Ryobi CSB120 Operator's Manual

Text of Ryobi CSB120 Operator's Manual

7-1/4 in. (184 mm) Circular Saw

Model CSB120, CSB130, or CSB130JS DOUBLE INSULATED THANK YOU FOR BUYING A RYOBI CIRCULAR SAW. Your new circular saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator's manual before using your new saw

TABLE OF CONTENTS

I Product Specifications ......................................................................................................... 1 I Table Of Contents ............................................................................................................... 2 I General Safety Rules ....................................................................................................... 2-3 I Specific Safety Rules..............

GENERAL SAFETY RULES

Personal Safety (continued) I Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. I Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. I Use safety equipment. Always wear eye pro- tection. Dust mask, nonskid safety shoe

SPECIFIC SAFETY RULES

Specific Safety Rules for Circular Saws (continued) I Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released. I NEVER hold piece being cut in your hands or across your leg. It is important to support the wo

Additional Rules for Safe Operation

I Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or serious injury. I Always wear safety glasses. Everyday eye- glasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious per

KNOW YOUR CIRCULAR SAW

See Figure 1. Before attempting to use your saw, familiarize yourself with all operating features and safety requirements. WARNING: If any parts are missing, do not operate your tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. SWITCH Your saw is equipped with a pre-travel safety switch which reduces the possibility of accidental starting. When you depress the sw

I Carefully remove the saw and accessories from box.

Make sure all items listed in the Packing List are included. I Do not discard the packing material until you have carefully inspected and satisfactorily operated saw. I Examine all parts and accessories to make sure that no breakage has occurred during shipping. Any damaged part should be replaced before attempting to use the tool. CSB120 Circular Saw 7-1/4 Blade Wrench Warranty Card Oper

I Wipe a drop of oil onto inner blade washer and outer blade

washer ("D" washer) where they contact blade. WARNING: I Fit saw blade inside blade guard and onto spindle. NOTE: The saw teeth point upward at the front of the saw as shown in Figure 2. I Replace "D" washer and spring washer. NOTE: "Cupped" side of spring washer goes against "D" washer. See Figure 2. I Replace blade screw. Tighten blade screw securely. NOTE: Turn blade screw clo

CORRECT BLADE DEPTH SETTING =

BLADE EXPOSED 1/4 in. OR LESS ON UNDERSIDE OF WORKPIECE Fig. 6 WARNING: Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc., contained in this manual. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury. Save operator's manual, and review frequently for contin

DEPTH OF CUT ADJUSTMENT

Always keep correct blade depth setting. The correct blade depth setting for all cuts should not exceed 1/4 in. below the material to be cut. More blade depth will increase the chance of kickback and cause the cut to be rough. TO ADJUST BLADE DEPTH I Unplug your saw. WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. I Loosen depth adjustment knob. See Fig

NEVER PLACE YOUR SAW ON THAT PART OF THE

WORK THAT WILL FALL OFF WHEN THE CUT IS MADE. See Figure 12. Keep the cord away from cutting area. ALWAYS place the cord to prevent it from hanging up on the work while making a cut. Utilize the cord clip to help prevent cord problems. See Figure 13. DANGER: If the cord hangs up on the work during a cut, release the switch trigger immediately. Unplug your saw and reposition the cord to prevent it f

TO CROSS CUT OR RIP CUT

See Figure 15. When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base (as shown in Figure 15) and view the blade through the viewing window. Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut. NOTE: The distance from the line of

Ryobi CSB120 TO BEVEL CUT

See Figure 18 and 19. The angle of cut of your saw may be adjusted to any desired setting between zero and 51.5 degrees. There is a window in the saw base to help you line up the blade with the line of cut. See Figure 18. Align your line of cut with the inner blade guide notch on the saw base and view through the window when making full 45 degree bevel cuts. Since blade thicknesses vary and different angles re

LENGTH OF CUT SCALE

Fig. 20 BEVEL ADJUSTMENT KNOB ADJUSTMENT SCREW POSITIVE 0˚ BEVEL STOP HEX NUT COMBINATION SQUARE SAW BLADE Fig. 21 POSITIVE 0° BEVEL STOP See Figure 20. Your saw has a positive 0° bevel stop that has been factory adjusted to assure 0° angle of your saw blade, when making 90° cuts. However, misalignment can occur during shipping. TO CHECK: I Unplug your saw. WARNING: Failure to unplug your saw co

DUST NOZZLE (MODEL CSB 130JS)

See Figure 22. A dust nozzle is included with saw Model CSB130JS. As shown in figure 22, the dust nozzle fits over the dust chute which is located on the rear of the upper blade guard. Attach dust nozzle with a twisting motion. The easy rotation of the dust nozzle allows the operator to direct the flow of dust and chips. The dust and chip opening should always be turned away from the operator. TO POCKET CUT See Fi

Double insulation is a concept in safety in electric power

tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. IMPORTANT Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed

RYOBI CIRCULAR SAW – MODEL NUMBER CSB120

1 Page 18 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 23 22 24 12 21 26 10 27 34 25 28 33 32 31 30 26 27 29 10 35 36 36 37 37 38 39 41 40 42 35 10 10 10 10 10

Ryobi CSB120 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your

CIRCULAR SAW or when ordering repair parts. PARTS LIST Key Part No. Number Description Quan. Key Part No. Number Description Quan. 1 980648-001 Cord Tag..................................................... 1 2 976983-001 Data Plate ................................................... 1 3 976985-001 Logo Plate

Ryobi CSB120 RYOBI CIRCULAR SAW – MODEL NUMBERS CSB130 / CSB130JS

Page 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 28 27 15 26 17 29 42 30 34 32 33 31 35 36 33 32 37 38 39 40 41 15 43 15 15 44 44 45 45 46 15 47 48 49 43 15 50 16

Ryobi Saw Owners Instructions: