Sebo Automatic X1 Operation & User’s Manual

© Copyright SEBO America, LLC • All rights reserved. Series ENGLISH ...

Water lift (at motor) 92 inches Airflow (at motor) 103.8 CFM Filter bag capacity 1.4 gal. Sound level 69 dBA Body weight X4-16.7 lbs / X5-16.9 lbs Motor protection electronic cut-out Working width X4-12 inches / X5-15.1 inches Brush drive toothed belt Brush speed 3100 rpm Floor adjustment automatic sensor control Cord length 40 feet Radio suppression EN 55014 Verf. 242/91 Technical Details Technical Details 2 Wiring Diagram 2 Important Safety Instructions 3 Special SEBO Product Features 4 Automatic Power Head Height Adjustment 4 Brush Roller Obstruction – A ...

outlet when not in use and before servicing. 2. Do not use outdoors or on wet surfaces. 3. Do not use near small children or pets. Do not allow to be used as a toy. Use of this product by children should always be supervised by an adult. 4. Use only as described in this manual. Use only manufacturer-recommended attachments. 5. Do not use with a damaged cord or plug. If vacuum is not working as it should, has been dropped, damaged, left out-doors, or dropped into water, take it to a SEBO service center. 6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord ar ...

the world. Along with its excellent filtration system (99.9% to 0.3 microns), one of its most important features is its ability to “monitor” the resistance of the brush roller against the floor, so that the proper cleaning height is consistently maintained. In addition, the machine has warning systems and automatic shut-off capabilities that are designed to alert the user to machine problems that, if ignored, will damage the machine or diminish performance. Your SEBO automatic’s five most unique features are: 1. Automatic Power Head Heigh ...

2. On/Off switch 3. Handle assembly 4. Retaining ring 5. Cover release flap 6. Dust bag housing 7. Front cover 8. Housing release button 9. Power head with brush 10. Cable (cord) 11. Attachment tube handle 12. Attachment hose 13. Handle catch 14. Carrying handle 15. Cable (cord) hook 16. Attachment tube (active wand) 17. Crevice nozzle 18. Upholstery nozzle 19. Foot pedal 20. Swivel neck 21. Support lever 22. Projection tab 23. Connecting tube Identification of Parts Place the power head (9) on the floor with the swivel neck (20) and the support lever (21) upright. Hold the dust bag housing (6) vertically and place it over the swi ...

A. Before turning on your vacuum cleaner, make sure that the vacuum handle is in its upright locked position and that you have a firm hold on the handle grip to keep the machine from moving forward. 1. Turn the quick release cable hook (15) to the up position by moving it to the left or right. 2. Release the power cord plug from the power cord and lift the cord off of the upper cord hook (26). 3. With the switch (2) in the “O” (OFF) position, plug the polarized power cord into a 120 volt outlet located near the floor. Switch Position O = OFF I = ON Operating Positions B. When the machine is switched on with the handle in ...

areas.The handle grip (1) should be in the upright, locked position (as shown in figure 1). Grip the attachment tube handle (11), pull it up and away from the machine and stretch out the hose (12) until it locks to the back of the tube (this locking action will prevent the hose from retracting back into the attach- ment tube while it is in use). Various attachments may be inserted onto the end of the tube. After use, remove attachment and re-insert the attachment tube into the back of the machine. Be sure that the attachment tube han- dle (11) is inserted over the project ...

To change the dust bag, pull the cover release flap forward (#5 on page 5) and lift the cover (7) from the dust bag housing. The cover release flap must remain in a for- ward “pulled-out” position to change dust bags and lock them into place. Squeeze the clamps on both sides of the dust bag sealing plate, slide the plate (28) from the holder (29) and push the cap on to seal the bag. Slide the sealing plate (28) of a new bag into the holder and push it in firmly. Re-insert cover into dust bag housing, push it for- ward, then lock it in place by pushing down the cover release flap. You may find it convenient to ...

Blockages in the hose can be cleared by removing the attachment hose (12) from the machine by squeezing the retaining ring (4) and inserting the oppo- site end of the hose in the connecting tube (23). Hold the hose upright with one hand blocking the top end and switch on the machine. If necessary, quickly lift your hand on and off the end of the hose. If this procedure does not clear the clog, a straight wire can be inserted into the hose to push out the clog. Take care not to puncture the hose with the wire. Clogs in the Airflow Pathway - Figure 12 Most clogs can be removed by accessing the airflow pathw ...

or machine shuts off intermittently Bag full or clog light on or flashing & machine shuts off Brush light on Brush light slowly flashing Brush light flashing & machine shuts off Up & down lights flicker Does not pick up Front bag door won’t fully close Hose doesn’t retract after attachment tube is inserted REASON 1. Handle not fully inserted into the bag housing, causing a faulty connection. 2. Not plugged into good outlet. 3. Cable worn. 4. Dust bag housing (6) not seated fully into proper “locked” position on top of power head. 1. Bag full. 2. Clog in airflow pathway, attach- ment hose, attachment tube, swivel ...

2 5297 SE Handle grip (incl. pos. 7+10) 3 5359 DG Grommet 4 5450 DG Power supply cord 5 05112 Switch 6 5160 HG Switch cap (light gray) 7 5161 DG Switch cap holder 8 5162 Cable clamp 9 0103 Screw C 3.9x16 DIN 7981 10 5253 UL Wire-antistatic 11 5298 ER Handle cable 12 0129 Screw M 4x12 DIN 966 13 5187 Handle tube 14 0102 Screw F 3.9x13 DIN 7981 15 5040 HG Hose, cpl. 16 5045 DG Extension tube 17 5707 GW Cover (white) 18 5319 Bag holder Spring 19 5706 DG Cover release (dark gray) 20 5091 Safety catch spring 21 5360 Safety catch 22 5324 Bag holder cpl. (incl. ...

(white/dark gray) 101 5712 GW Exhaust filter catch (white) 102 5143 Exhaust filter 103 5711 GW Exhaust filter cover (white) 104 5729 UL Swivel neck assembly 105 5176 UL Male contact holder 106 0102 Screw F 3.9 x 13 DIN 7981 107 2494 Cable clamp 108 5101 Swivel neck bearing r. h. 109 5178 Swivel neck support r. h. 110 5728 Swivel neck support l. h. 111 5717 Swivel neck bearing l. h. 112 5203 ER PCB 12 V power supply 113 5205 Ribbon cable 114 5713 GW Brush roller release 115 5103 Spring 116 5051 DG Axle, assembly 117 5059 DG Foot pedal 118 5053 Axle 119 5055 DG Wheel 12 ...

(white/dark gray) 101 5712 GW Exhaust filter catch (white) 102 5143 Exhaust filter 103 5711 GW Exhaust filter cover (white) 104 5729 UL Swivel neck assembly 105 5176 UL Male contact holder 106 0102 Screw F 3.9 x 13 DIN 7981 107 2494 Cable clamp 108 5101 Swivel neck bearing r. h. 109 5178 Swivel neck support r. h. 110 5728 Swivel neck support l. h. 111 5717 Swivel neck bearing l. h. 112 5203 ER PCB 12 V power supply 113 5205 Ribbon cable 114 5713 GW Brush roller release 115 5103 Spring 116 5051 DG Axle, assembly 117 5059 DG Foot pedal 118 5053 Axle 119 5055 DG Wheel 12 ...

Three Years Non-Wear Parts - One Year Labor EXCLUSIVE REMEDY: The remedies provided under the terms of this Warranty are the purchaser’s exclusive remedies and are in lieu of any other remedies otherwise available. THE WARRANTY DOES NOT COVER: • Used or secondhand products. • Products outside of the warranty period. • Items not manufactured by SEBO. • Normal maintenance service. • Equipment damaged by improper use, accident, other casualty or negligence. • Machines equipped with nonauthorized attachments or modifications. • Machines on which the serial number has been altered ...