Wheelock TPA-100 Installation Instructions Manual
Text of Wheelock TPA-100 Installation Instructions Manual
273 Branchport Avenue
Long Branch, NJ 07740
(732) 222-6880
INSTALLATION INSTRUCTIONS
MODEL TPA-60/TPA-100
PAGING AMPLIFIERS
GENERAL APPLICATION INFORMATION
Wheelock's models TPA-60 and TPA-100 paging amplifiers are rated at 60 watts RMS and 100 watts RMS respectively.
These amplifiers afford a choice of five different inputs: two microphone inputs, one telephone input, and two background
music inputs. Only three of these inputs can be used actively at
SURFACE WALL MOUNTING
For surface mounting, be sure to use hardware suitable for the mounting surface.
FIGURE 2.
Power and Grounding
The 120 VAC line cord has a three-prong plug which should be plugged into a three wire grounded electric outlet. It is
very important to maintain the amplifier ground for safe and trouble-free operation. If there is no grounded electric outlet,
connect a wire from the GND terminal of the unit to a water or steam p
@ 1 KHz
60 WATTS RMS
100 WATTS RMS
2
TOTAL HARMONIC
DISTORTION
LESS THAN 2% THD
3
OUTPUTS
4 ohms, 8 ohms, 25V, 70V
4
TAPE/BOOSTER
OUTPUT
47K ohm, 0.6V
INPUTS
TELEPHONE
MIC 1/MIC 2
AUX 1/AUX 2
5
IMPEDANCE
600 ohm
150 ohm
47K ohms
6
SENSITIVITY
-20 dBm
.5 - 1 mV
220 mV
7
FREQ. RESPONSE
300Hz - 4KHz
70Hz - 15KHz
70Hz - 15KHz
8
SIGNAL TO NOISE
RATIO
60dB
60dB
70dB
9
TYPE OF INPUT
XFRMR
ISOLATED/BAL
B
TELEPHONE: Connect telephone wires to the input screw terminals marked TIP and RING. Set TEL/MIC 1 Switch to
TEL position. For connection to unused CO trunk port, see Figure 7. For connection to CO line, Centrex line or Analog
Station port, a Wheelock TPI-100 Interface is required.
MICROPHONE: Connect balanced low-impedance microphone wires to the input screw terminals marked LO-Z. The
shield must be connected to the GND screw terminals. A
The tape/booster output signal can also be used to feed an AUX input of another amplifier for system expansion or
greater power capabilities.
Note that the tape/booster output signal level is constant and unaffected by any of the amplifier controls.
OUTPUT CONNECTIONS
FIGURE 6.
CAUTION:
CONNECT ONLY TO PBX INCORPORATING ISOLATION FROM TELECOM NETWORK.
ATTENTION:
RACCORDER SUELEMENT A UNSYSTEME PBX INDEPENDANT/DU RESEAU DE
TELECOMMUNICATION.
Connect output
(Front panel controls, switches and indicators.)
NOTE:
ALL CONTROLS ROTATE CLOCKWISE TO INCREASE AND
COUNTERCLOCKWISE TO DECREASE.
POWER SWITCH (ILLUMINATED): The amber light inside the switch will light when the AC cord is plugged into a 120
VAC source and the power switch is pressed to the ON position.
MASTER VOLUME CONTROL: Sets the total output level of the amplifier without disturbing the individual level settings
of th
Wheelock TPA-100 MIC 2 CONTROL: Adjusts the volume of the MIC 2 paging input.
AUX 1/AUX 2 CONTROLS: Adjusts the volume of the AUX 1/AUX 2 inputs. Inputs are typically used for music,
prerecorded program sources, or tone signaling.
TONE CONTROLS: Set the individual Bass and Treble controls for optimum tonal balance of the output signal. The
amplifier frequency response is flat with the knob indicators pointing straight up (Dot #6).
MUSIC MUTE: Music is automatically m