Vicon ROUGHNECK V910 Installation & Operation Manual

Rev 809 Section 3 XX137-86-03 V910 IMPACT-RESISTANT DOME CAMERAS WITH DIGITAL NOISE REDUCTION Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose. Copyright © 2009 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are r ...

A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide reasonable protection against such interference in a commercial installation. However, there i ...

The lightening bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock. The exclamation point symbol alerts the user to the presence of important operating and maintenance instructions. 1. Read Instructions - Read all safety and operating instructions before the product is operated. 2. Retain Instructions - Retain all safety and operating instructions for future reference. 3. Heed Warnings - Pay attention to all product warnings. 4. Follow Instructions - Follow all operating instructions. 5. Cleaning -(Do not use caustic, abrasive or aerosol cleaners) a ...

Contents • i Contents Quick Installation ................................................................................................................ii Introduction .........................................................................................................................1 Installation ...........................................................................................................................3 Unpacking and Inspection.............................................................................................................................3 Roughneck V910 Dome ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR Quick Installation For complete detailed instructions on how to install the V910, read the Installation section. Installation Diagram ...

Introduction • 1 Introduction The information in this manual covers the installation, operation, and maintenance of the Roughneck™ V910 Series of Impact-Resistant Dome Cameras with Digital Noise Reduction (NR). These units should only be installed by a qualified technician using common hand tools and approved materials and wiring methods in accordance with the national Electrical Code ANSI/NFPA 70, state and local wiring codes. When installing this equipment, use only a UL Listed Class 2 indoor/dry or Class 3 outdoor/wet rated power supply. Read this manual through completely before attempti ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR Table 1 Models, Product Codes and Descriptions Model Product Code Description Power (W) PoE Power (W) Nom./Max* Current Rating (A) Nom./Max. V910A-NR/ V910A- NRC 9246-04/ 9246-03 Indoor/Outdoor; 1/3-in. high-resolution color camera with 3.3 - 12 mm varifocal autoiris lens; 24 VAC capability; isolated power input; coaxial video transmission; no heater. NTSC/PAL. -- 3.0 0.1 V910A-NRIP5/ V910A-NRIP5C 9246-75/ 9246-76 Indoor/Outdoor; 1/3-in. high-resolution color camera with 3.3 - 12 mm varifocal autoiris lens; PoE or 24 VAC capability; isolated power input; heater; ViconNet (ver. ...

Installation • 3 Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition as it left the factory. Inspection for Visible Damage Immediately inspect the cartons upon delivery. Make a note of any visible damage on all copies of the carrier’s freight bill. Make sure the carrier’s agent (the person making the delivery) signs the note on all copies of the bill. If the agent does not have claim forms, contact the carrier’s office. Inspection for Concealed Dam ...

Installation • 5 Figure 1 Exploded View ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR Accessory Kit There is an accessory kit included with the Roughneck V910. The table below lists the contents. Description Quantity Tamperproof driver bit, ¼ hex T-15 (to remove tamperproof screws) 1 Pipe sealant tape (to seal pipe fitting to housing) 1 Screws (for some appropriate installations) 4 Terminal block, 2-pin (24 VAC heater power) (IP versions only) 1 Terminal block, 3-pin, for alarm (IP versions only) 1 Tool for set screw roll adjustment 1 Lens focusing tool 1 ViconNet CD (IP versions only) 1 Mounting the Unit Select a location for the installation of the V910 came ...

Installation • 7 3. There are two (2) cable access holes provided. Drill a hole in the wall or ceiling and route video and power cables to the selected location and through one of the cable access holes. A 1/2-inch connection (customer-supplied connector) is provided on the side of the base; the rear port is sized to accept a 1/2- in. (customer-provided) connector. A conduit or electrical connector (screw-type) can be used in this threaded hole. See Figures 1 and 2 for hole locations. Apply the provided sealant tape around the threads of the conduit pipe. 4. If it is desirable to use the rear ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR on the camera/lens assembly; this marks the TOP of the camera. Make sure the camera/lens is installed so that the label is on the top for proper video display. Figure 4 Camera Position Adjustments ...

Installation • 9 Cable Connections For non-IP models, power and video are made to the BNC and power supply board in the base of the unit. Power, video, alarm, audio and IP connections are made to the printed circuit board (PC board) on IP units. Refer to Figure 5 when performing these connections. Refer to the Cable Recommendations in the Reference section. The V910 IP models provide support for direct network connection to Kollector Elite Digital Video Recorders and ViconNet Workstations via ViconNet software. The PC board allows direct plug-in to a system network hub, switch or router. Video ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR CONNECTOR/PIN NUMBER CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME TERMINAL BLOCK POWER (TB3) TB3-1 24 24 VAC TB3-2 24 24 VAC TERMINAL BLOCK ALARM (P1) P1-1 ALARM OUT Alarm output P1-2 GND Ground P1-3 ALARM IN Alarm input RJ-45 LAN (J7) J7-1 TX + Transmit + J7-2 TX - Transmit - J7-3 RX + Receive + J7-4 J7-5 J7-6 RX - Receive - J7-7 J7-8 1/8-IN. PHONO AUDIO J3 MIC Audio In J6 SPK Audio Out - N/A Wiring Connections for IP Models Dome Power Connections Note: Vicon systems and components, like most electronic equipment, require a clean, stable power source. Voltage irregularitie ...

Installation • 11 Table 2 Dome Power Connections Pin Number Function 1 24 VAC 2 24 VAC Return Note: A grounding tab (P6) is provided on the PC board of the IP cameras for those installations requiring a ground. The use of the ground tab to earth ground is necessary to provide protection to the camera. Heater Connections The V910 IP versions have a heater in the base for those installations requiring it. Refer to Figure 1. The unit is delivered with the heater connection made to the connector (P8) on the PC board. The heater requires 24 VAC. Refer to Figure 5. Camera/Lens Adjustments After all ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR Special Menu Function Summary CAMERA ID OFF, English uppercase or lowercase letters, numerals 0~9, -, null Maximum length for the name display is 15 letters. OFF is the default setting. DAY/NIGHT AUTOㆍBWㆍEXTERNㆍCOLOR AUTO mode (default): Day/Night electronically changes to the appropriate mode: -Daytime: COLOR mode -Night-time: BW mode COLOR mode: Always COLOR mode BW mode: Always BW mode EXTERN mode: CDS external signal input SYNC INTㆍLL LL mode: Adjust desired phase from 0°~359°, Auto-detection. INT is the default setting. MOTION DETECTION OFFㆍON ON mode: AREA ( ...

Installation • 13 LENS Select according to lens type: Manual Iris Lens: Manual mode DC Drive Lens: DC mode Manual Iris Lens In Lens menu, select MANUAL if using a manual iris lens. DC Drive Lens In Lens Menu, select DC. In the screen that follows, adjust the brightness level using menu buttons on the bar, 1-70. DC 25 is the default setting. SHUTTER Shutter provides a choice of MANUAL, ESC and FLK. MANUAL mode allows shutter speed to be manually selected between 1/60(50) – 1/120,000 seconds. The ESC (Electronic Shutter Control) mode allows adjusting the brightness on the bar, 1-70. In FLK (Fl ...

XX137-86-03 Rev 809 Roughneck V910 Dome Cameras with NR WHITE BALANCE This function is used to set the best color in the current environment. Use the ATW mode when color temperature is between 1,800 and 10, 500° K. AWC mode finds the optimal setting for the current luminance environment. If camera has a full white screen in front of white paper, the camera is fixed at the best color temperature. Push the joystick button to set. When the environment is changed, new settings are needed using the same method. White Balance can be directly adjusted by user in Manual mode. The value of Red and Blue can be controlled (0-256). Consideri ...