Toro 38614 Operator's Manual

Power Max® Snowthrowers Model No. 38614—Serial No. 311000001 and Up Model No. 38624—Serial No. 311000001 and Up Model No. 38624W—Serial No. 311000001 and Up Model No. 38634—Serial No. 311000001 and Up Model No. 38644—Serial No. 311000001 and Up Model No. 38654—Serial No. 311000001 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners or professional, hired operators. It is designed for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties. It is not designed for removing materials other ...

manual before operating the snowthrower . Become familiar with all controls and know how to stop the engine quickly . Operator 's Position The low-speed auger has a moving pinch point close to the opening. Caution: Improper use may result in loss of fingers, hands, or feet. There is a high-speed impeller close to the opening. This machine meets or exceeds the B71.3 specifications of the American National Standards Institute in effect at the time of production. Read and understand the contents of this manual before the engine is ever started. This is the safety alert symbol. It is used ...

from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such machinery on a trailer with a portable container, rather than from a gasoline dispenser nozzle. – Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open device. – Replace gasoline cap securely and wipe up spilled fuel. – If fuel is spilled on clothing, change clothing immediately. • Use extension cords and receptacles as specified by the manufacturer for all machines with electric starting motors. • Adjus ...

details if the machine is to be stored for an extended period. • Maintain or replace safety and instruction labels, as necessary. • Run the machine a few minutes after throwing snow to prevent freeze-up of the rotor blades. Toro Snowthrower Safety The following list contains safety information specific to Toro machines or other safety information that you must know. • Rotating auger/impeller can cut off or injure fingers or hands. Stay behind the handles and away from the discharge opening while operating the machine. Keep your face, hands, feet, and any other part of your body or clothing ...

dismemberment, auger hazards—keep bystanders a safe distance from the snowthrower. 112-6625 Reorder part no. 112-6629 1. Cutting/dismemberment hazard, impeller—do not place your hand in the chute; stop the engine before leaving the operator’s position, use the tool to clear the chute. 112-6626 (Models 38614 and 38624 only) 1. Traction drive—squeeze the lever to engage; release the lever to disengage. 3. Cutting/dismemberment hazard, impeller—do not place your hand in the chute; stop the engine before leaving the operator’s position, use the tool clear the chute. 5. Thrown object hazard ...

1. Stop 3. Fast 2. Slow Briggs & Stratton Part No. 275949 1. Choke on (Choke) 2. Choke off (Run) Briggs & Stratton Part No. 276925 1. Warning—read the Operator’s Manual. 3. Warning—toxic gas inhalation hazard. 2. Warning—fire hazard. 4. Warning—hot surface/burn hazard. Briggs & Stratton Part No. 277566 1. When starting a cold engine, close the choke and press the primer two times. 2. When starting a warm engine, open the choke and do not press the primer. Briggs & Stratton Part No. 277588 1. Primer 3. Ignition key out (Engine—Stop) 2. Ignition key in (Engine—Run) Briggs & Stratton Part No. 278866 1. Fuel� ...

Procedure Description Qty. Use Handle bolts 4 Curved washers 4 1 Locknuts 4 Install the upper handle. 2 No parts required – Install the wheel clutch cable ends 3 No parts required – Install the traction control linkage. Carriage bolts 2 4 Locknuts 2 Install the chute control rod. 5 Cable tie 1 Connect the wire to the headlight. 6 No parts required – Fill the engine with oil. 7 No parts required – Check the tire pressure. 8 No parts required – Check the skids and scraper. 9 No parts required – Check the operation of the traction drive. 7 ...

Parts needed for this procedure: 4 Handle bolts 4 Curved washers 4 Locknuts Procedure Note: Do not remove the rubber band on the cables until you have installed the upper handle. 1. Lift and rotate the upper handle and position it over the lower handle (Figure 3). Important: Route the cables attached to the Quick Stick inside the upper handle legs and ensure that the cables and the wire for the headlight are not pinched between the handle sections. Figure 3 1. Cables 2. Secure the upper handle with 4 handle bolts, 4 curved washers, and 4 locknuts from the loose parts bag (Figure 4). Figure 4 2 Installing the Wheel Clutch C ...

3. Remove the nut and washer from the handle, attach the cable clamp on the cable to the handle, install the washer and the nut, and hand tighten the nut (Figure 7). Figure 7 1. Cable clamp (2) Important: Ensure that the curved side of the cable clamp is against the handle and that the cable is routed below the clamp bolt. The cable must be in a straight line from the cable clamp to the point where it attaches to the wheel clutch lever. 4. Pull the cable jacket down gently until the wheel clutch lever is down and the slack is out of the cable, then tighten the cable clamp nut securely (Figure 8). Figure 8 5. Squeeze the l ...

3. Inner washer 2. Trunnion 4. Outer washer Note: To make installation easier, leave the flat washer on the trunnion (Figure 11). 4. Shift the speed selector lever into Position R2. 5. Rotate the lower link arm fully upward (counterclockwise) (Figure 12). Figure 12 6. Lift up on the speed control rod and insert the trunnion into the hole in the speed selector lever (Figure 11). Note: If the trunnion does not fit into the hole when you lift up on the speed control rod, rotate the trunnion upward or downward on the speed control rod until it fits. 7. Secure the trunnion and upper end of the speed control rod with the out ...

4. Insert the front end of the rod into the opening in the back of the chute gear cover until it slides into the chute gear (Figure 15). Figure 15 5. Align the holes in the nested ends of the rods and insert 2 carriage bolts (in the loose parts bag) through the short rod from the left side of the machine (from the operating position). 6. Insert the cable clip that supports the deflector cable onto the forward carriage bolt, and secure the carriage bolts with locknuts from the loose parts bag (Figure 16). Figure 16 1. Cable clip 2. Deflector cable 7. Hold the blue trigger cap down and rotate the Quick Sti ...

connector is on the bottom (Figure 17). 2. Secure a cable tie (from the loose parts bag) around the wire and the handle about an inch (2.5 cm) below the U-bolt (Figure 17). 6 Filling the Engine with Oil No Parts Required Procedure Your machine comes with oil in the engine crankcase. Note: Before starting the engine, check the oil level and add oil if necessary. Use automotive detergent oil with an API service classification of SF, SG, SH, SJ, SL, or higher. Refer to your engine owner’s manual. Use Figure 18 below to select the best oil viscosity for the outdoor temperature range expected: Figure 18 1. Us ...

Scraper No Parts Required Procedure Refer to Checking and Adjusting the Skids and Scraper in Maintenance. 9 Checking the Traction Drive Operation No Parts Required Procedure CAUTION If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage. Carefully check the traction drive and adjust it properly, if necessary. 1. Start the engine; refer to Starting the Engine. 2. Move the speed selector to Position R1; refer to Operating the Speed Selector. 3. Squeeze the left hand (traction) lever to the hand-grip (Figure 20). Figure 20 The machi ...

12. Skid (2) 4. Quick Stick™discharge chute control 13. Electric starter button 5. Traction lever 14. Electric starter plug-in 6. Fuel tank cap 15. Snow cleanout tool 7. Engine oil fill tube/dipstick 16. Headlight 8. Chute deflector 17. Wheel clutch lever (2; models 38634, 38644, and 38654 only) 9. Discharge chute Figure 22 1. Choke 5. Recoil starter 2. Ignition switch 6. Oil drain plug 3. Fuel shutoff valve 7. Primer 4. Throttle Figure 23 1. Snow cleanout tool (attached to the handle) Operation Note: Determine the left and right sides of ...

Starting the Engine 1. Check the engine oil level. Refer to Checking the Engine Oil Level in Maintenance. 2. Turn the fuel shutoff valve 1/4 turn counterclockwise to open it (Figure 25). Figure 25 3. Insert the ignition key (Figure 26). Figure 26 1. Ignition key 4. Firmly push in the primer with your thumb 2 times (15°F or -9°C or above) or 4 times (below 15°F or -9°C), holding the primer in for a second before releasing it each time (Figure 27). Figure 27 5. Rotate the choke to the Choke position (Figure 28). 15 ...

Figure 29 7. Start the machine pulling the recoil starter or pressing the electric-starter button (Figure 30). Figure 30 1. Electric-starter button 3. Recoil starter 2. Electric starter plug-in Note: To use the electric starter, connect a power cord to the electric starter plug-in first and then to a power outlet. Use only a UL-listed, 16-gauge extension cord recommended for outdoor use that is not longer than 50 feet (15 m). WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before using the machine. If the cord is damaged, do ...

the recoil starter from freezing up. Operating the Traction Drive CAUTION If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage. Carefully check the traction drive and adjust it properly, if necessary; refer to Checking the Traction Drive Operation in Setup for more information. Important: If the machine moves when the traction lever is in the released position, check the traction cable (refer to Checking and Adjusting the Traction Cable) or take the machine to an Authorized Service D ...

The speed selector has 6 forward and 2 reverse gears. To change speeds, release the traction lever and shift the speed selector lever to the desired position (Figure 36). The lever locks in a notch at each speed selection. Figure 36 Operating the Auger/Impeller Drive 1. To engage the auger/ impeller drive, squeeze the right hand (auger/ impeller) lever to the handgrip (Figure 37). Figure 37 2. To stop the auger and impeller, release the right hand lever. Important: When you engage both the auger/impeller lever and the traction lever, the traction lever locks the auger/impeller lever down, freeing your right hand. To release ...

Discharge Chute Latch. • If the chute does not turn as far to the left as it does to the right, ensure that the cable is routed to the inside of the handles. Refer to Installing the Upper Handle. • If the chute does not lock into place when you release the trigger cap, refer to Adjusting the Discharge Chute Latch. Moving the Chute Deflector Hold the blue trigger cap down and move the Quick Stick forward to lower the chute deflector; move it rearward to raise the chute deflector (Figure 40). Figure 40 Unclogging the Discharge Chute If the auger/impeller is running but there is no snow coming out ...

throwing snow. • If the engine slows down under a load or the wheels slip, shift the machine into a lower gear. • If the front of the machine rides up, shift the machine into a lower gear. If the front continues to ride up, lift up on the handles. • The pivoting scraper on the machine is not recommended for use on gravel surfaces. But if you must use the machine on a gravel surface, adjust the skids further down to prevent the pivoting scraper from picking up rocks. Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance S ...