Precor M9.25i Owner's Manual

Text of Precor M9.25i Owner's Manual

Treadmill with the

Cardiologic TM System featuring Smart Rate ® R

When using an electrical appliance, basic precautions should always be taken, including the

following: • Read all instructions before using the M9.25i. These instructions are written to ensure your safety and to protect the unit. Before beginning any fitness program, you should obtain a complete physical examination by your physician. Il est conseillé de subir un examen médical complet avant d’entreprendre tout programme d’exercise. Si vous

Assemble and operate the treadmill on a solid, level surface. Locate the treadmill at least 4

feet from walls or furniture. Keep the area behind the treadmill clear. • Check the M9.25i before each use. Completely assemble the treadmill before using it. • Turn OFF (O) and unplug the treadmill when adjusting or working near the rear roller. Do not adjust the running belt when someone is standing on the unit. • Keep all electr

Keep the equipment dry. Although the chest strap should not be immersed in water, wetting the

electrodes and your chest will improve the initial performance. Note that perspiration on the chest strap during workouts is normal and actually enhances the signal being sent from the chest strap’s transmitter. • To conduct the electrical impulses from your heart, the chest strap’s electrodes require a certain percentage of salts and minerals in

Precor M9.25i Canadian Department of Communications

“This digital apparatus does not exceed the (Class B) limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.” “Le présent appareil numérique n’émet pas de bruits radioéélectriques dépassant les limites applicables aux appareils numériques (de la class B) prescrites dans le Règlement sur le brouillage radi

Table of Contents

Before You Begin ............................................................ 7 Unpacking the Treadmill ................................................................. 7 Setting Up the Low Impact Treadmill ............................ 9 Installation Requirements ............................................................... 9 Assembly Instructions ..................................................................... 9 Checking

Precor M9.25i Before You Begin

1 This manual explains how to assemble, use, and maintain the M9.25i Low Impact Treadmill. The following conventions are used in this manual: “Note:” Contains additional information that applies to the preceding text. “Important:” Indicates information to which you should pay special attention. “CAUTION:” Indicates steps or information necessary to prevent harm to yourself or damage to the equipment. “WARNING:” Provi

After unpacking the treadmill, open the hardware kit (refer to Diagram 1) and make sure that you

have the following items: (A) four frame-to-base plate bolts (B) two water bottle cage mounting bolts (C) two lower handrail clamp bolts (D) four split star washers—place on frame-to-base bolts (E) four internal star washers—2 for lower handrail clamps/2 for mounting water bottle cage (F) one 5/16" hex key—frame-to-base bolts (G) one 1/4" hex key�

Setting Up the Low Impact Treadmill

2 CAUTION: Do not remove or otherwise bypass the 3-prong plug with an adapter or extension cord in order to use a non-grounded outlet. Electrical damage can occur if the treadmill is connected to an improper power source. You do not need any special knowledge or experience to set up a M9.25i treadmill. However, you must review and follow the instructions in this manual. If you do not assemble and use the treadmil

Remove the treadmill’s hood using a phillips head screwdriver. Unscrew all six screws

and set them aside. See Diagram 2. Grasp both sides of the hood with your hands and pull up to remove the hood from the base. Diagram 2 Hood Screw Base Remove the hood. Wheel PRECOR PRECOR Diagram 3 Upright column support Lower board Front plate Ribbon cable connector Lower board’s cables Proper tab alignment on receptacle Plug connector into lower board. 3

Secure the upright column support to the base by lifting it into position onto the base

mounting plate. See Diagram 4. Align the bolt holes and hold onto the upright column support as you insert the frame-to-base bolts and finger tighten. Alternately tighten each bolt using the 5/16" hex key (F) provided. 7. With the upright column support secure, replace the hood by aligning the screw holes on the hood with the holes in the base frame. Tighten

10. To mount the lower portion of the handrails, take the lower handrail clamps (J), two of the

internal star washers (E), and lower handrail clamp bolts (C) out of the hardware kit. Refer to Diagram 6 while taking the following steps: Note: Perform these steps on one side of the treadmill before proceeding to the other side. a. Put one internal star washer (E) on each of the lower handrail clamp bolts (C). Place the bolts on either side of the tre

11. Return to the upper handrail clamp, check to see that the foam on the handrails touches the

edge of the clamp, readjust the handrails if necessary, and tighten the bolts securely using the 3/16" hex key (H) provided. 12. Install the water bottle cage by placing one internal star washer (E) on each of the mounting bolts (B). Position the cage onto the mounting hole locations and insert the bolts. See Diagram 8. Securely tighten the bolts using t

CAUTION: Do not walk on the running belt

during this procedure. Checking the Alignment of the Running Belt The belt is aligned at the factory before shipment. However, during shipment or by using the treadmill on an uneven surface, the belt might move off center. Proper belt alignment is important because it allows the belt to remain centered and assures smooth operation. Take the following steps to check the alignment: 1. Insert the magnetic safe

S A F E T Y K E Y B E L O W

3 As simple as using the M9.25i Low Impact Treadmill might seem, you should read this section so that you can use the treadmill safely and effectively. This section of the owner’s manual provides the basic information you need for exercising on your treadmill, including the following: • locating the ON and OFF switch • using the magnetic safety key • reviewing features on the electronic console • changing the

Removing the safety key does not turn OFF the treadmill. If the safety key becomes dislodged from

inside its compartment, the running belt and any incline movement stops and a message “RESET SAFETY SWITCH” scrolls across the display until the safety key is replaced. Replacing the safety key causes the treadmill to return to its place or position prior to the interruption. However, if the treadmill was moving between inclines when the safety key

Precor M9.25i User I.D: One of four user I.D.’s can appear on the display. Choosing a user I.D. enables the

treadmill to identify you and track your cumulative workout statistics. It stores information about your weight, preferred program, cumulative workout statistics, fitness score, perceived level of fitness, and track record. If other people use the treadmill, each person (up to four people) can have their own user I.D. number and personalized workout sess

Precor Treadmill Owners Instructions: