Innovative 3500 Installation Instructions Manual

StudioLift™ for Apple Cinema Displays ® CinemaLift™ for Apple Cinema Displays ® 800.524.2744 www.LCDarms.com ...

TM 1. Hardware Parts List A. Arm ........................................................................................................................................... Page 2 B. FLEXmount™ ............................................................................................................................. Page 3 2. FLEXmount™ Set-up Options A. Desk Edge Clamp ................................................................................................................. Page 4 ...

Quantity 10-32 x 3/8" Phillips Flat Head Screw 705198 1 Dog Washer 105189 1 10-32 x 3/8” Phillips Flat Head Screw 702281 1 M2 Allen Wrench 702040 1 M2.5 Allen Wrench 702218 1 M3-16 Socket Head Screw 702038 3 M3 Steel Nut 702161 3 Cable Trough 702830 1 Forearm Cap 702825 1 Cable Clip DX1835 1 M3 Wrench DX2013 1 Endcap Bumper 702829 1 Hardware Parts List - Arm Page 2 (4-pack) ...

Page 3 Item Description & Part No. Quantity *Depending on the mount style you select, you will not use all of the parts listed below. Mount Column 702831 1 Base Plate 702826 1 Large “L” Bracket 702828 1 Small “L” Bracket 701116 1 3” x 3/4” x 1/4” Rectangular Spacer 701544 1 3/8-16 x 1 1/4” Flat Socket Cap Screw 701799 1 3/8-16 x 7/8” Button Socket Cap Screw 701122 1 3/8-16 Nylon Stop Nut 701418 1 3/8-16 x 7/8” Flat Socket Cap Screw 701124 1 3/8-16 x 2 1/2” Hex Head Bolt 700268 1 1/2-13 x 3” Socket Set Screw 701126 1 ...

Page 4 Desk Edge Clamp Mount Drop the nylon stop nut into the impression on the inside of the metal mount column. The rounded top of the nylon stop nut should be facing upwards. Step 1 Position the mount cup, base plate and the large “L” bracket so that the center holes are aligned as shown in the picture on the left. To screw the three parts together use the 3/8-16 x 1” flat head socket cap screw and the 7/32” allen wrench. Insert the 3/8-16 x 1” screw through the counter sunk hole in the large “L” bracket so that it engages the nylon stop nut. Tighten with the 7/32” allen wrench. The assembly is secure ...

Page 5 Through-Desk Mount Wall/Reverse Wall Mount Step 1 NOTE: The rounded part of the nut should be facing downward. Drill a hole 3/8” into desk or mounting surface bout 1 1/2”-2” in from the edge of the surface edge. Step 2 Remove the backing on the Neoprene foam pad and affix to the bottom of the mount cup. (ONLY if you will not be using the baseplate set-up in the next step) Step 3 Line up the mount cup over the hole and drop the 2.5” threaded bolt into the mount cup, through the optional base plate and through the desk. Without Baseplate With Baseplate Step 4 Under the desk, slide the rectangular spacer onto t ...

accommodate any challenging mounting surface. Special Mounting Scenarios Thick desk edge Desk with longer trim Desk without an edge Desk with a small lip FLEXmount™ Set-up Options Page 6 ...

TM Step 2 Attach the tilt mechanism to the adapter plate using four (4) #10-32 x 3/8” Flat Head Philips Pan screws. Step 1 Carefully remove the stand from the monitor by loosening the 3 screws using the M2 allen wrench. Slide the stand off of the monitor toward you. Loosen 3 Screws Slot Step 4 Attach the Apple bracket to the monitor using the (3) M3 x 16 Socket Head Screws. *You will need to press down on the bracket in order to line up the holes. (This is intended as it assures a snug fit for your monitor). Using the M3 wrench pro ...

cup. For the example the Through-Desk configuration was used. Step 1 Step 2 After securing the bracket to the flat panel monitor, insert the shaft of the tilt mechanism into the forearm. Fasten the 10-32 x 3/8" Philips Flat Head screw and washer into the hole in the bottom of the tilt mechanism to secure the monitor onto the arm. Step 3 Arm Assembly Page 8 ...

underneath the forearm, snap the cable clip into place. * Cable clip is for Apple Monitor cable only. Other cables may be hidden within the arm as shown in Step 2. Be sure to leave enough slack for cables to loop around the elbow of the arm. Included with your kit is a USB extension plug. Connect the end of the USB extension into the end of the USB coming out of the keyboard. Feed the cord through the arm as above step indicates. Step 2 The remaining cables can be hidden within the arm by following the steps and diagrams below. Feed the cables through the endcap (elbow), up through the o ...

locate the set screw under the tilter. To tighten friction, lightly turn the wrench to the right (clockwise). To loosen, lightly turn the wrench to the left (counter-clockwise). When your monitor moves with ease, stays tilted in the up or down position, the friction is set. Adjusting Counter-balance *The monitor MUST be attached before adjusting the counter-balance. *It is important to hold the arm in a horizontal position before beginning. Use the 7/32” allen wrench and insert into the top of the end cap. Turn left (counter-clockwise) to strengthen. Turn right (cloc ...

holding double monitors or for pivoting LCD’s, keyboard arms and wall mounts. Wall Mounts Keyboard Mounting Stands Innovative Office Products, Inc. | 100 Kuebler Road | Easton, PA 18040 www.LCDarms.com | [email protected] ...