Intralock Tools 950C Operation Manual

1 - Press Display will read MANUFACTURER 300 INSERT 2 FLAT 1 2 - Press Display will read BI-AXIAL ENTERY M0DE SELECTED 3 - Press Display will read BI-CODE = 4 ...

Intralock Tools 950C NOTE For nickel silver blanks our ITL MD1027 CARBIDE CUTTER should be used. Cutting keys generated by Master Key Program 1. Generate Master Key system. Follow instructions on page 17. 2. Push This will enable use of the Generated system. 3. Select key number from printed chart Press (key number), or continue to press . to ...

Incorrect maximum space number. Range is 1 through 10. INVALID MAXDPT # Incorrect maximum depth number. Range is I through 10 INVALID MINDPT # Incorrect minimum depth number. Range is 0 or 9. INVALID BAUD RATE Incorrect baud rate number. Range is 1 through 8. ERROR LOADING TABLE Remote code load has failed. Check serial port paramete ...

Intralock Tools 950C 1 * Specifications 2 * Key Functions 3 OPERATION * Starting the ITL950C 4 * Selecting a Manufacturer 4 * Entering a Code 4 * Cutting a Key 4 * Calibrating the ITL950C. 5 * Setting Correction Factor 6-7 III CUSTOM CONFIGURATION * Setting the default manufacturer ID 8 * Setting units (metric – inches). 8 * Setting defa ...

Intralock Tools 950C INSERT NUMBER OFFSET FROM TRUE 0 RANGE OF DEPTHS 1 0.000 INCHES 0.465 - 0.180 INCHES 2 0.035 INCHES 0.430 - 0.145 INCHES 3 0.070 INCHES 0.395 - 0.110 INCHES 4 0.100 INCHES 0.365 - 0.080 INCHES EXTENDED TABLE Press the ITL950C now displays EXTENDED TABLE Y/N Press to toggle. The t ...

Intralock Tools 950C In the laser cut mode cuts are made from flat edge to flat edge without the normal inbetween cut points. From the ready prompt push the C.F. key three times, the display will read normal cut mode. Push the (-) key to toggle to the laser cut mode and back to the normal cut mode. HALF DEPTH MODE 4. Press four times. The ...

Intralock Tools 950C The default or power on ID is the MFG ID number the machine selects when reset or turned on. As with any ID, it must be in the range of 1 through 960, and the table must be correct. It can be set by you and remains set until you select a different ID. 1) Press the keys to enter the EDIT mode. The display will show EDIT. 2) ...

Intralock Tools 950C The, ITL950C should be plugged in to a switch operated power bar with surge suppression. Check serial plate for correct machine voltages and current requirements. Turn on the power switch lo- cated on the back of machine. Follow instructions on the display. (Move vise to right or left.) 12-VOLT POWER INVERTERS THE USE OF A POWER INVE ...

Intralock Tools 950C SETTING BAUD RATE Enter the EDIT mode by pressing the keys. Press twice to enter the Serial port setup routine. Display will read BAUD RATE =8. Use the table below to select a baud rate. For example to set the baud rate to 4800, locate the correct baud rate (in this c ...

NOTE: PARAMETER TABLE IS COMPLETE PLEASE REVIEW THE TABLE FOR ACCURACY. To review the table, continue pressing the key until the display returns to EDIT. SETTING VALUES IN SPACE TABLE Press the ITL950C will display; SPACE 1 = (0000). Enter the desired space information in thousandths of and inch e.g. .250. Press on th ...

Intralock Tools 950C Set Masterkey Set Grandmasterkey MK = _____ Step control 22222 # of Changekeys MACS Limit 6 Max duplicate cuts 3 Change advanced Variables Generate Masterkey System Generating Masterkey System Print Reports to Remote Send Masterkey Report to computer for Printing Send Hardware Report to computer for Printing Send Keying Char ...