Antec ISK 300-65 Operation & User’s Manual

Text of Antec ISK 300-65 Operation & User’s Manual

TABLE OF CONTENTS

INTRODUCTION 1.1 Case Specifications.…..………………………………………………………………………………….. 3 1.2 Diagram…………………………………………………………………….…………………………………. 3 1.3 Power Supply Specifications…………………………………………………………………………. 4 HARDWARE INSTALLATION GUIDE 2.1 Removing the Top

ISK 300-65 USER’S MANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures. For

96mm (H) X 222mm (W) X 328mm (D)

3.8” (H) x 8.7” (W) x 12.9” (D) Net Weight 5.5 lbs / 2.5 kg Cooling 1 x Side 80mm TriCool™ fan Drive Bays 3 Drive Bays: - 1 x External 5.25” slim drive bay - 2 x Internal 2.5” drive bays Expansion Slots 1 x Half-height slot Motherboard Size Mini-ITX Front I/O Panel 2 x USB 2.0 1 x eSATA AC’97 / HD Audio In and Out Power Adapter EP-65 p

POWER SUPPLY SPECIFICATIONS

The ISK 300-65 is powered by an EP-65 power adapter. Input characteristics: Input Voltage Range Frequency Range 100 VAC ~ 240 VAC 50 Hz ~ 60 Hz Output characteristics: Continuous Power Rated Voltage Voltage Range Output Current Ripple & Noise 65W 19V 18.4V ~ 20.0V 0A ~ 3.42A < 350mV A variety of industrial-grade safety circuitry will help protect your computer: OVP (Over Voltage Protection), SCP (Short Circuit Protection),

HARDWARE INSTALLATION GUIDE

2.1 REMOVING THE TOP PANEL Place the case flat on an even, stable surface. 1. Remove the three thumbscrews from the rear of the top panel. 2. Grip the top panel and slide it back several inches until it stops. 3. Grip the panel from the sides and lift it up until it pulls completely free of the main chassis. Note: Do not use your fingernails to pry or lift the panels. 2.2 REMOVING THE DRIVE TRAY ASSEMBLY Remove the top pane

2.4 INTERNAL 2.5” DEVICE INSTALLATION

Remove the top panel as described in section 2.1. Included at the top of the drive tray assembly is a HDD tray that can support up to two 2.5” devices. 1. On the right side of the drive tray assembly, remove the thumbscrew holding the HDD tray to the rest of the device. 2. Slide the HDD tray back a centimeter so the locking hinges unhook. 3. Pull the HDD tray away from the drive tray assembly. 4. Align your 2.

USB Power 1

2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connection) 10 Empty Pin Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L)

3.4 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS

Connected to your front panel are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard user’s manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try re

Antec Enclosure Owners Instructions: