Xantech DL85K Installation Instructions Manual
Text of Xantech DL85K Installation Instructions Manual
Dinky Link™ Surface Mount
Plasma\LCD\LED\CFL Friendly
IR Receiver
1
DESCRIPTION
These small IR receivers have been designed for mounting in very small
spaces. They may be mounted under shelf edges, cabinet ledges, in wall
speakers, etc. – anywhere an inconspicuous appearance is desired. The high
sensitivity of these receivers allows placement behind speaker grilles and still
receive IR commands up to 80 feet away*.
FEAT
A typical system will use an IR receiver, several emitters, and a power supply
all connected to a connecting block.
1. Connect the IR receiver to the “IR RCVR” port on the connecting
block. The ‘red’ connector is installed to the ‘red’ plug.
Note: In some extended distances, additional 3-conductor may be
required and can be connected to the terminals on the connecting
block.
2. Connect the Emitters to the connecting b
LOCAL SYSTEM APPLICATION
Another application is to locate the IR receiver in a central location, such as
the TV, video screen and/or a speaker. The audio/video equipment can then
be hidden inside a cabinet or located away from the front of a room. This will
give the end-user the ability to direct a remote control to one central location
and not have to worry about aiming to the respective device to be controlled.
The IR receiver is in close proximity to
ITEM C: (4) 283D Designer Emitters
ITEM D: (1) 781ERGPS Power Supply
STEP 1:
Plug in the 2.1mm Coaxial power plug of the 781ERGPS Power Supply (ITEM
D) into the jack labeled 12VDC on the 789-44 Connecting Block (ITEM B).
Plug the AC end of the 781ERGPS Power Supply (ITEM D) into a ‘un-
switched’ 120V AC Line outlet.
STEP 2:
Connect the 3.5mm stereo mini plug from the 481D IR Receiver (ITEM A) to
the ‘IR RCVR’ input located on the 789-44 Connectin
IR Troubleshooting Guide
NOTE: Due to the many variables in a given installation, the
troubleshooting countermeasures you will have to take may vary from job
to job. Each installation is different due to the number of IR receivers in
use, length of wire runs, type of wire, amount of ambient IR noise present,
etc…. Therefore, your countermeasures for a particular job will range
from nothing at all, to any combination of the solutions listed below.
IR R
Symptom #3: TB LED on IR Receiver (and/or Emitters) on solid
Cause:
Solution
1. Plasma Interference
Use a 85 or 95 series Plasma 'Friendly'
Receiver. If already using a this unit, please
note the Plasma interference can be reflected
off of any item it comes into contact with within
approx. 3ft. From the front of the display.
Keeping this in mind, make sure that the IR
receiver is free from any obstruction that might
reflect back into the receiving eye
Xantech DL85K Symptom 6: Emitters function but some (or all) components do not
respond.
Cause:
Solution
1. Emitter placement is incorrect.
Reposition the Emitter so that it is directly
over the components sensor window.
Consult the components owners’ manual of
the unit for the exact location of the IR
Sensor Window.
2.
Emitter placement is correct
but the signal is overpowering
the unit or there is bleed-
through from other emitters
close by.
Reposition the Emitt
Xantech DL85K Xantech® warrants its products to be free of defects in materials or workmanship. This is a
Limited Lifetime warranty from the date of purchase by the original consumer. Any products
returned to Xantech and found to be defective by Xantech within the warranty period will be
repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the
actual cost of installation or removal of the product, nor for an