Crown Micro-Tech 2400 Service Manual

Text of Crown Micro-Tech 2400 Service Manual

Micro-Tech 2400 Amplifier Service Manual

1 MICRO-TECH ®-2400 POWER AMPLIFIER SERVICE MANUAL K-SVCMT24 7-95 Micro-Tech®, ODEP® and Crown® are registered trademarks of Crown International, Inc. Mailing Address: P.O. Box 1000 Elkhart, IN U.S.A. 46515-1000 Shipping Address: 57620 C.R. 105 Elkhart, IN U.S.A. 46517 ©1995 by CROWN INTERNATIONAL, INC.
Micro-Tech 2400 Amplifier Service Manual 2 À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ PAS LES COUVERTURES. RIEN DES PARTIES UTILES À L’INTÉRIEUR. DÉBRANCHER LA BORNE AVANT D’OUVRIR LA MODULE EN ARRIÈRE. TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DISCONNECT POWER CORD BEFORE REMOVING REAR INPUT MODULE TO ACCESS GAIN SWITCH. CAUTION AVIS WARNING
Micro-Tech 2400 Amplifier Service Manual 3 Introduction ............................................................. 4 Scope ...................................................................... 4 Warranty .................................................................. 4 Parts Information ..................................................... 5 Specifications .......................................................... 6 Voltage Conversion ..............
Micro-Tech 2400 Amplifier Service Manual 4 Crown Technical Support Group Factory Service Parts Department Mailing Address: PO Box 1000 Elkhart, IN USA 46515-1000 Shipping Address: 57620 C.R. 105 Elkhart, IN USA 46517 Phone: (219) 294-8200 Toll Free: (800) 342-6939 FAX: (219) 294-8301 This manual contains service information on Crown power amplifiers. It is designed to be used in conjunc- tion with the applicable Owner's Manual. However, some importan
Micro-Tech 2400 Amplifier Service Manual 5 Parts Information shipment on a C.O.D. or pre-payment (check or credit card) basis. TERMS Normal terms are pre-paid. Net-30 Days applies to only those firms having pre-established accounts with Crown. If pre-paying, the order must be packed and weighed before a total bill can be established, after which an amount due will be issued and shipment made upon receipt of pre-payment. New parts re- turned for credit are
Micro-Tech 2400 Amplifier Service Manual 6 Specifications Unless noted otherwise, all specifications are based on driving an 8 ohm load per channel, both channels driven, the sensitivity switch in the 26dB position, the AC supply is 120VAC at 60Hz. Crown specifications are guaranteed through the warranty period (normally 3 years). Because our testing methods are more strin- gent than our published specifications, every Crown amplifier will exceed its publi
Micro-Tech 2400 Amplifier Service Manual 7 Voltage Conversion The 120 Volt 60 Hz version, sold in the United States, is not voltage selectable. It does not have a voltage selection board. This version is to be used only with 120 Volts and only with 60Hz. All other versions of the Micro Tech 2400 use a volt- age selection board. The following chart indicates different configurations of jumpers for different volt- ages. Note that the circuit breakers, fuse a
Micro-Tech 2400 Amplifier Service Manual 8 Theory OVERVIEW It should be noted that over time Crown makes im- provements and changes to their products for various reasons. This manual is up to date as of the time of writing. For additional information regarding these amplifiers, refer to the applicable Technical Notes provided by Crown for this product. This section of the manual explains the general opera- tion of a typical Crown power amplifier. Topics co
Micro-Tech 2400 Amplifier Service Manual 9 Theory amplifies the difference between input and output signals, any difference in the two waveforms will produce a near open loop gain condition which in turn results in high peak output voltage. The output of the Error Amp, called the Error Signal (ES) drives the Voltage Translators. VOLTAGE AMPLIFICATION The Voltage Translator stage separates the output of the Error Amp into balanced positive and negative driv
Micro-Tech 2400 Amplifier Service Manual 10 High Side (HS) The High Side (HS) of the bridge operates much like a conventional bipolar push-pull output configuration. As the input drive voltage becomes more positive, the HS NPN conducts and delivers positive voltage to the load. Eventually the NPN devices reach full conduc- tion and +Vcc is across the load. At this time the HS PNP is biased off. When the drive signal is negative going, the HS PNP conducts t
Micro-Tech 2400 Amplifier Service Manual 11 respect to each other. This allows the power supply to deliver +Vcc and -Vcc from the same bridge rectifier and filter as a total difference in potential, regardless of their voltages with respect to ground. The LS uses inverted feedback from the HS output to control the ground reference for the rails (±Vcc). Both LS quad- rants are arranged in a three-deep Darlington and are biased AB+B in the same manner as th
Micro-Tech 2400 Amplifier Service Manual 12 Theory NEGATIVE LOW SIDE OUTPUT PNP STAGE POSITIVE LOW SIDE OUTPUT NPN STAGE NEGATIVE HIGH SIDE OUTPUT PNP STAGE POSITIVE HIGH SIDE OUTPUT NPN STAGE HIGH SIDE BIAS SERVO +LVA -1 -LVA -1 +VOLTAGE TRANSLATOR -VOLTAGE TRANSLATOR OUTPUT DEVICE EMULATION PROTECTION ERROR AMP VGS BGS BALANCED INPUTS INVERTING BRIDGE BALANCE LOW SIDE BIAS DIODE STRING -1 -1 MAIN NEGATIVE FEEDBACK (NFb) LOOP Figure 3. Typical Crown Ampli
Micro-Tech 2400 Amplifier Service Manual 13 Electrical Checkout Procedures GENERAL INFORMATION The following test procedures are to be used to verify operation of this amplifier. DO NOT connect a load or inject a signal unless directed to do so by the proce- dure. These tests, though meant for verification and alignment of the amplifier, may also be very helpful in troubleshooting. For best results, tests should be performed in order. All tests assume that
Micro-Tech 2400 Amplifier Service Manual 14 TEST 6: VOLTAGE GAIN Spec 26dB Gain: Gain of 20.0 ±3%. Spec 0.775V Sensitivity: ±6%. Spec 1.4V Sensitivity: +12%/–6%. Initial Conditions: Controls per standard. Procedure: No load connected. Inject a 0.775 VAC 1 kHz sine wave with the Sensitivity Switch in the 26 dB position. Measure 15.5 VAC ±0.5 VAC at the amplifier output. Inject a 0.775 VAC 1 kHz sine wave with the Sensitivity Switch in the 0.775V positi
Micro-Tech 2400 Amplifier Service Manual 15 Electrical Checkout Procedures Procedure Short: Inject a 60 Hz sine wave at 5 VAC minimum output. After establishing signal, short the output for 10 seconds. TEST 14: ODEP LIMITING Spec: No oscillation on ODEP Limiting wave form; either channel controls limiting in Parallel Mono Mode. Initial Conditions: Controls per standard; rag or other obstruction blocking fan so that it does not turn. Procedure: Load the amp
Micro-Tech 2400 Amplifier Service Manual 16 Parts List (Non-Module) SUPPLIMENTAL ITEMS CPN ITEM QTY D 4137-2 Nylon Thumbscrew Washer 4 C 3342-0 Feet, Black Self-Stick 4 A10087-71012 10-32 .75 Machine (Rack Screw) 4 K80603-2 MT Series Owners Manual 1 POWER SUPPLY CPN ITEM QTY D 7975-2 Power Cord (US Models) 1 A10793-0503G Power Cord (European plug) 1 D 8633-6 Power Transformer (120V 60 Hz only) 2 D 8631-0 Power Transformer (Universal Volt) 2 C 9508-0 Circui
Micro-Tech 2400 Amplifier Service Manual 17 Parts List (Non-Module) OUTPUT ASSEMBLY CONT. (ONE PER CHANNEL) CPN ITEM QTY(PER CHANNEL) D 7665-9 Clip, TO-3P Mounting 2 D 7666-7 Bracket, TO-3P Heatsink 2 C 8813-5 Q318/Q418 Bias Servo MPSA18/MPS8097 1 B 5842-8 Tubing, #23 TFE Thin Wall Red (For C 8813-5) Request in Inches C 5826-0 S100/S200 Thermal Sense LM334Z 1 B 5464-1 Tubing, #24 Teflon Thin Wall (For C 5826-0) Request in Inches D 8774-8 PTC Thermal Sensor
Micro-Tech 2400 Amplifier Service Manual 18 Parts List (Non-Module) MAIN CHASSIS ASSEMBLY CPN ITEM QTY D 8501-5 Cover, Top 1 D 8548-6 Cover, Bottom 1 A10110-70605 Screw, 6-32-.312 Taptite Ph (Covers) 16 M21447J3 Main Chassis 1 MISCELLANEOUS CPN ITEM QTY A10110-70812 8-32 x .750 Taptite Pnhd Screw 2 A10094-3 Washer, #6 Black Star 3 A10109-10822 Screw, 8-18-1.375 Pan Ph 2 A10192-1 Snap Bushing .5 4 C 6912-7 Tension Retainer Board Support 2 C 6913-5 Spacer Nu
Micro-Tech 2400 Amplifier Service Manual 19 Module Information MODULE HISTORY The Micro Tech 2400 amplifier was introduced in January of 1995. Since then there have been several updates and revisions, some of which called for new modules. The following is a list of all modules used up to this date, July 1995. OUTPUT MODULES: (left and right are identical) Q43354-2 Original Output Module, still in production. Uses P10429-2 board. MAIN MODULES: Q43328-6 Orig

Crown Amplifier Owners Instructions: