Precor Experience 800 Assembly Manual

Text of Precor Experience 800 Assembly Manual

Experience™ Series 800 Line

Treadmill (TRM) Assembly Guide English Français Deutsch 日本語 中文 Español Português brasileiro

Table of Languages

English 1 Français Deutsch 日本語 中文 Español Português brasileiro 11 22 33 44 55 66

Precor Experience 800 Follow the steps in the order listed in this assembly guide. For more product information,

visit us at www.precor.com. WARNING At least two people are required to assemble the equipment. DO NOT attempt assembly by yourself. Assembly requirements Important Before you fully tighten a fastener, check that its head is flush with the surface of the equipment. If not, cross-threading may have occurred. DO NOT attempt to rework the assembly

Required tools and hardware

Tools Hardware kit • Hex wrenches: 5/32, 3/16, and 7/32-inch • 3/4-inch open end wrench • 7/16-inch-pound torque wrench • #3 Phillips screwdriver • Roll of string or fish tape Component Quantity Component Quantity Buttonhead screw (3/8-inch x 1-inch 12 Buttonhead screw (3/8-inch x 1-inch) 6 Narrow flat washer (3/8-inch) 12 Buttonhead screw (1/4-inch x 1-inch) 4 2

After unpacking, follow the ramp assembly instructions (included) on how to

build and use a ramp to safely and securely roll the treadmill base off the shipping pallet. Important Make sure the treadmill is sitting on the ground. 2. Remove the hood off the treadmill base and set aside. 3. Place the upright support (right side) onto its base frame side bracket. Route the data cable from the treadmill drive unit through the smaller channel

Begin assembly, continued

1. Rewire the treadmill (see Figure 4) using the following console cables: — Ethernet — TV (coaxial) — Power Figure 4 2. Partially tighten the fairing to the upright supports on both sides using six screws and six washers for each side (see Figure 5). Make sure the fairing is not externally supported. Important DO NOT wrench tighten the fasteners in the above step until the unit has been fully assembled. Make sure the cable

Precor Experience 800 Touchscreen consoles only

To attach the filter to the drive power cable: 1. Disconnect the existing power cable from the drive unit, power filter, and ground terminal. Then completely remove it from the treadmill (see Figure 6). Figure 6 2. Connect the new power cable according to Figure 7 and Table 1. Figure 7 Table 1 Position Connector Drive input connectors Brown lead with quick-connect terminal Blue lead with quick-connect terminal Green and yellow lea

Install the accessory jack panel

1. Remove the screws securing the blank plate at the right-front corner of the treadmill (see Figure 8). Discard the blank plate. Figure 8 2. Thread the cable assembly down through the channel in the upright support on your right (see Figure 9). Drape excess cable over the inside edge of the support and tape into place, if necessary. Figure 9 3. Pass the lower end of the TV cable through the right-hand grommet, and insert i

Complete the assembly

1. Attach both corner covers and secure each with one screw (see Figure 10). Figure 10 2. Refer to the console Installation Guide (either online or in the console box) for instructions on how to install the console, including replacing the power harness. Once you’re done, come back to this page and complete the treadmill assembly from the next step onward. 3. To position the hood, gently flex the bottom edge of the hood around the b

Level the treadmill

It is important to level the TRM properly every time you move it. CAUTION To eliminate movement, make sure the adjustable feet are in contact with the floor. Also, make sure that the unit sits on a flat surface. Adjusting the feet of the unit cannot compensate for extremely uneven surfaces. Important Adjust only one rear foot at a time. DO NOT extend the adjustable feet more than 3/4 inch (2 cm). Adjusting the rear feet can’t compens

Adjust the running belt tracking

1. Start the treadmill and set the speed to 3 MPH (5 KPH). 2. Observe the running belt tracking while verifying that the belt remains centered: If the belt starts... Then… To drift toward the right slowly and manually turn the right side take-up roller mounting bolt clockwise (see Figure 13) in quarter- turn increments until the drifting stops. To drift toward the left slowly and manually turn the right side take-up rolle

Check the alignment of the running belt

1. Turn on the treadmill. 2. Standing beside the treadmill (not on it), press GO or QuickStart on the console. 3. Press SPEED UP until the console shows a speed of 3 MPH (5 KPH). 4. Observe the belt from the rear of the treadmill for a few minutes. The belt should remain centered along the running bed. If it drifts off center, adjust it (refer to Adjust the running belt tracking section). Important Failure to align

Precor Experience 800 Exigences relatives à l’assemblage

Suivez les étapes dans l’ordre indiqué dans ce guide d’assemblage. Pour obtenir plus d’informations concernant le produit, rendez-nous visite sur www.precor.com. AVERTISSEMENT Un minimum de deux personnes est nécessaire pour assembler l’équipement. Ne tentez PAS l’assemblage par vous-même. Exigences relatives à l’assemblage Important Avant de serrer complètement une vis, vérifiez que sa tête est a

Outils et visserie requis

Outils et kit de visserie • Clés hexagonales : 5/32, 3/16 et 7/32 po • Clé plate 3/4 po • Clé dynamométrique 7/16 po-lb • Tournevis Phillips n° 3 • Aiguille d’électricien Composant Quantité Composant Quantité Vis à tête bombée (3/8 po x 1 po) 12 Vis à tête bombée (3/8 po x 1 po) 6 Rondelle étroite plate (3/8 po) 12 Vis à tête bombée (1/4 po x 1 po) 4 12

Après le déballage, respectez les instructions d’assemblage de la rampe

(incluses), qui indiquent comment construire et utiliser une rampe pour dérouler la base du tapis de course hors de la palette de transport en toute sécurité. Important Veillez à poser le tapis de course sur le sol. 2. Retirez le capot de la base du tapis de course et mettez-le de côté. 3. Placez le montant vertical (côté droit) sur son support

Precor Experience 800 Commencer l’assemblage (suite)

Pour recâbler le tapis de course : 1. Recâblez le tapis de course (voir Figure 4), en utilisant les câbles de console suivants :  Ethernet  TV (coaxial)  Alimentation Figure 4 2. Serrez partiellement le carénage sur les montants verticaux des deux côtés, à l’aide de six vis et de six rondelles de chaque côté (voir Figure 5). Assurez-vous que le carénage n’est pas soutenu extérieurement. Important NE

Consoles à écran tactile uniquement

Pour fixer le filtre au câble d’alimentation de l’entraînement : 1. Débranchez le câble d’alimentation existant de l’unité d’entraînement, du filtre de puissance et de la borne de mise à la terre. Retirez-le ensuite complètement du tapis de course (voir Figure 6). Figure 6 2. Branchez le nouveau câble d’alimentation conformément à la Figure 7 et au Tableau 1. Figure 7 Tableau 1 Poste Connecteur C

Installer le panneau de branchement des accessoires

1. Retirez les vis fixant la plaque vide au coin avant droit du tapis de course (voir Figure 8). Mettez au rebut la plaque vide. Figure 8 2. Acheminez l’ensemble des câbles vers le bas, dans le chemin de câble du montant vertical situé à votre droite (voir Figure 9). Faites passer le surplus de câble au-dessus du bord intérieur du support et, si nécessaire, maintenez-le en place avec du ruban adh

Precor Treadmill Owners Instructions: