Vicko THMGC500A Instruction Manual

Model No: THMGC500A Ref. No: 876-4409 INSTRUCTIONS MANUAL ...

1. This appliance is designed for private, domestic use only. No responsibility is accepted for damage resulting from use non-compatible with the instructions. 2. The appliance is not intended to be used in the following applications, and the guarantee will not apply for:  Any commercial use.  Staff areas in shops, offices and other working environments.  Farm houses.  By clients in hotels, motels and other residential, bed and breakfast type environments. 3. This appliance is used only as tomato juicer for preparing tomato juice and meat grinder for preparing minced meat, sausages and kubbe. 4. The ...

22. Always use the device in an upright position. 23. Do not operate the appliance with wet hands. 24. Do not use while you are in contact with water. 25. Do not immerse the appliance in water or any other liquids. 26. Do not touch an appliance that has fallen into water. Just pull the plug off. 27. Do not use the device when it is empty. 28. Never process with the appliance food / ingredients that are frozen. Defrost frozen ingredients thoroughly before you process them with the appliance. 29. Never process with the appliance food / ingredients that are too hot. Let hot ingre ...

moisture and high or very low temperature. Avoid direct exposure under ultraviolet. 48. Always make sure the appliance is clean and dry before storing it. 49. Do not store the appliance while it is still warm. CAUTION! Read all the instructions carefully before you use the appliance and keep them for future use. When passing on the appliance to a third person, make sure to include these instructions for use. WARNING! The appliances are not intended to be operated by means of an external timer or separate remote-control system. WARNING! This appliance is not intended for use by ...

are recyclable. 2. Keep plastic bags away from babies and children. 3. After you remove the device from its packing, clean it with a damp cloth. 4. Clean the appliance according to the instruction in the “CLEANING” paragraph. Never put the appliance under running water in order to clean it. 5. Place the appliance on a flat, stable and dry surface. Never place the appliance on a soft surface. 6. Before using the device unfold the cord completely and make sure that it does not show any signs of damage. 7. Ensure that the main voltage rating of your power ...

2. “ON / R” Switch (ON / Reverse) 3. “ON / 0 / R” Switch (ON / OFF/ Reverse) 4. Release button (for Milling tube) 5. Inlet for the Milling tube 6. Milling tube 7. Feed screw (metal) 8. Feed screw (plastic) 9. Juicing strainer (metal) 10. Bracket (for the plastic feet screw and metal juicing strainer) 11. Regulator for peels & juice separation 12. Exit spout for peels and spores 13. Nut 14. Juice collector tray 15. Bracket cover 16. Feed hopper 17. Food pusher 18. Cutter Blade 19. Cutting Plate (3 pcs for fine / medium / coarse cut) 20. Sausage stuffer adaptor 21. Kubbe attachment ...

Position “ON”: Normal Function Position “R”: Reverse Function “ON / 0 / R” Switch Position “ON”: Normal Function Position “0”: Deactivate (OFF) Position “R”: Reverse Function Normal Function (Juicing / Grinding) Both switches (“ON / R” Switch and “ON / 0 / R” Switch) should be in position “ON” for Normal Function. Reverse Function: This function is used ONLY for removing obstructions that appear during processing of food. Never use the reverse function continuously or for long time. Both switches (“ON / R” Switch and “ON / 0 / R” Switch) should be in position “R” for ...

ATTENTION: Always make sure the appliance is unplugged from the power supply before starting to assemble or disassemble it. Never assemble or disassemble any accessory when the appliance is in operation. Assembling the milling tube: Put the milling tube (6) in the inlet (5) and turn it counterclockwise to “lock” in position. Warning: Install the milling tube properly, a misplaced milling tube will result in a not sufficient type of milling quality and may cause weakening or damage to other accessories. Disassembling the milling tube: Press the release button (4) ...

Please follow the instructions below. 1. Put the milling tube (6) in the inlet (5) on the main unit. 2. Place and fit the metal feed screw (7) inside the milling tube (6). 3. Place and fit the plastic feed screw (8) as an extension of the metal feed screw (7). 4. Place the metal juicing strainer (9) inside the bracket (10). 5. Put the bracket (10) on the milling tube (6) and make sure the plastic feed screw (8) is located inside the strainer. ...

(13) to lock in position all accessories at the edge of the milling tube (6). Warning: Do not over tighten! 7. Place and fit the Juice collector tray (14) on the bracket (10). 8. Put the bracket cover (15) on the bracket (10). 9. Put the feed hopper (16) on the top of the milling tube (6) 10. The appliance is ready for use. Note: For disassembling please use the above instructions in reverse order after you make sure the appliance is not connected to the power supply and is cooled down. ...

Please follow the instructions below. 1. Put the milling tube (6) in the inlet (5) on the main unit. 2. Place and fit the metal feed screw (7) inside the milling tube (6). ...

blade (18) on the metal feed screw (7). 4. Put ONE cutting plate (19) on the metal feed screw (7) after the cutter blade (18). 5. Put and screw the nut (13) to lock in position all accessories at the edge of the milling tube (6). Warning: Do not over tighten! Note: The appliance is equipped with 3pcs of cutting plates which are proper for fine / medium / coarse cut. Use the cutting plate according to the desired result you need. Warning: Face the cutter blade cutting side to the cutting plate. If the cutter blade is installed improperly, it will not grind the food. Warning: Do not ever place 2 or 3 cutting plates together ...

Please follow the instructions below. 1. Put the milling tube (6) in the inlet (5) on the main unit. 2. Place and fit the metal feed screw (7) inside the milling tube (6). ...

cutter blade (18) on the metal feed screw (7). 4. Put ONE cutting plate (19) on the metal feed screw (7) after the cutter blade (18). 5. Put the sausage stuffer adaptor (20) on the metal feed screw (7) after the cutting plate (19). 6. Put and screw the nut (13) to lock in position all accessories at the edge of the milling tube (6). Warning: Do not over tighten! Note: The appliance is equipped with 3pcs of cutting plates which are proper for fine / medium / coarse cut. Use the cutting plate according to the desired result you need. Warning: Face the cutter blade cutting side to the cutting plate. If the cutter blade is installed ...

Please follow the instructions below. 1. Put the milling tube (6) in the inlet (5) on the main unit. 2. Place and fit the metal feed screw (7) inside the milling tube (6). ...

metal feed screw (7). 4. Put and screw the nut (13) to lock in position all accessories at the edge of the milling tube (6). Warning: Do not over tighten! 5. Put the feed hopper (16) on the top of the milling tube (6) 6. The appliance is ready for use. Note: For disassembling please use the above instructions in reverse order after you make sure the appliance is not connected to the power supply and is cooled down. ...

Using the appliance as Tomato Juicer: Always make sure to prepare the tomatoes you are about to process before you use the appliance.  Slice the tomatoes in small pieces so that they fit easily into the feed hopper opening.  Make sure that all stalks are removed.  Place all prepared tomatoes in a bowl near the appliance in order to be able to feed the hopper easy. After you prepare the tomatoes you are about to process, follow the instructions below in order to use the appliance: 1. Make sure the appliance is not connected to the power supply. 2. Put the appliance on a flat and stable surface. 3. Assemble ...

fingers. Use only the food pusher (17) supplied to you with this appliance.  To avoid obstructions do not apply excessive force while pushing food.  If any hard piece of food stops the screw and blade rotation, immediately switch OFF the appliance, wait till the screw stops rotating and use the reverse function by pressing both switches to position “R” in order to remove the obstruction before starting again. If the obstruction is not removed please switch off the appliance, disconnect from power supply, disassemble the accessories and remove the ...

Always make sure to prepare the food you are about to process before you use the appliance.  Defrost frozen meat thoroughly.  Slice the meat in small cubes or stripes so that they fit easily into the feed hopper opening.  Make sure that all bones, tendons, cartilages, veins and excess fat are removed.  Place all prepared meat in a bowl near the appliance in order to be able to feed the hopper easy. After you prepare the meat you are about to process, follow the instructions below in order to use the appliance: 1. Make sure the appliance is not connected to the power supply. 2. Put the appliance on a f ...

horseradish) with the appliance.  Never push food into the milling tube (6) with any foreign objects or with your fingers. Use only the food pusher (17) supplied to you with this appliance.  To avoid obstructions do not apply excessive force while pushing food.  If any hard piece of food stops the screw and blade rotation, immediately switch OFF the appliance, wait till the screw stops rotating and use the reverse function by pressing both switches to position “R” in order to remove the obstruction before starting again. If the obstruction is not removed ple ...