Sharp R-580D Service Manual

Text of Sharp R-580D Service Manual

In interests of user-safety the oven should be restored to its

original condition and only parts identical to those specified should be used. TABLE OF CONTENTS Page CAUTION, MICROWAVE RADIATION............................................................................................................. 1 WARNING ...............................................................

GENERAL IMPORTANT INFORMATION

This Manual has been prepared to provide Sharp Corp. Service engineers with Operation and Service Information. It is recommended that service engineers carefully study the entire text of this manual, so they will be qualified to render satisfactory customer service. CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR OR OTHER PARTS CONDUCTING

230 - 240 Volts

50 Hertz Single phase, 3 wire earthed Power Consumption 1.55kW Power Output 1000 watts nominal of RF microwave energy (IEC Test Procedure) Operating frequency 2450 MHz Case Dimensions Width 495 mm Height 355 mm including foot Depth 525 mm Cooking Cavity Dimensions Width 450 mm Height 222 mm Depth 432 mm Turntable diameter 406 mm Control Complement Touch Control System Clock ( 1:00 - 12:59) Timer

1. Door handle

2. Touch control panel 3. Digital readout 4. See through door 5. Door seals and sealing surfaces 6. Door safety latches 7. Door hinges 8. Coupling 9. Menu label 10.Oven lamp 11.Waveguide cover 12.Turntable tray 13.Turntable support 14.Ventilation openings 15.Power supply cord NOTE: The directed features are disabled after three minutes when the oven is not in use. These features are automatically enabled when the doo

Closing the door activates all door interlock switches

(1st. latch switch, 2nd. latch switch and stop switch). IMPORTANT When the oven door is closed, the monitor switch contacts (COM-NC) must be open. When the microwave oven is plugged in a wall outlet, rated voltage is supplied to the noise filter and the control unit. Figure O-1 on page 28 1. The display shows "SHARP MICRO-WAVE OVEN". 2. To set any programmes or

An example of how sensor works:

1. Potatoes at room temperature. Vapor is emitted very slowly. 2. Heat potatoes. Moisture and humidity is emitted rapidly. You can smell the aroma as it cooks. 3. Sensor detects moisture and humidity and calculates cooking time and variable power. Cooking Sequence. 1. Touch each SENSOR COOK or SENSOR INSTANT REHEAT function pad to operating the sensor cooking. (See the operation manual for the proper procedure.) NOT

FUNCTION OF IMPORTANT COMPONENTS

defect in the control unit, the thermal cut-out will open. Under normal operation, the oven thermal cut-out remains closed. However, when abnormally high temperatures are reached within the oven cavity, the oven thermal cut-out will open at 125˚C, causing the oven to shut down. The defective thermal cut-out must be replaced with new one. MAGNETRON THERMAL CUT-OUT The thermal cut-out located near the magnetron is

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts of the high voltage circuit will result in electrocution. High voltage capacitor, Power transformer, Magnetron, High voltage rectifier assembly, High voltage fuse, High voltage harness. REMEMBER TO CHECK 3D 1) Disconnect the supply. 2) Door opened, and wedged open. 3) To discharge the high volta

Sharp R-580D CK = Check / RE = Replace

MAGNETRON POWER TRANSFORMER H.V. RECTIFIER ASSEMBLY HIGH VOLTAGE CAPACITOR 1ST. LATCH SWITCH 2ND. LATCH SWITCH STOP SWITCH MONITOR SWITCH MONITOR RESISTOR THERMAL CUT-OUT 125˚C FAN MOTOR TURNTABLE MOTOR FUSE M10A TOUCH CONTROL PANEL KEY UNIT RELAY (RY-1, RY-2) FOIL PATERN ON P.W.B. POWER SUPPLY CORD SHORTED WIRE HARNESS OPENED WIRE HARNESS OVEN LAMP OR SOCKET WALL OUTLET MISADJUSTMENT SWITCH HOME FUSE OR BREAKER BLOCKED

Sharp R-580D NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL

WHILE THE OVEN IS IN OPERATION. CARRY OUT 3D CHECK. Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal. To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron filament terminals, the meter should show a reading of less

Room temperature .................. To = 21˚C

Initial temperature................. T1 = 11°C Temperature after (42 + 2) = 44 sec. ................................................................ T2 = 21°C Temperature difference Cold-Warm .............................................................. ∆T1 = 10°C Measured output power The equation is “P = 100 x ∆T” ........................................... P = 100 x 10°C = 1000 Watts

Sharp R-580D CARRY OUT 3D CHECKS.

Disconnect the leads from the monitor resistor. Using an ohmmeter and set on a low range. Check between the terminals of the monitor resistor. The resistance of monitor resistor is approx. 0.8 ohms. G MONITOR RESISTOR TEST TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST D HIGH VOLTAGE CAPACITOR TEST CARRY OUT 3D CHECKS. A. Isolate the high voltage capacitor from the circuit. B. Continuity check must be carried out with measu
CARRY OUT 3D CHECKS. Disconnect the leads from the motor. Using an ohmmeter, check the resistance between the two terminals as described in the table below. Table: Resistance of Motor Motors Resistance Fan motor Approximately 154 Ω Turntable motor Approximately 12 kΩ If incorrect readings are obtained, replace the motor. CARRY OUT 4R CHECKS H MOTOR WINDING TEST CARRY OUT 3D CHECKS. 1. If the fus

KEY UNIT TEST

If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the contacts are closed when the door is closed and open when the door is open. If the door sensing switch (stop switch) is good, disconnect the flat ribbon cable that connects the k

To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary

on the PWB, this foil pattern acts as a fuse. If the foil pattern is open, follow the troubleshooting guide given below for repair. Problem: POWER ON, indicator does not light up. CARRY OUT 3D CHECKS. STEPS OCCURRENCE CAUSE OR CORRECTION The rated AC voltage is not present between 1 Pin No. 1 of the 2-pin connector (A) and the Check supply vol

(8) If the sensor has not detected the vapour of the food, ERROR will appear and the oven will shut off.

Water load cooking test Make sure the oven has been plugged in at least five minutes before checking sensor cook operation. The cabinet should be installed and screws tightened. (1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup. (2) Place the container on the center of tray in the oven cavity. (3)

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL The touch control section consists of the following units. (1) Key Unit (2) Control Unit (The Control Unit consists of Power Unit and CPU Unit). The principal functions of these units and the signals communicated among them are explained below. Key Unit The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P10-P17. When a key pad is touched,

Sharp R-580D Signal coming from touch key.

When either G10 line on key matrix is touched, a corresponding signal out of P10 - P17 will be input into ANI0. When no key is touched, the signal is held at "H" level. 2 AN11 IN Signal similar to AN10. When either G9 line on key matrix is touched, a corresponding signal will be input into AN11. 3 AVSS IN Connected to VC. 4 P10 OUT Key strobe signal. Signal applied to touch-key section. A pulse signal is in

Sharp Microwave Oven Owners Instructions: