water reservoir fill ups. Replace the sol

How to operate your cleaner

Caution: DO NOT turn the soap switch ON without solution in the tank. DO NOT allow the solution tank to run dry. Plug the cord into an electrical socket. Step on the handle release pedal to put the cleaner into a cleaning position. Turn main power switch and soap switch to the ON position 4 How to operate your cleaner Burst clean feature To spray cleaning solution, depress the solution release trigger (3a) and move t

Put the cleaner in its upright

position. Turn the soap and power switches to the OFF position. Remove the hose from its stored position on the back of the cleaner. Lift the hose attachment cover located on the top of the dirty water tank. Insert the end of the hose into the tool opening and twist clockwise until it locks into place. 4 5 6 Attach the water supply connector into the hose water supply port at the side of the machine. Press fi

While depressing the blue solution spray

trigger, pull the attachment in a downward motion. Release the trigger and push the attachment forward in the same path to remove dirty water and solution from upholstery. For heavily soiled areas, repeat if necessary. To rinse, remember to turn the soap switch to the OFF position and repeat process. Note: Make sure upholstery is thoroughly dry before using. Remove the hose from the fitting by

Hard floor cleaning

20 21 Before assembling the accessories for hard floor cleaning, ensure that the cleaning solution soap tank is filled with Multi hard floor solution. Please refer to the bottle for measuring quanitites. Do not use Vax AAA carpet cleaner. N.B The Hydrodry head should only be used on sealed hard floors. If in doubt, consult the flooring manufacturer. Wrap the solution tube around the hose and secure into place using the clips provided. A

Vax Vacuum Cleaner Owners Instructions: