Prolight ELUM120A Operation & User’s Manual

Text of the manual

Tour Batten TW User Manual

2 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! •� Before�your�initial�start-up,�please�make�sure�that�there�is�no�damage�caused�during�transportation. •� Should�there�be�any�damage,�consult�your�dealer�and�do�not�use�the�equipment. •� To�maintain�the�equipment�in�good�working�condition�and�to�ensure�safe�operation,�it�is�necessary�� for�the�user�to�follow�the�safety�instructions�and�warning�notes�written�in�this�manual. •� Please�note�that�damages�caused�by�user�modifications�to�this�equipment�are�not�subject�to�warranty. IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment. OPERATING DETERMINATIONS If�this�equipment�is�operated�in�any�other�way,�than�those�described�in�this�manual,�the�product�may�suffer�damage�and�� the�warranty�becomes�void.�Incorrect�operation�may�lead�to�danger�e.g:�short-circuit,�burns�and�electric�shocks�etc.� Do�not�endanger�your�own�safety�and�the�safety�of�others!� Incorrect�installation�or�use�can�cause�serious�damage�to�people�and/or�property. CAUTION! KEEP THIS EQUIPMENT AWAY FROM RAIN, MOISTURE AND LIQUIDS CAUTION! TAKE CARE USING THIS EQUIPMENT! HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!! •� Never�let�the�power�cable�come�into�contact�with�other� cables.�Handle�the�power�cable�and�all�mains�voltage�� connections�with�particular�caution! •� Never�remove�warning�or�informative�labels�from�the�unit. •� Do�not�open�the�equipment�and�do�not�modify�the�unit. •� Do�not�connect�this�equipment�to�a�dimmer�pack. •� Do�not�switch�the�equipment�on�and�off�in�short�intervals,� as�this�will�reduce�the�system’s�life. •� Only�use�the�equipment�indoors. •� Do�not�expose�to�flammable�sources,�liquids�or�gases. •� Always�disconnect�the�power�from�the�mains�when�� equipment�is�not�in�use�or�before�cleaning!�Only�handle� the�power-cable�by�the�plug.�Never�pull�out�the�plug�by� pulling�the�power-cable. •� Make�sure�that�the�available�mains�supply�voltage�is� between�100~240V�AC,�50/60Hz. •� Make�sure�that�the�power�cable�is�never�crimped�or�� damaged.�Check�the�equipment�and�the�power�cable� periodically. •� If�the�equipment�is�dropped�or�damaged,�disconnect�the� mains�power�supply�immediately�and�have�a�qualified� engineer�inspect�the�equipment�before�operating�again.� � •� If�the�equipment�has�been�exposed�to�drastic�� temperature�fluctuation�(e.g.�after�transportation),�� do�not�connect�power�or�switch�it�on�immediately.�� The�arising�condensation�might�damage�the�equipment.� Leave�the�equipment�switched�off�until�it�has�reached� room�temperature. •� If�your�product�fails�to�function�correctly,�stop�use� immediately.�Pack�the�unit�securely�(preferably�in�the�� original�packing�material),�and�return�it�to�your�Pro�Light� dealer�for�service. •� Only�use�fuses�of�same�type�and�rating. •� Repairs,�servicing�and�power�connection�must�only�be�� carried�out�by�a�qualified�technician.�THIS�UNIT�CONTAINS� NO�USER�SERVICEABLE�PARTS. •� This�lighting�fixture�is�for�professional�use�only�-�it�is� not�designed�for�or�suitable�for�household�use.�The� product�must�be�installed�by�a�qualified�technician�in� accordance�with�local�territory�regulations.�The�safety�of� the�installation�is�the�responsibility�of�the�installer.�The� fixture�presents�risks�of�severe�injury�or�death�due�to�fire� hazards,�electric�shock�and�falls. •� Warning!�Risk�Group�2�LED�product�according�to� EN�62471.�Do�not�view�the�light�output�with�optical� instruments�or�any�device�that�may�concentrate�the�beam. •� WARRANTY:�Two�years�from�date�of�purchase.

Tour Batten TW User Manual

3 Product overview & technical specifications This�Tour�Batten�TW�features�10�x�10W�warm�white�LEDs�and�a�variable�colour�temperature�between� 1600K–2900K.�The�temperature�can�be�set�via�the�rear�menu�or�DMX.�When�dimmed,�the�fixture�can�emulate�a� traditional�halogen�lamp�with�an�orange�glow�similar�to�a�sun�strip,�whilst�the�18°�beam�produces�a�smooth�wash� or�blinder�effect. Tour Batten TW Specifications Tour Batten TW Power�consumption 110W Power�supply 100~240V,�50/60Hz Dimensions 139�x�1082�x�130mm Weight 6.5kg Order�code ELUM120A 1082mm 130mm 1000mm 78.2mm 1042mm 139mm 92.8mm 01�-�Power�indicator�LED 02�-�RDM/DMX�indicator�LED 03�-�LCD�display 04�-�Function�buttons 05�-�5-Pin�DMX�input 06�-�5-Pin�DMX�output 07�-�PowerCON�input 08�-�PowerCON�output 09�-�Fuse�T3.15A�250V 10�-�Power�switch�on/off In�the�box:�1 x fixture, 2 x end brackets, 1 x power cable & 1 x user manual RDM/DMX OUTPUT POWER OUTPUT (15A Max.) RDM/DMX INPUT POWER INPUT (15A Max.) 100-240V~50/60Hz MENU UP ENTER RDM/DMX POWER DOWN PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC POWER FUSE: T3.15A 250V TOUR BATTEN TW www.prolight.co.uk CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS FIXTURE WARNING: THIS PRODUCT MUST BE EARTHED RDM/DMX OUTPUT POWER OUTPUT (15A Max.) MENU UP ENTER RDM/DMX POWER DOWN PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC TOUR BATTEN TW www.prolight.co.uk CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS FIXTURE WARNING: THIS PRODUCT MUST BE RDM/DMX OUTPUT POWER OUTPUT (15A Max.) MENU UP ENTER RDM/DMX POWER DOWN PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC TOUR BATTEN TW www.prolight.co.uk CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS FIXTURE WARNING: THIS PRODUCT MUST BE EARTHED RDM/DMX INPUT POWER INPUT (15A Max.) 100-240V~50/60Hz ENTER RDM/DMX POWER WN NTER” TO UNLOCK 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC POWER FUSE: T3.15A 250V TOUR BATTEN TW www.prolight.co.uk CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS FIXTURE WARNING: THIS PRODUCT MUST BE EARTHED RDM/DMX INPUT POWER INPUT (15A Max.) 100-240V~50/60Hz 1 = Ground 2 = Data - 3 = Data + 4 = NC 5 = NC POWER FUSE: T3.15A 250V TOUR BATTEN TW www.prolight.co.uk CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS FIXTURE WARNING: THIS PRODUCT MUST BE EARTHED 06 05 08 01 02 04 03 07 09 10 0m 1m 2m 3m 4m 5m 18° - Lux 2140 1731 769 20° 433 277 •�2�year�warranty •�10�x�10W�warm�white�LEDs •�Beam�angle:�18° •�1731�Lux�@�2m •�Pixel�mapping�capabilities •�DMX�channels:�8�bit�-� 1/2/5/10/6 •�16�bit�-�2/4/10/20 •�Static,�auto�run�and�master/ slave�modes •�0�-�100%�16�bit�dimming •�RDM�(Remote�Device� Management) •�4�push�button�menu�with� LCD�display •�PowerCON�input/output •�5-Pin�XLR�input/output •�Convection�cooled

Tour Batten TW User Manual

4 Operating instructions Main Menu Sub Menu Options/Values Description DMX� Channel 01/8Bit 1�channel�mode�-�8�bit DMX�Channel�Setting 02/16Bit 2�channel�mode�-�16�bit 02/8Bit 2�channel�mode�-�8�bit 04/16Bit 4�channel�mode�-�16�bit 05/8Bit 5�channel�mode�-�8�bit 10/16Bit 10�channel�mode�-�16�bit 10/8Bit 10�channel�mode�-�8�bit 20/16Bit 20�channel�mode�-�16�bit 06/8Bit 6�channel�mode�-�8�bit Address 001-512 DMX�Address�Setting No�DMX OFF Functions�when�no�DMX�signal Hold Program Glide ON Switching�DMX�fade�to�on�activates� a�short�delay�on�DMX�commands OFF Chase Program Program:01-Program:16/� Program:�Auto/�Program:�Full Program Master 000-100 Master�dimmer Speed 01-100 Program�Speed FadeTime 000-100 Program�Fade IMPORTANT! PLEASE NOTE: The�LCD�display�for�this�fixture�has�a�menu�locking�function�where�� after�30�seconds�of inactivity�it�will�lock.�To�unlock�the�menu�hold�the�“MENU”�and�“ENTER” buttons� for�3�seconds.

Tour Batten TW User Manual

5 DMX mode: Operating�in�a�DMX�control�mode�environment�gives�the�user�the�greatest�flexibility�when�it�comes�� to�customising�or�creating�a�show.�In�this�mode�you�will�be�able�to�control�each�individual�trait�of�the� fixture�and�each�fixture�independently.� To�access�the�DMX�channel�mode,�press�the�“MENU”�button�on�the�front�of�the�unit�to�show�� “Address” on�the�LCD�display.�Press�the�“ENTER”�button�to�show�“Channel” on�the�LCD�display.�� Now�use�the�“UP”�and�“DOWN”�buttons�to�choose�one�of�the�channel�modes;�� 1/2/5/10/6�-�8�bit,�2/4/10/20�-�16�bit�(see�chart�on�page�4).� Press�the�“ENTER”�button�to�confirm�the�setting. To�access�the�DMX�address�mode,�press�the�“MENU”�button�on�the�front�of�the�unit�to�show�� “Address” on�the�LCD�display.�Now�the�“UP”�and�“DOWN”�buttons�to�set�the�required�DMX�address.�� Press�the�“ENTER”�button�to�confirm�the�setting. To�access�the�DMX�bit�setting,�press�the�“MENU”�button�on�the�front�of�the�unit�to�show�� “Address” on�the�LCD�display.�Press�the�“ENTER”�button�to�show�“Glide” on�the�� LCD�display.�Now�the�“UP”�and�“DOWN”�buttons�to�set�the�DMX�fade�“ON”�or�“OFF”.�� Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. Operating instructions Channel Value Function 1 000-255 LEDs�1-10�dimmer�(0-100%) 1 channel mode - 8 bit: Channel Value Function 1 000-255 LEDs�1-5�dimmer�(0-100%) 2 000-255 LEDs�6-10�dimmer�(0-100%) 2 channel mode - 8 bit: Channel Value Function 1 000-255 LEDs�1-2�dimmer�(0-100%) 2 000-255 LEDs�3-4�dimmer�(0-100%) 3 000-255 LEDs�5-6�dimmer�(0-100%) 4 000-255 LEDs�7-8�dimmer�(0-100%) 5 000-255 LEDs�9-10�dimmer�(0-100%) 5 channel mode - 8 bit: Channel Value Function 1�high�8�byte� 2�low�8�byte 00000- 65535 LEDs�1-10�dimmer�� (0-100%) 2 channel mode - 16 bit: Channel Value Function 1�high�8�byte� 2�low�8�byte 00000- 65535 LEDs�1-5�dimmer�� (0-100%) 3�high�8�byte� 4�low�8�byte 00000- 65535 LEDs�6-10�dimmer�� (0-100%) 4 channel mode - 16 bit: Channel Value Function 1�high�8�byte� 2�low�8�byte 00000- 65535 LEDs�1-2�dimmer�� (0-100%) 3�high�8�byte� 4�low�8�byte 00000- 65535 LEDs�3-4�dimmer�� (0-100%) 5�high�8�byte� 6�low�8�byte 00000- 65535 LEDs�5-6�dimmer�� (0-100%) 7�high�8�byte� 8�low�8�byte 00000- 65535 LEDs�7-8�dimmer�� (0-100%) 9�high�8�byte� 10�low�8�byte 00000- 65535 LEDs�9-10�dimmer�� (0-100%) 10 channel mode - 16 bit:

Tour Batten TW User Manual

6 Operating instructions Channel Value Function 1�high�8�byte� 2�low�8�byte 00000- 65535 LED�1�dimmer�(0-100%) 3�high�8�byte� 4�low�8�byte 00000- 65535 LED�2�dimmer�(0-100%) 5�high�8�byte� 6�low�8�byte 00000- 65535 LED�3�dimmer�(0-100%) 7�high�8�byte� 8�low�8�byte 00000- 65535 LED�4�dimmer�(0-100%) 9�high�8�byte� 10�low�8�byte 00000- 65535 LED�5�dimmer�(0-100%) 11�high�8�byte� 12�low�8�byte 00000- 65535 LED�6�dimmer�(0-100%) 13�high�8�byte� 14�low�8�byte 00000- 65535 LED�7�dimmer�(0-100%) 15�high�8�byte� 16�low�8�byte 00000- 65535 LED�8�dimmer�(0-100%) 17�high�8�byte� 18�low�8�byte 00000- 65535 LED�9�dimmer�(0-100%) 19�high�8�byte� 20�low�8�byte 00000- 65535 LED�10�dimmer�(0-100%) 20 channel mode - 16 bit: Channel Value Function 1 000-255 LED�1�dimmer�(0-100%) 2 000-255 LED�2�dimmer�(0-100%) 3 000-255 LED�3�dimmer�(0-100%) 4 000-255 LED�4�dimmer�(0-100%) 5 000-255 LED�5�dimmer�(0-100%) 6 000-255 LED�6�dimmer�(0-100%) 7 000-255 LED�7�dimmer�(0-100%) 8 000-255 LED�8�dimmer�(0-100%) 9 000-255 LED�9�dimmer�(0-100%) 10 000-255 LED�10�dimmer�(0-100%) 10 channel mode - 8 bit: Channel Value Function 1 000-255 Master�dimmer�(0-100%) 2 000-255 Program 3 000-255 Program�speed�(slow-fast) 4 000-255 Fade�Time�(slow-fast) 5 000-080 Program�Stop 081-160 Program�Pause 161-255 Program�Play 6 000-255 Master 6 channel mode - 8 bit:

Tour Batten TW User Manual

7 Chase mode: To�access�the�chase�mode,�press�the�“MENU”�button�on�the�front�of�the�unit�to�show�� “Program” on�the�LCD�display.�Now�the�“UP”�and�“DOWN”�buttons�to�set�the�required�program�“01” - “10”/ “Auto”/ “Full”.�Press�the�“ENTER”�button�to�confirm�the�setting. “Master” should�now�be�shown�on�the�LCD�display.�Use�the�“UP”�and�“DOWN”�buttons�to�set�the�chase� modes�dimming�“000” - “100”.�Press�the�“ENTER”�button�to�confirm�the�setting.� (000 = LED off, 100 = LED at full brightness). “Speed” should�now�be�shown�on�the�LCD�display.�Use�the�“UP”�and�“DOWN”�buttons�to�set�the�required� speed�“01” - “100”.�Press�the�“ENTER”�button�to�confirm�the�setting.� (01 = slow, 100 = fast). “FadeTime” should�now�be�shown�on�the�LCD�display.�Use�the�“UP”�and�“DOWN”�buttons�to�set�the� required�amount�of�fade�“000” - “100”.�Press�the�“ENTER”�button�to�confirm�the�setting.� (000 = no fade, 100 = full fade). To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. Operating instructions

Tour Batten TW User Manual

8 Setting the DMX address: The�DMX�mode�enables�the�use�of�a�universal�DMX�controller.�Each�fixture�requires�a�“start�address”� from�1-�511.�A�fixture�requiring�one�or�more�channels�for�control�begins�to�read�the�data�on�the�channel� indicated�by�the�start�address.�For�example,�a�fixture�that�occupies�or�uses�7�channels�of�DMX�and�was� addressed�to�start�on�DMX�channel�100,�would�read�data�from�channels:�100,101,102,103,104,105� and�106.�Choose�a�start�address�so�that�the�channels�used�do�not�overlap.�E.g.�the�next�unit�in�the� chain�starts�at�107. DMX 512: DMX�(Digital�Multiplex)�is�a�universal�protocol�used�as�a�form�of�communication�between�intelligent� fixtures�and�controllers.�A�DMX�controller�sends�DMX�data�instructions�form�the�controller�to�the�fixture.� DMX�data�is�sent�as�serial�data�that�travels�from�fixture�to�fixture�via�the�DATA�“IN”�and�DATA�“OUT”�� XLR�terminals�located�on�all�DMX�fixtures�(most�controllers�only�have�a�data�“out”�terminal). DMX linking: DMX�is�a�language�allowing�all�makes�and�models�of�different�manufactures�to�be�linked�together�� and�operate�from�a�single�controller,�as�long�as�all�fixtures�and�the�controller�are�DMX�compliant.�� To�ensure�proper�DMX�data�transmission,�when�using�several�DMX�fixtures�try�to�use�the�shortest�� cable�path�possible.�The�order�in�which�fixtures�are�connected�in�a�DMX�line�does�not�influence�the�� DMX�addressing.�For�example;�a�fixture�assigned�to�a�DMX�address�of�1�may�be�placed�anywhere�in�� a�DMX�line,�at�the�beginning,�at�the�end,�or�anywhere�in�the�middle.�When�a�fixture�is�assigned�a�� DMX�address�of�1,�the�DMX�controller�knows�to�send�DATA�assigned�to�address�1�to�that�unit,�� no�matter�where�it�is�located�in�the�DMX�chain. DATA cable (DMX cable) requirements (for DMX operation): This�fixture�can�be�controlled�via�DMX-512�protocol.�The�DMX�address�is�set�on�the�back�of�the�unit.� Your�unit�and�your�DMX�controller�require�a�standard�3-pin�XLR�connector�for�data�input/output,�� see�image�below. Note: DMX cable must be daisy chained and cannot be split. DMX setup Further�DMX�cables�can�be� purchased�from�all�good�sound� and�lighting�suppliers�or�� Pro�Light�Concepts�dealers. Please�quote: CABL185 – 2m CABL187 – 5m CABL188 – 10m

Tour Batten TW User Manual

9 Notice: Be�sure�to�follow�the�diagrams�below�when�making�your�own�cables.�Do�not�connect�the�cables�� shield�conductor�to�the�ground�lug�or�allow�the�shield�conductor�to�come�in�contact�with�the�XLRs�� outer�casing.�Grounding�the�shield�could�cause�a�short�circuit�and�erratic�behaviour. Special note: Line termination: When�longer�runs�of�cable�are�used,�� you�may�need�to�use�a�terminator�on�� the�last�unit�to�avoid�erratic�behaviour. Using a cable terminator will decrease the possibilities of erratic behaviour. (3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89) 5-pin XLR DMX connectors: Some�manufactures�use�5-pin�XLR�connectors�for�data�transmission�in�place�of�3-pin.�5-pin�XLR�fixtures� may�be�implemented�in�a�3-pin�XLR�DMX�line.�When�inserting�standard�5-pin�XLR�connectors�in�to�a� 3-pin�line�a�cable�adaptor�must�be�used.�The�diagram�below�details�the�correct�cable�conversion. Termination�reduces�signal�transmission� problems�and�interference.�It�is�always� advisable�to�connect�a�DMX�terminal,� (resistance�120�Ohm�1/4�W)�between�pin�2� (DMX-)�and�pin�3�(DMX+)�of�the�last�fixture. 5-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C 3-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 3-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 5-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C DMX setup

Tour Batten TW User Manual

10 WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This�marking�shown�on�the�product�or�its�literature,�indicates�that�it�should�not�be�disposed�� with�other�household�wastes�at�the�end�of�its�working�life.�To�prevent�possible�harm�to�the�� environment�or�human�health�from�uncontrolled�waste�disposal,�please�separate�this�from�other� types�of�wastes�and�recycle�it�responsibly�to�promote�the�sustainable�reuse�of�material�resources. Household�users�should�contact�either�the�retailer�where�they�purchased�this�product,�or�their� local�government�office,�for�details�of�where�and�how�they�can�take�this�item�for�environmentally� safe�recycling. Business�users�should�contact�their�supplier�and�check�the�terms�and�conditions�of�the�� purchase�contract.�This�product�should�not�be�mixed�with�other�commercial�wastes�for�disposal.

Other DJ Equipment Manuals